3 Drawer Base Cabinet Assembly
|
|
- Tomás Ortega Ramírez
- hace 6 años
- Vistas:
Transcripción
1 3 Drawer Base Cabinet Assembly WARNING Excessive Weight Hazard Use two or more people to move and assemble cabinet. Failure to do so can result in back or other injury. PARTS: TOP BACK (2) SIDE (2) BOTTOM DRAWER BACK (3) DRAWER BOTTOM (3) DRAWER BOTTOM SUPPORT (3) DRAWER FRONT (3) DRAWER SIDE (6) SLIDE BRACKET (6) OUTER SLIDE INNER SLIDE HANDLE (3) LEVELER (4) BOLT (26) NUT (26) SCREW (90) HANDLE SCREW (6) NAMEPLATE
2 1. Assemble the top and bottom to the side panels with 4 screws each. Do not over tighten the screws. Screw the 4 levelers completely into the bottom panel. Holding the top, carefully lift the cabinet to the upright position. Continue to step 2 to assemble the back panels. TOP 2. Starting at the bottom, screw the 2 back panels to the cabinet back using 6 screws on each panel. Do not over tighten the screws. 1 SIDE 3. Disassemble the inner and outer slides by pushing down on the locking latch of the slide tab while pulling apart allowing the two parts to come apart. 3 SIDE BOTTOM OUTER SLIDE 4 BACK (2) 2 4. Clip the outer slides to the slide brackets and fasten with a nut and bolt. NOTE: The nut must be on the bracket side (inside) as shown. SLIDE BRACKET 5. Attach the 6 slide assemblies to the inside of the cabinet. Insert the bracket tabs into the slots in the back of the cabinet and fasten the front with 2 screws. Do not over tighten the screws. 5 Place the cabinet in its desired location. Level the cabinet adjusting the levelers through the bottom panel access holes
3 Keep these holes towards front of drawer SIDE DRAWER ASSEMBLY Assemble the 3 drawers as described in steps Attach the drawer bottom to the drawer sides using 3 screws on each side. NOTE: Keep the square holes in the side panels towards the front as shown. BOTTOM SUPPORT Attach the support bracket to the bottom as shown using 2 screws. SIDE 7. Attach the drawer back with 10 screws as shown. BOTTOM 6 NOTE: Keep the square holes in the side panels towards the front as shown. Keep these holes towards front 8 Keep these holes at the top BACK FRONT BOTTOM SUPPORT Hook the bottom support into the bottom edge of the drawer front and attach the drawer front with with 4 nuts and bolts as shown. NOTE: Keep the handle holes at the top as shown. 9. Clip the slides to the drawer sides into the square holes on the outside of the drawers and fasten with a nut and bolt. NOTE: The nut must be on the inside of the drawer as shown. Attach the handle with 2 bolts as shown
4 Install the drawers by aligning the inner and outer slides. Push the drawer closed until it locks in place. Install the drawer with the nameplate holes on the top and snap in the nameplate until flush on the drawer face To remove the drawer pull the drawer all the way open. Push down on left slide tab and push up on the right slide tab. This will release the drawer allowing the drawer to be pulled out of the cabinet body. WARNING! Place heaviest loads in bottom drawers to prevent cabinet tipping. Maximum Weight Limits Top drawer: 25 lbs. (11 KG) Middle drawer: 50 lbs. (22 KG) Bottom drawer: 50 lbs. (22 KG) Cabinet: 125 lbs. (55 KG) total
5 Armoire sur plancher à trois tiroirs Assemblage AVERTISSEMENT Poids excessif Toujours se mettre à deux pour déplacer et monter l'armoire. Ne pas observer cette recommandation peut causer des blessures et notamment au dos. PIÈCES: DESSUS ARRIÈRE (2) LATÉRAL (2) FOND ARRIÈRE DE TIROIR (3) FOND DE TIROIR (3) SUPPORT DE FOND DE TIROIR (3) AVANT DE TIROIR (3) LATÉRAL DE TIROIR (6) SUPPORT DE COULISSE DE TIROIR (6) COULISSE EXTÉRIEURE COULISSE INTÉRIEURE POIGNÉE (3) PATIN RÉGLABLE (4) BOULON(26) ÉCROU (26) VIS (90) VIS DE POIGNÉE (6) PLAQUE DU FABRICANT
6 1. Assemblez le dessus et le fond aux panneaux latéraux en utilisant quatre vis par panneau. Évitez de trop serrer les vis. Vissez complètement les quatre patins réglables sous le panneau du fond. En tenant le dessus, soulevez l armoire avec précaution en position verticale. Poursuivez à l étape 2 pour fixer les panneaux arrière. DESSUS LATÉRAL 2. En commençant au bas de l armoire, vissez les deux panneaux arrière à l armoire en utilisant six vis par panneau. Évitez de trop serrer les vis. 3. Désassemblez les rails interne et externe en pressant vers le bas sur le taquet de verrouillage de l onglet de la coulisse tout en tirant pour séparer les deux pièces. 3 1 LATÉRAL FOND COULISSE EXTÉRIEURE 4 4. Assemblez les coulisses extérieures aux supports de coulisse et fixez à l aide d un boulon et d un écrou. SUPPORT DE COULISSE ARRIÈRE (2) 2 NOTA : L écrou doit être du côté du support (à l intérieur), tel qu illustré. 5. Fixez les six mécanismes coulissants à l intérieur de l armoire. Insérez les languettes des supports dans les fentes à l arrière de l armoire et fixez à l avant à l aide de deux vis. Évitez de trop serrer les vis. 5 Placez l armoire à l emplacement voulu. Placez l armoire de niveau en ajustant les patins réglables par les trous d accès dans le panneau du fond
7 Placez ces trous à l avant du tiroir CÔTÉ ASSEMBLAGE DES TIROIRS Assemblez les tiroirs comme il est décrit dans les étapes 5 à Fixez le fond du tiroir aux côtés du tiroir en utilisant trois vis de chaque côté. NOTA : Placez les trous carrés dans les côtés vers l avant du tiroir, tel qu illustré. SUPPORT DU FOND Fixez le support de soutien sous le fond du tiroir, tel qu illustré, à l aide de deux vis. CÔTÉ 7. Fixez le derrière du tiroir à l aide de 10 vis, tel qu illustré. FOND 6 NOTA : Placez les trous carrés dans les côtés vers l avant du tiroir, tel qu illustré. Placez ces trous à l avant du tiroir 8 Placez ces trous en haut DEVANT DERRIÈRE SUPPORT DU FOND 7 8. Accrochez le support du fond au bord inférieur du devant du tiroir et fixez le devant du tiroir à l aide de quatre boulons et écrous, tel qu illustré. 9 NOTA : Placez les trous des poignées en haut, tel qu illustré. 9. Placez les coulisses des tiroirs contre les trous carrés à l extérieur des tiroirs et fixez à l aide des boulons et des écrous. NOTA : L écrou doit être à l intérieur du tiroir, tel qu illustré. Fixez la poignée à l aide de deux boulons, tel qu illustré
8 Installez les tiroirs en alignant les pièces intérieures et extérieures des coulisses. Refermez le tiroir jusqu à ce qu il s aligne en place. Installez le tiroir muni de trous pour la plaque du fabriquant en haut et fixez la plaque bien en place sur le devant du tiroir Pour retirer le tiroir, ouvrez le complètement. Appuyez vers le bas sur l onglet de la coulisse gauche et tirez vers le haut sur l onglet de la coulisse droite pour dégager le tiroir et vous permettre de le sortir complètement. AVERTISSEMENT! Placez les articles les plus lourds dans les tiroirs du bas pour éviter que l armoire bascule. Limites de poids maximal Tiroir du haut : 11 kg (25 lb) Tiroir du centre : 22 kg (50 lb) Tiroir du bas : 22 kg (50 lb) Armoire : 55 kg (125 lb) au total
9 Gabinete De 3 Cajones Assemblea ADVERTENCIA Peligro de Peso Excesivo Utilice a dos personas o mas para mover o instalar el gabinete. Si no lo hace, puede causar daños a la espalda u otro tipo de daño PARTES: ARRIBA PANEL TRASERO (2) LADOS (2) ABAJO TRASERO DEL CAJON (3) ABAJO DE EL CAJON (3) SOSTEN PARA ABAJO DEL CAJON (3) ARRIBA PARA EL CAJON (3) LADOS PARA LOS CAJONES (6) SOPORTE DE RESBALE (6) DIAPOSITIVA e RESBALE EXTERNA DIAPOSITIVE e RESBALE INTERNA MANIJERAS (3) NIVELADOR (4) PERNOS (26) TUERCAS (26) TORNILLOS (90) TORNILLOS PARA LAS MANIJERAS (6) PLACA DE IDENTIFICACIÓN
10 1. Ensamble la tapa de la parte inferior de los paneles laterales con 4 tornillos cada uno. No Sobre apriete los tornillos Coloque los tornillos the los 4 niveles completamente en el panel de la parte inferior. Sosteniendo la tapa, levante cuidadosamente el gabinete a la posición vertical. Continúe el paso 2 montando la parte posterior de los paneles. 2. Comenzando en la parte inferior, atornille los 2 paneles traseros al gabinete detrás usando 6 tornillos cada uno. No Sobre apriete los tornillos. 1 ARRIBA LADOS 3. Desmonte los diapositivas internas y externas empujando hacia abajo en el cierre de fijación de la lengüeta ediapositiva mientras estirando / separando permitiendo que las dos piezas se separen. 3 LADOS ABAJO DIAPOSITIVA e RESBALE EXTERNA PANEL TRASERO (2) 2 4. Asegure los deslizadores externos con los soportes y aprietelos con una tuerca y un tornillo. NOTA: La tuerca debe estar en el lado del soporte (adentro) como se muestra. SOPORTE DE RESBALE 4 5. Coloque los 6 sportes para deslizar ya ensamblados al interior del gabinete. Inserte las lengüetas del soporte en las ranuras en la parte posterior del gabinete y sujete el frente con 2 tornillos. NoSobre apriete los tornillos. 5 Coloque el gabinete en su localización deseada. Nivele el gabinete que ajusta a los niveladores a través de los agujeros de acceso del panel inferior
11 Mantenga estos agujeros hacia el frente del cajón LADOS PARA LOS CAJONES Montaje del Cajon Ensamble de 3 cajones según lo describe en pasos Coloque la parte inferior del cajón a los lados del cajón usando 3 tornillos en cada lado. NOTA: Guarde las perforaciones rectangulares en los paneles laterales hacia adelante como se muestra LADOS PARA LOS CAJONES 8 SOSTEN PARA ABAJO DEL CAJON ABAJO DE EL CAJON 7 ARRIBA PARA EL CAJON Mantenga estos agujeros en la parte de arriba de la Coloque el soporte a la parte inferior como se muestra usando 2 tornillos. 7. Coloque la parte posterior del cajón con 10 tornillos como se muestra. NOTA: Guarde las perforaciones rectangulares en los paneles laterales hacia adelante como se muestra. TRASERO DEL CAJON Mantenga estos agujeros hacia el frente del cajón SOSTEN PARA ABAJO DEL CAJON 7 8. Asegure el soporte de la superficie de abajo delcajon con el frente del cajón y ate el frente del cajón con 4 tuercas y tornillos grandes como se muestra. 9 NOTA: Guarde los agujeros de la manija en la tapa como se muestra 9. 8 Sujerte los deslizadores a los lados del cajón en las perforaciones rectangulares por fuera de los cajones y sujete con una tuerca y un tornillo. NOTA: La tuerca debe estar en el interior del cajón como se muestra. Ate la manija con 2 tornillos como se muestra
12 Instale los cajones alineando los brackets internos y externos. Empuje el cajón hasta que cierre y este en sul lugar. Instale en el cajón la placa de identificación con los agujeros y encájese a presión en la placa de identificación hasta ruborar la cara del cajón 11. Para quitar el cajón, empuje el cajón hasta el final que quede todo abierto. Empuje hacia abajo en direccion izquierda del bracket y empuje hacia arriba en direccion del bracket. Esto ayudara y permitira que el cajón sea sacado del cuerpo del gabinete. 11 ADVERTENCIA! Ponga las cargas más pesadas en los cajones inferiores para prevenir el inclinamiento del gabinete. Limites Maximos de Peso Cajon de Arriba: 25 Libras (11 Kilogramos) Cajon de Enmedio: 50 Libras (22 Kilogramos) Cajon de Abajo: 50 Libras (22 Kilogramos) Gabinete: 125 Libras (55 Kilogramos) Total
MULTI-FUNCTIONAL COMPUTER TABLE
English MULTI-FUNCTIONAL COMPUTER TABLE ASSEMBLY INSTRUCTION IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents over surfaces
Más detallesMeijer.com A
English MOBILE LAPTOP CART STORAGE ASSEMBLY INSTRUCTION MODEL RTA - B00 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesJEEP WRANGLER 4 Door Top Kit
JEEP WRNGLER 4 oor Top Kit 82213651 82213652 10-16-12 65353 / 65370 Rev. 1 1 of 7 K6861654 JEEP WRNGLER 4 oor Top Kit B C E F G I J K L M 10-16-12 65353 / 65370 Rev. 1 2 of 7 K6861654 N 4X O P 8X T-30
Más detallesJEEP GRAND CHEROKEE 2011 RUNNING BOARDS ESTRIBOS LATERALES TUBULARES MARCHEPIEDS TUBULAIRES. LH 8mm 8mm 1.5" 6mm 8mm. 05-15-13 1 of 7 K6861199 12X
P RAND CHRK 2011 RUNNN BARDS STRBS ATRAS TUBUARS MARCHPDS TUBUARS Front Double 8mm 8mm 1.5" 6mm 8mm 3X 3X 3X 9X 3X 3X 6X 6X 12X 3X Front Double H 8mm 8mm 1.5" 6mm 8mm 3X 3X 3X 9X 3X 3X 6X 6X 12X 3X 1 of
Más detallesJEEP WRANGLER & WRANGLER UNLIMITED Sun Bonnet
JEEP WRNGLER & WRNGLER UNLIMITED Sun onnet 82214320 82214676 8-27-14 65526 Rev. 1 of 5 K6862100 JEEP WRNGLER & WRNGLER UNLIMITED Sun onnet 6-19-12 65526 Rev. 1 2 of 5 K 1X 4X D E 1X F T-25 Torx Ratchet
Más detallesH-5714 3-TIER DISPLAY TABLE
H-5714 3-TIER DISPLAY TABLE 1-800-295-5510 uline.com Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. TOOLS NEEDED Allen Wrench (Included) Phillips Screwdriver PARTS LIST Bottom
Más detallesProcess Control Work Instructions Control de Procesos Instrucciones de Trabajo. for / para
Process Control Work Instructions Control de Procesos Instrucciones de Trabajo for / para 629096898 VFCB Kit Relay Cable Harness Assy Ensamblar el Kit del Arnés de Cables del Relevador Publication Number:
Más detallespipe line clothing rack support à vêtements pipe line pipe line perchero
! Do not throw away packaging materials until assembly is complete.! Assemble this item on a soft surface, such as cardboard or carpet, to protect finish.! Proper assembly of this item requires 2 people
Más detalles"A" "B" "C" "D" "E" "F" "G"
Workbench with Riser Shelf and Backpanel Assembly Instructions R Fasteners (Shown full size) 12.7mm 3/8" 9.52mm 12.7mm 5/8" 15.87mm 12.7mm 1" 25.4mm 1/4" 6.35mm Quantity Type 54 8 40 14 4 4 8 "B" "D" "E"
Más detallesMessina TM 4 - Piece Sectional Loveseat, Sofa, & Corner Table
Page 1 of 7 Assembly Instructions Messina TM 4 - Piece Sectional Loveseat, Sofa, & Corner Table Model #: 523125 Thank you for purchasing this quality product. Be sure to check all packing materials carefully
Más detallesLAPTOP DESK WITH 3 BINS MESA PARA COMPUTADORA PERSONAL CON 3 CONTENEDORES
MODEL: 11222775R / MODELO: 11222775R LAPTOP DESK WITH 3 BINS MESA PARA COMPUTADORA PERSONAL CON 3 CONTENEDORES NO A B C D E F G H 1 2 3 4 5 6 7 8 9 PARTS AND HARDWARE LISTA DE PARTES Y HARDWARE TOP PANEL
Más detallesπ H-2561 Parts Assembly 1-800-295-5510 uline.com Tools needed H-2562 rectangular picnic table
π H-2561 H-2562 rectangular picnic table 1-800-295-5510 uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. Tools needed 3/4" (19mm) Socket Wrench Power Drill 3/8" (10mm)
Más detallesProMaster B-Pillar Grab Handle
ProMaster B-Pillar Grab Handle www.mopar.com Call Out Description Quantity Service Part Part Number (Y/N) Handle Reinforcement Bracket N Right B-Pillar Handle N Drilling Template N Handle Spacer N Handle
Más detalles2 (For some optional presser feet) 1. Raise needle and presser foot. 2. Remove the needle. 3. Loosen presser foot screw (1) and remove presser foot with shank (2), guiding it toward you and to the right.
Más detallesMODEL: 11222895 / MODELO: 11222895 COMPUTER DESK ESCRITORIO DE COMPUTADORA
MODEL: 222895 / MODELO: 222895 COMPUTER DESK ESCRITORIO DE COMPUTADORA NO 2 3 4 5 6 7 8 9 PARTS LIST AND HARDWARE LISTA DE PARTES Y ACCESORIOS HARDWARE LIST LISTA DE PARTES Y ACCESORIOS CHIPBOARD SCREW
Más detallesMid Century Mini Desk Mini Bureau Mid century Mini Escritorio Medio Siglo Assembly instructions Instructions d assemblage Instrucciones de ensamblaje
! Do not throw away packaging materials until assembly is complete.! To protect the finish, assemble this item on a soft surface, such as cardboard or carpet.! 2 People are required for proper assembly
Más detallesGARMENT STORAGE CENTER WITH SHELVES PARTS ASSEMBLY. uline.com POST ASSEMBLY TO INSTALL OPTIONAL CASTERS TO INSTALL SELF-LEVELERS
Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. π H-2449 1-800-295-5510 GARMENT STORAGE uline.com CENTER WITH SHELVES PARTS Connector x 6 36 x 18" Shelf x 1 18 x 18" Shelf x 12
Más detallesflat bar storage desk buffet de rangement plat escritorio de barras planas para almacenaje Parts
! Tools required:! Do not throw away packaging materials until assembly is complete.! ssemble this item on a soft surface, such as cardboard or carpet, to protect finish.! Proper assembly of this item
Más detallesessentialhome TM OWNER'S MANUAL
essentialhome TM OWNER'S MANUAL Grayson Armoire 5534309KP caution carefully read instructions and procedures for safe operation product code 0-06145331-2 upc code 0-2998655341-6 date of purchase / / receipt
Más detalles1 Spare Tire FIAT 500 A B C D F G H I CALL OUT DSCRIPTION QUANTITY A Winch Assembly 1 B Left Tire Bracket 1 C Right Tire Bracket 1 CALL OUT DSCRIPTION QUANTITY F Wheel Lock Knob 1 G Jack Kit Bag 1 H Spare
Más detallesπ H-4289 1-800-295-5510 uline.com TOOLS NEEDED H-4807 SINGLE TIER LOCKER
π H-89 H-80 SINGLE TIER LOCKER 1-800-9-10 uline.com Para Español, vea páginas -8. Pour le français, consulter les pages 9-1. TOOLS NEEDED 8mm Wrench (included) /8" Wrench (included) Phillips Screwdriver
Más detallesT87 Range Stops INSTALLATION APPLICATION INSTALLATION INSTRUCTIONS EFS
T87 Range Stops APPLICATION Use the 0144-001 range stops with the T87K, N thermostats to limit the minimum and maximum temperature settings. The 0144-001 contains two range stop scales and two #2-28 x
Más detallesUSA/Canada: 1-800-4KOHLER México: 001-800-456-4537 kohler.com 2011 Kohler Co.
Installation Guide Guide d installation Guía de instalación Cabinet Mounted Stereo Stéréo montée sur armoire Estereo de montaje en gabinete K-2958 M product numbers are for Mexico (i.e. K-12345M) Los números
Más detallesVANITY COMBO MEUBLE-LAVABO COMBINÉ JUEGO DE TOCADOR
Product Codes Codes de produit Códigos de los productos COC25, COE25, COW25, COCT86, COET86, COWT86, COCT28, COET28, COWT28, COCT08, COET08, COWT08, Effective Date: 02-27-08 Date d entrée en vigueur :
Más detallesπ H-4039 SPILL CONTAINMENT WORKSTATION CONNECTORS ASSEMBLY 1-800-295-5510 uline.com TOOL NEEDED
π H-4039 SPILL CONTAINMENT WORKSTATION CONNECTORS uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. TOOL NEEDED Plastic or Rubber Mallet ASSEMBLY 1. Locate one of the
Más detallesMeijer.com A
English MULTI-FUNCTIONL COMPUTER TLE SSEMLY INSTRUCTION Meijer.com C MODEL RT - 350 IMPORTNT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not
Más detallesPlastic restrain Plastic wall bra
Plastic restrain Plastic wall bra Long wood scr Short wood sc! Do not throw away packaging materials until assembly is complete.! To protect the finish, assemble this item on a soft surface, such as cardboard
Más detallesSmart Seat Buckle Replacement Guide
Smart Seat Buckle Replacement Guide 2014 Graco PD272023A 2/14 To Remove Existing Harness Tongues and Buckle and Attach Replacement Buckle 1 2 Remove seat from base. Loosen straps by lifting lever and pull
Más detallesParts/Pièces/Herrajes
4 : 5! " # $ % & ' & ' % ( $! % ) % * %! " # + ', -! Parts/Pièces/Herrajes. / ( ) ) 0! 1 ( ) 0! 1 2 3 ( ) 0! 1 6 ) 7 ) ( 7 ) 6 ) ; " ( 7 6 ) 8 9 ( 7 6 ) ( 7 6 ) ) Headboard 1x Tête de lit 1x Cabecera 1x
Más detallesChrome Door Handles DODGE DART K B Door Handle Grip. CALL OUT DESCRIPTION QUANTITY A Door Handle Base 3. 4 C Driver Side Door Handle Base 1
1 Chrome Door Handles DODGE DRT C CLL OUT DESCRIPTION QUNTITY Door Handle ase 3 Door Handle Grip 4 C Driver Side Door Handle ase 1 Right ngle Pry Tool TOOLS REQUIRED T-20 Torx Driver Flathead Screwdriver
Más detallesUniversal Mount for LCD, LED & Plasma TV s
Tilt Mount MTMK & LTMK Soporte Universal Inclinable para TV s de LCD, LED y Plasma Support Universel Inclinaison pour TV LCD, LED et Plasma Soporte Universal Inclinavel para TV s de LCD / LED / Plasma
Más detallesπ H-4756 TIP AND ROLL KIT FOR 4-ROW BLEACHERS PARTS 1-800-295-5510 uline.com TOOLS NEEDED
π H-4756 TIP AND ROLL KIT FOR 4-ROW BLEACHERS uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. WARNING! Due to outdoor wind hazards, bleachers with tip and roll kits,
Más detallesModel/Modelo: SR42UBEVS
SmartRack Assembly Instructions Instrucciones de Ensamble del SmartRack Model/Modelo: SRUBEVS West 35th Street, Chicago, IL 60609 USA www.tripplite.com/support Copyright 03 Tripp Lite. All trademarks are
Más detalles2.4L ENGINE BLOCK HEATER CHRYSLER 200 / DODGE AVENGER. www.mopar.com 1. CALL OUT DESCRIPTION QUANTITY 1 Engine Block Heater 1 2 Cord 1 3 Tie Straps 2
www.mopar.com 1 2.4L ENGINE BLOCK HEATER CHRYSLER 200 / DODGE AVENGER CALL OUT DESCRIPTION QUANTITY 1 Engine Block Heater 1 2 Cord 1 3 Tie Straps 2 TOOLS REQUIRED Front End Cutters Flat Bladed, Phillips
Más detallesASSEMBLY INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE ENSAMBLAJE
an LI ompany New Hope, MN 55428 www.safcoproducts.com SSMLY INSTRUTIONS INSTRUTIONS MONTG INSTRUIONS NSML 1857 Impromptu Machine Stand Meuble pour appareils de bureau stante para máquinas de oficina PROUT
Más detallesGarden Dump Cart. Owners Manual. 1-year Limited Warranty. Model GOR108D-SC
Garden Dump Cart Owners Manual Model GOR108D-SC Important Safety Instructions Assembly Instructions Parts and Hardware Identification U.S. Patent #s 6,851,756, 7,210,697 and 7,390,065 Other U.S. and Foreign
Más detallesJUEGO DE SOPORTE PARA PARED DE ACERO FUNDIDO PARA ARMARIO ALTO Y ARMARIO PARA HERRAMIENTAS
WELDED-STEEL TLL GEROX & GERLOCKER RCKET KIT Installation Instructions JUEGO DE SOPORTE PR PRED DE CERO FUNDIDO PR RMRIO LTO Y RMRIO PR HERRMIENTS Instrucciones de instalación ENSEMLE DE SUPPORTS MURUX
Más detallesEste mueble puede caerse por encima causando daño serio o la muerte
A Dorel Company MERIWOOD TM INDUSTRIES 3597318PCOM ALTO STOP ARRÊT DO NOT RETURN PRODUCT TO THE STORE Individual stores do not stock parts. NO REGRESAS ESTA PRODUCTO A LA TIENDA Las tiendas no tiene partes.
Más detallesπ H-2888 RECYCLED PLASTIC BENCH WITH BACK parts 1-800-295-5510 uline.com TOols NEEDED
π H-2888 RECYCLED PLASTIC BENCH WITH BACK uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. TOols NEEDED 7/16" Socket Wrench or 7/16" Drill and Socket Bit parts Single
Más detallesTrim Frame Surrounding Door Front Panel ( 3/4" Max.)
ecorator imensions and Installation. Type Thickness Front 17-3/4 (451mm) 44-1/8 (1121mm) 24 (610mm) 35-3/4 (908mm) 3/4 max (19mm) Spacer 16-3/4 (425mm) 43-3/16 (1097mm) 23 (584mm) 34-3/4 (883mm) 1/16 (2mm)
Más detalles1 Chrome Mirror Trim Cap JEEP GRAND CHEROKEE A CALL OUT DESCRIPTION QUANTITY A Chrome Mirror Trim Cap 2 CHROME MIRROR TRIM CAP REMOVAL WARNING: Always wear eye and hand protection when servicing the mirror
Más detalleswww.tricam.com 800-867-6763 7677 Equitable Drive Tricam PRECAUCIÓN: Antes de utilizar este producto, lea, comprenda y siga TODAS las instrucciones.
SC100-D manual 1/8/08 10:6 AM Page 1 1/08 Para preguntas acerca del producto: Tricam 7677 Equitable Drive Eden Prairie, MN 55344 800-867-6763 www.tricam.com PRECAUCIÓN: Antes de utilizar este producto,
Más detallesπ H-3905 PUSH FOAMING SOAP DISPENSER INSTALLATION 1-800-295-5510 uline.com MOUNTING INSTRUCTIONS APPLYING DISPENSER LABEL TOOLS NEEDED TAPE MOUNTING
π H-3905 PUSH FOAMING SOAP DISPENSER 1-800-295-5510 uline.com Para Español, vea páginas 4-6. TOOLS NEEDED Phillips Screwdriver Electric Drill INSTALLATION APPLYING DISPENSER LABEL 1. Peel label from backing.
Más detallesARLO CHANGER INSTRUCTIONS
ARLO CHANGER INSTRUCTIONS E Instrucciones para Vestidor Arlo GUARANTEE E Garantía de 4 años válida sólo en Reino Unido e Irlanda 11 (1) (2) (3) (4) (5) (6) (7) (8) 1 (9) (10) (11) (12) (13) A D B E C F
Más detallesOPERATOR S MANUAL. DANGER is used to indicate a hazardous situation which, if not avoided, will result in serious injury or death.
OPERATOR S MANUAL 6-FT. WORKBENCH SAFETY DANGER is used to indicate a hazardous situation which, if not avoided, will result in serious injury or death. WARNING indicates a hazardous situation which, if
Más detallesH-3594 CLEAR-VIEW CABINET
π H-35 CLEAR-VIEW CABINET 1-800-25-5510 uline.com Para Español, vea páginas -6. Pour le français, consulter les pages 7-. PRIMARY ASSEMBLY 6 2 1 7 5 8 3 PAGE 1 OF 0616 PH-35 π H-35 CLEAR-VIEW CABINET 1-800-25-5510
Más detallesMANUAL DE INSTRUCCIONES PARRILLA BARBACOA (18 ) ED-4047BQ
MANUAL DE INSTRUCCIONES PARRILLA BARBACOA (18 ) ED-4047BQ ESTIMADO CLIENTE Con el fin de que obtenga el mayor desempeño de su producto, por favor lea este manual de instrucciones cuidadosamente antes de
Más detalles4 SCREWPLUG SUP279 1/6 K CONTENTS Hood Protector Instructions Sheet Alcohol Wipe Screwplugs Large Screws Large Washers Rust Inhibitor
1/6 CONTENTS Hood Protector Instructions Sheet Alcohol Wipe Screwplugs Large Screws Large Washers Rust Inhibitor Abrasive Resistant Tape x3 IMPORTANT: Read all instructions carefully before beginning the
Más detallesTABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
LL CDDY ssembly Instructions ORGNIZDOR PR PELOTS Instrucciones de ensamblaje RÉCEPTCLE POUR LLONS Instructions d'assemblage TLE OF CONTENTS/ÍNDICE/TLE DES MTIÈRES INSTLLTION INSTRUCTIONS...2 all Caddy
Más detallesPara Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. π H-2805. 1-800-295-5510 uline.com CLEAR-VIEW CABINET PRIMARY ASSEMBLY
CLEAR-VIEW CABINET 1-800-295-55 uline.com Para Español, vea páginas -6. Pour le français, consulter les pages 7-9. PRIMARY ASSEMBLY 2 7 1 8 6 5 9 3 PAGE 1 OF 9 CLEAR-VIEW CABINET 1-800-295-55 uline.com
Más detallesInstallation Instructions
Installation Instructions I- Sheet Number THX03 PART NUMBER: 34641334, 34641371, PRODUCT: Terrain HX Nerf step APPLICATION: 09-15 RAM 1500 Hardware Kit Contains Recommended Tools (14) 3/8" x 1" Hex Bolts
Más detalles3PIECES KIDS TABLE SET JUEGO DE MESA PARA NIÑOS DE 3 PIEZAS
MODEL: 11224487 / MODELO: 11224487 3PIECES KIDS TABLE SET JUEO DE MESA PARA NIÑOS DE 3 PIEZAS NO A B C D E F PARTS LIST AND ARDWARE LISTA DE PARTES Y ACCESORIOS ARDWARE LIST LISTA DE ACCESORIOS TABLE TOP
Más detalles#10 x 3-in Washer Head Screw #8 x 3/4-in Truss Head Screw
Floating Shelf 2-ct #6 x 3/4-in Screw Wood Mounting Plate 2-ct Metal Bracket 4-ct 4-ct #10 x 3-in Washer Head Screw #8 x 3/4-in Truss Head Screw Floating Shelf Floating Shelf Includes: 1-ct - Floating
Más detalles*P516-911* L400 Lock with Indicator
*P516-911* L400 Lock with Indicator P516-911 L400 Series Lock with Indicator Sectional Trim Installation Instructions Indicator trim is available for either the inside or outside of the door on allowable
Más detallesEste mueble puede caerse por encima causando daño serio o la muerte
A Dorel Company MERIWOOD TM INDUSTRIES 22402PCOM ALTO STOP ARRÊT DO NOT RETURN PRODUCT TO THE STORE Individual stores do not stock parts. NO REGRESAS ESTA PRODUCTO A LA TIENDA Las tiendas no tiene partes.
Más detallesAplicaciones con puntada recta 1 2 1. Raise needle and presser foot. 2. Remove the needle. 3. Loosen presser foot screw (1) and remove presser foot with shank (2), guiding it toward you and to the right.
Más detalles*P515-814* L/LV9000-Series. 2 All functions Todas las funciones Toutes fonctions. 1 All functions Todas las funciones Toutes fonctions
*P515-814* P515-814 Knob and Rose Perilla y Embellecedor Bouton et Rosette L/LV9000-Series Installation Instructions Instrucciones de Instalación Instructions d Installation A. Lockcase and mounting screws
Más detalles(for some optional presser feet) 2 1. Raise needle and presser foot. 2. Remove the needle. 3. Loosen presser foot screw (1) and remove presser foot with shank (2), guiding it toward you and to the right.
Más detallesInstructions for 444 Wall Unit Instrucciones para la unidad 444 Instructions pour l unité de 444 mur
Instructions for Wall Unit Instrucciones para la unidad Instructions pour l unité de mur Rev-A-Shelf, L.L.C. I-WC 09 Plantside Dr. Jeffersontown, KY 099 (800) 66-6 www.rev-a-shelf.com 0/07 Instructions
Más detallesTrapeze and Floor Stand. Potence et support sur pied. Trapecio y Pedestal. User Instruction Manual. Manuel de l utilisateur
Trapeze and Floor Stand Trapeze Model IC-7740, Floor Stand Model IC-7714 User Instruction Manual Potence et support sur pied Modèle de potence IC-7740, Modèle de support sur pied IC-7714 Manuel de l utilisateur
Más detallesH-2450 GARMENT STORAGE CENTER WITH BASKETS
H-2450 GARMENT STORAGE CENTER WITH BASKETS 1-800-295-5510 uline.com Para Español, vea páginas 5-8. Pour le français, consulter les pages 9-12. PARTS Connector x 6 18 x 18" Shelf x 6 36 x 18" Shelf x 1
Más detalles2005-07 Chrysler Town & Country Van (w/stow & Go Seating) 2005-07 Dodge Caravan and Grand Caravan (w/stow & Go seating)
August 2008 INSTALLATION INSTRUCTIONS Rev. 1 MODEL NO. 82770 75170 APPLICATION: 2005-07 Chrysler Town & Country Van (w/stow & Go Seating) 2005-07 Dodge Caravan and Grand Caravan (w/stow & Go seating) WARNING:
Más detallesINSTRUCTION MANUAL Smart Security Light
SPL06-07A1W1-BKT-K1 INSTRUCTION MANUAL Smart Security Light Questions, problems, or missing parts? Before returning to the store, call MAXIMUS customer service at 1-866-897-2098, Monday Friday, 9:30am
Más detallesSYSTEM INSTALLATION MANUAL MANUAL DE INSTALACIÓN
SYSTEM INSTALLATION MANUAL MANUAL DE INSTALACIÓN Measuring Tape Cinta métrica Ø 8 mm twist drill (wood) Broca espiral Ø 8 mm (para madera) Ø 14 mm stone drill (brick) Broca para piedra Ø14 mm (ladrillo)
Más detalles1-800-295-5510 uline.com. Phillips Screwdriver Mini Flathead Screwdriver Electric Drill 5/16" Drill Bit PARTS. Flat Display Wall Mount Bracket x 1
π H-2769, H-4665 TAKE-A-NUMBER-SYSTEM ADDITIONAL 2 AND 3-DIGIT LED DISPLAY 1-800-295-5510 uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. TOOLS NEEDED Phillips Screwdriver
Más detallesM8 x 16 (16 pcs.) M8 x 16 (32 pcs.) M8 x 20 (4 pcs.)
MODELS 8035 & 8035R SLIDE TOP UTILITY CART WaRNINGS, ASSEMBLY INSTRUCTIONS & PARTS BREAKDOWN Read and follow all instructions in User's Manual. It is the responsibility of the owner to make sure all personnel
Más detallesEste mueble puede caerse por encima causando daño serio o la muerte
COSCO 586932PCOM ALTO STOP ARRÊT DO NOT RETURN PRODUCT TO THE STORE Individual stores do not stock parts. NO REGRESAS ESTA PRODUCTO A LA TIENDA Las tiendas no tiene partes. NE RETOURNEZ PAS LE PRODUIT
Más detallesUniversal Steel Stand
R Universal Steel Stand ASSEMBLY INSTRUCTIONS Item# KRS1030 Tools Required: Square 1/2 Socket wrench & extension (2) 3/4 Open-end or adjustable wrenches Phillips head driver bit www.kregtool.com 800.447.8638
Más detallesActive Range of Motion Exercises: Wrists, Elbows, Forearms and Shoulders
Active Range of Motion Exercises: Wrists, Elbows, Forearms and Shoulders Repeat each exercise times, times a day. Do only the exercises that are checked. Do these exercises with: Both arms Right arm Left
Más detallesSP-U. Soporte colgado universal para JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15
Soporte colgado universal para JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15 Universal U-bracket for JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15 Copyright
Más detallesGOLF CADDY ORGANIZADOR PARA ARTÍCULOS DE GOLF ÉTAGÈRE À ACCESSOIRES DE GOLF. Assembly Instructions. Instrucciones de ensamblaje
GOLF DDY ssembly Instructions ORGNIZDOR PR RTÍULOS DE GOLF Instrucciones de ensamblaje ÉTGÈRE À ESSOIRES DE GOLF Instructions d assemblage IT'S TIME TO RETHINK THE GRGE. ES TIEMPO DE VOLVER PENSR EN EL
Más detallesMODEL/ MODÈLE/ MODELO: BG
16 SE SERIES SIDE LOCKER WITH 4 DRAWERS RANGEMENT LATÉRAL DE 40,6 cm À 4 TIROIRS DE SÉRIE SE ARMARIO LATERAL DE 16 PO CON 4 CAJONES DE SERIE SE MODEL/ MODÈLE/ MODELO: BG08041042 WARNING: 1. Close and lock
Más detalles4 SCREWPLUG SUP271 1/ K /16 or 5mm
1/6 CONTENTS Hood Protector Instructions Sheet Alcohol Wipe Screwplugs Large Screws Large Washers Rust Inhibitor Metal Wing Clips Nut Inserts Small Screws Small Washers Abrasive Resistant Tape IMPORTANT:
Más detallesWith Flange: 1/2" Copper pipe stub-out length from finished wall surface
Stub out length for tub spouts (measured from finished wall surface) With Flange: 1/2" Copper pipe stub-out length from finished wall surface Without Flange: 1/2" Copper pipe stub-out length from finished
Más detallesINSTRUCTIONS FOR MODEL 4632
Quality Products for the way you live INSTRUCTIONS FOR MODEL 4632 IMPORTANT: PLEASE KEEP FOR FUTURE REFERENCE! For helpful tips and instructions, please visit our website: www.northstatesind.com or contact
Más detallesASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTI Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference. E 1 I ei M ij INSTRUCCIONES
Más detallesInstructivo de uso y cuidado del Aplicador de Implantes Lapisa. Productos Destacados
Instructivo de uso y cuidado del Aplicador de Implantes Lapisa Productos Destacados Diseño ergonómico Producido con materiales de larga duración para asegurar una vidá útil prolongada Espacio para aguja
Más detallesASSEMBLY INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE ENSAMBLAJE
an LDI Spaces Company inneapolis, 55428 www.safcoproducts.com SSEBLY ISTRUCTIS ISTRUCTIS DE TGE ISTRUCCIES DE ESBLJE 1936 Xpressions Desk with Shelf Bureau avec étagère Escritorio con estante SHW WITH
Más detallesZip & Zoom Pedal Car Voiture à pédale Zip & Zoom Coche a Pedal Rayo Rápido
Zip & Zoom Pedal Car Voiture à pédale Zip & Zoom Coche a Pedal Rayo Rápido The Step2 Company 10010 Aurora-Hudson Rd. Streetsboro, OH 44241 USA 1-800-347-8372 Valid only in U.S.A. and Canada Numéro disponible
Más detallesAuto Rain Lawn Gear LA
Auto Rain Lawn Gear LA01-5006 For LA02 and LA03 Same Basic Layout Description List Spigot (water source) 18315 100 Roll 3/4 Poly Pipe 1436-007 IXMP 3/4" Insert Male Adapter 9-1602 Brass 3/4" NHT X 1/2"
Más detallesBluetooth Keyboard And Stand Combo For ipad
Model: 50915 Bluetooth Keyboard And Stand Combo For ipad User s Manual Please read this User Manual carefully before you start to use the keyboard. 1. Package contents: 78 keys Bluetooth keyboard 1 pcs
Más detallesWARNING ATTENTION ATENCIÓN
MALM WARNING Serious or fatal crushing injuries can occur from furniture tip-over. ALWAYS secure this furniture to the wall using tip-over restraints. To further reduce the risk of serious injury and death
Más detallesHPFD12XCP, HPFD12XHP
HPFD12XCP, HPFD12XHP 1 2 3 4 1. Main window panel and extension panels (extends from 20 up to 46 )... 3 pieces 2. Exhaust nozzle with diameter 130mm...1 piece 3. Exhaust nozzle with diameter 110mm...1
Más detallesChevy Camaro 2010-up 82-3010
INSTALLATION INSTRUCTIONS FOR PART 82-3010 APPLICATIONS Chevy Camaro 2010-up 82-3010 KIT FEATURES Provides spacing for aftermarket speaker installation Table of Contents Door Panel Disassembly. Chevy Camaro
Más detallesThis Instruction Sheet contains IMPORTANT safety information. Please read and keep for future reference.
FULL SIZE TRUCK MULTI-FIT HITCH Model Number: 37096 Quick and Easy Installation Many NO DRILL Applications No Special Tools Required for Installation Unique OEM Protective Coating This Instruction Sheet
Más detallesINSTALLATION INSTRUCTION Vogue WS-3120
WS-3120 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance
Más detalles(2) #8-32 x 3/4 Phillips head self tapping screws
Keyed-in-Handle Auto Latch ECR Installation Instructions and Owner s Manual Wayne-Dalton, a Division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com Parts Breakdown All
Más detallesInstallation Instructions DODGE RAM PICKUP WITH OR WITHOUT O.E.M. HITCH
Installation Instructions WITH OR WITHOUT O.E.M. HITCH Part Numbers: 99 Hitch Shown In Proper Position Equipment Required: 00 short bed model hack saw Fastener Kit: F99 Wrenches: /, /, / Drill Bits: /
Más detallesBEFORE BEGINNING AVANT DE COMMENCER ANTES DE EMPEZAR
Storage Bench Banc de Rangement Banco de Almacenaje INSTALLATION INSTRUCTIONS DIRECTIVES D INSTALLATION INSTRUCCIONES DE INSTALACIÓN BEFORE BEINNIN AVANT DE COMMENCER ANTES DE EMPEZAR Please read all instructions
Más detallesCap frame User s Guide Manuel d instructions du cadre pour casquettes Manual de instrucciones del bastidor de gorras
Cap frame User s Guide Manuel d instructions du cadre pour casquettes Manual de instrucciones del bastidor de gorras Table of Contents Cap frame and its accessories Preparing the mounting jig... For the
Más detallesROCK N STEREO SOUND DESK
Read and save these instructions ROCK N STEREO SOUND DESK RTA-M1102-BK INSTRUCTIONS TABLE OF CONTENTS PACKAGE INCLUDES Package Includes... 2 Specifications... 2 Product Parts List... 3 1 2 3 Product Details...
Más detallesASSEMBLY INSTRUCTIONS
2-Shelf Utility Cart MODEL NUMBER 5330 PARTS LIST LETTER CODE DESCRIPTION QTY. PART NO. A Base Plate 1 5330-07 B Swivel Caster 2 5330-26 C Thick Bolt 16 5330-22 D Large Washer 16 5330-21 E Large Nut 16
Más detallesMANUAL DE INSTRUCCIONES PARRILLA BARBACOA (14 ) ED-4045BQ
MANUAL DE INSTRUCCIONES PARRILLA BARBACOA (14 ) ED-4045BQ ESTIMADO CLIENTE Con el fin de que obtenga el mayor desempeño de su producto, por favor lea este manual de instrucciones cuidadosamente antes de
Más detallesRight Hinge Instructions Please turn poster over for Left Hinge Instructions.
202220566RF EV Extruded RH Installation Instructions Right Hinge Instructions Please turn poster over for Left Hinge Instructions. Instrucciones para la instalación Instrucciones para bisagras del lado
Más detallesBOB Revolution Duallie Strollers Instructions / Instructions / Instrucciones
BOB Revolution Duallie Strollers Seat Replacement What you will need: Phillips Screwdriver (1) Adjustable Wrench or (1) 8 mm Wrench and (1) 18 mm Wrench 4 mm Allen Wrench IMPORTANT: If you have a REVOLUTION
Más detallesApéndice B. Guía de instalación del estante
Apéndice B Guía de instalación del estante Este apéndice explica cómo instalar el estante opcional para el servidor Acer Altos G700. 105 Instalación del estante del sistema El servidor Altos G701 puede
Más detallesπ H-4694, H-4695 RIPACK HEAT GUN EXTENSION ATTACH EXTENSION 1-800-295-5510 uline.com
π H-4694, H-4695 RIPACK HEAT GUN EXTENSION uline.com Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. ATTACH EXTENSION 1. In order to use a Ripack Heat Gun Extension, you must
Más detallesWear It Right Wearing your elastomeric full face, 4 strap respirator
Wear It Right Wearing your elastomeric full face, strap respirator. Fully loosen all four head straps. Pull hair back with one hand. Bring facepiece up to face with other hand. Check the seal of your elastomeric
Más detallesComo desempacar el Time Attendant Además de ésta guía, el empaque debe incluír lo siguiente: Time Attendant Quick Install Reference Guide
Como desempacar el Time Attendant Además de ésta guía, el empaque debe incluír lo siguiente: Terminal para colectar datos Cable de comunicación Adaptador de 25 a 9-DB CD con Software Adaptador de Corriente
Más detallesCambridge Pre-Packaged / Pre-Cut Olde English Wall Mailbox
Note: Cap layer is not included in the kit and is sold separately. Nota: La capa del casquillo no se incluye en el kit y se vende por separado. Cambridge Pre-Envasados / Pre-Cortadas Olde Inglés Buzón
Más detalles