AX-ADMZ01. Mazda Data Interface
|
|
- Silvia Campos Maestre
- hace 6 años
- Vistas:
Transcripción
1 AX-ADMZ01 INSTALLATION INSTRUCTIONS Mazda Data Interface TABLE OF CONTENTS Connections to be made Installing the Axxess interface...4 Testing the Axxess interface...4 INTRODUCTION The AX-ADMZ01 is designed to and MUST be used with the AX-ADBOX1 or AX-ADBOX2 (sold seperately). Please refer to AX-ADBOX1 or AX-ADBOX2 for 16-pin connector with stripped leads. INTERFACE COMPONENTS AX-ADMZ01 harness TOOLS REQUIRED Cutting tool Crimping tool Tape Connectors (example: butt-connectors, bell caps, etc.) APPLICATIONS MAZDA CX CX CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. AxxessInterfaces.com COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/27/17 INSTAX-ADMZ01
2 CONNECTIONS TO BE MADE Attention! This interface will work with models that are either factory amplified, or nonamplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership. For models without an amplifier: From the 16-pin harness with stripped leads to the aftermarket radio: Connect the White wire to the left front positive speaker output. Connect the White/Black wire to the left front negative speaker output. Connect the Gray wire to the right front positive speaker output. Connect the Gray/Black wire to the right front negative speaker output. The following (3) wires are only for multimedia/navigation radios that require these wires. Connect the Blue/Pink wire to the VSS/speed sense wire. Connect the Green/Purple wire to the reverse wire. Connect the Light Green wire to the parking brake wire Only make the following connections if the vehicle is amplified. Connect the Green wire to the radio s left rear positive speaker output. Connect the Green/Black wire to the radio s left rear negative speaker output. Connect the Purple wire to the radio s right rear positive speaker output. Connect the Purple/Black wire to the radio s right rear negative speaker output. Tape off and disregard the following (8) wires, they will not be used in this application: Blue/White, Brown, Green, Green/Black, Orange/White, Purple, Purple/Black, Red From the AX-ADMZ01 harness to the aftermarket radio: Connect the Black wire to the ground wire. Connect the Yellow wire to the battery wire. Connect the Red wire to the accessory wire. If the aftermarket radio has an illumination wire, connect the Orange wire to it. Connect the Blue wire to the power antenna wire. Connect the Green wire to the radio s left rear positive speaker output. Connect the Green/Black wire to the radio s left rear negative speaker output. Connect the Purple wire to the radio s right rear positive speaker output. Connect the Purple/Black wire to the radio s right rear negative speaker output. Connect the Green/Purple wire to the reverse wire of the aftermarket navigation radio. Note: The 2 long harness with a 24-pin connector is a service harness for setting the clock with the factory radio. Please run this harness to a location where it can be easily accessed, yet hidden. Continue to 12-pin pre-wired ASWC-1 harness 2
3 CONNECTIONS TO BE MADE (CONT) Attention! This interface will work with models that are either factory amplified, or nonamplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership. For models with an amplifier: From the 16-pin harness with stripped leads to the aftermarket radio: Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier. Connect the Gray wire to the right front positive speaker output. Connect the Gray/Black wire to the right front negative speaker output. Connect the White wire to the left front positive speaker output. Connect the White/Black wire to the left front negative speaker output. Connect the Green wire to the left rear positive speaker output. Connect the Green/Black wire to the left rear negative speaker output. Connect the Purple wire to the right rear positive speaker output. Connect the Purple/Black wire to the right rear negative output. The following (3) wires are only for multimedia/navigation radios that require these wires. Connect the Blue/Pink wire to the VSS/speed sense wire. Connect the Green/Purple wire to the reverse wire. Connect the Light Green wire to the parking brake wire Tape off and disregard the following (3) wires, they will not be used in this application: Brown, Orange/White, Red From the AX-ADMZ01 harness to the aftermarket radio: Connect the Black wire to the ground wire. Connect the Yellow wire to the battery wire. Connect the Red wire to the accessory wire. Connect the Blue wire to the power antenna wire. If the aftermarket radio has an illumination wire, connect the Orange wire to it. Tape off and disregard the following (4) wires, they will not be used in this application: Green, Green/Black, Purple, Purple/Black Note: The 2 long harness with a 24-pin connector is a service harness for setting the clock with the factory radio. Please run this harness to a location where it can be easily accessed, yet hidden. Continue to 12-pin pre-wired ASWC-1 harness 12-pin pre-wired ASWC-1 harness: This harness is to be used along with the optional ASWC-1 (not included) to retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it will be used, please refer to the ASWC-1 instructions for radio connections and programming. Note: Disregard the harness that comes with the ASWC-1. REV. 9/27/2017 INSTAX-ADMZ01 3
4 AX-ADMZ01 INSTALLATION INSTRUCTIONS INSTALLING THE AXXESS INTERFACE Connect the 16-pin harness with stripped leads into the interface. Connect the AX-ADMZ01 harness into the interface, and then to the wiring harness in the vehicle. Note: If using the ASWC-1 (sold separately), connect it after you initialize and test the interface with the key in the off position. IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. TESTING THE AXXESS INTERFACE Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on. The factory amplifier should come on and you should hear sound at this point. Test all functions of the installation for proper operation, before reassembling the dash. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians AxxessInterfaces.com COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/27/17 INSTAX-ADMZ01
5 AX-ADMZ01 INSTRUCCIONES DE INSTALACIÓN Mazda Interfase de datos INDICE Conexiones que se deben hacer Instalación de la interfase Axxess...4 Prueba de la interfase Axxess...4 INTRODUCCIÓN El AX-ADMZ01 está diseñado y DEBE utilizarse con el AX-ADBOX1 o AX-ADBOX2 (se vende por separado). Consulte el AX-ADBOX1 o AX-ADBOX2 para obtener instrucciones para el conector de 16 pins con conectores pelados. COMPONENTES DE LA INTERFASE Arnés AX-ADMZ01 HERRAMIENTAS REQUERIDAS Herramienta de corte Pelacables Cinta Conectores (ejemplo: conectores de extremo, de campana, etc...) APLICACIONES MAZDA CX CX PRECAUCIÓN! Todos los accesorios, interruptores, paneles de controles de clima y especialmente las luces del indicador de las bolsas de aire deben estar conectados antes ciclar la ignición. Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. AxxessInterfaces.com COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/27/17 INSTAX-ADMZ01
6 CONEXIONES QUE SE DEBEN HACER Atención! Esta interfase funcionará con modelos que equipado con amplificador de fábrica o que no estén amplificados. Siga las instrucciones cuidadosamente para su modelo de vehículo. Ignorar las instrucciones ocasionará se producirá un sonido incorrecto. Si no sabe con seguridad Si su vehículo está equipado con un amplificador o no, comuníquese con su concesionario local. Para modelos sin un amplificador: Del arnés de 16 pins con conectores pelados al radio de mercado secundario: Conecte el cable blanco con la salida positiva de la bocina izquierda delantera. Conecte el cable blanco/negro con la salida negativa de la bocina izquierda delantera. Conecte el cable gris con la salida positiva de la bocina derecha delantera. Conecte el cable gris/negro con la salida negativa de la bocina derecha delantera. Los siguientes (3) cables son para radios con multimedios/navegación que incluyen estos cables. Conecte el cable azul/rosa al cable VSS o del sensor de velocidad. Conecte el cable verde/púrpura al cable de reversa. Conecte el cable verde claro al cable de freno de mano. Sólo hacer las siguientes conexiones si el vehículo se amplifica. Conecte el cable verde a la izquierda de salida positivo del altavoz posterior de la radio. Conecte el cable verde/negro a la izquierda salida negativa del altavoz posterior de la radio. Conecte el cable púrpura a la derecha la salida del altavoz positivo trasera de la radio. Conecte el cable púrpura/negro a derecha salida negativa del altavoz posterior de la radio. Encinte e ignore los siguientes (8) cables, ya que no se utilizarán en esta aplicación: azul/blanco, marrón, verde, verde/negro, anaranjado/blanco, púrpura, púrpura/negro, rojo Del arnés AX-ADMZ01 al radio de mercado secundario: Conecte el cable negro al cable de tierra. Conecte el cable amarillo al cable de la batería. Conecte el cable rojo con el cable de accesorios. Si la radio del mercado secundario tiene un cable de la iluminación, conecte el cable anaranjado a ella. Conecte el cable azul al cable de la antena eléctrica. Conecte el cable verde con la salida positiva de la bocina izquierda trasera. Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera. Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. Conecte el cable púrpura/negro con la salida negativa de la bocina derecha trasera. Conecte el cable verde/púrpura con el cable de reversa del radio con navegación de mercado secundario. Nota: El arnés de 2 de largo con un conector de 24 pines es un arnés de servicio para ajustar el reloj con la radio de fábrica. Por favor, ejecute este arnés a un lugar donde se puede acceder fácilmente, pero ocultos. Continúe con el arnés ASWC-1 precableado de 12 pins 2
7 CONEXIONES QUE SE DEBEN HACER (CONT) Atención! Esta interfase funcionará con modelos que equipado con amplificador de fábrica o que no estén amplificados. Siga las instrucciones cuidadosamente para su modelo de vehículo. Ignorar las instrucciones ocasionará se producirá un sonido incorrecto. Si no sabe con seguridad Si su vehículo está equipado con un amplificador o no, comuníquese con su concesionario local. Para modelos con un amplificador: Del arnés de 16 pins con conectores pelados al radio de mercado secundario: Conecte el cable azul/blanco al cable de encendido del amplificador. Este cable debe estar conectado para escuchar sonido del amplificador de fábrica. Conecte el cable gris con la salida positiva de la bocina derecha delantera. Conecte el cable gris/negro con la salida negativa de la bocina derecha delantera. Conecte el cable blanco con la salida positiva de la bocina izquierda delantera. Conecte el cable blanco/negro con la salida negativa de la bocina izquierda delantera. Conecte el cable verde con la salida positiva de la bocina izquierda trasera. Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera. Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. Conecte el cable púrpura/negro con la salida negativa de la bocina derecha trasera. Los siguientes (3) cables son para radios con multimedios/navegación que incluyen estos cables. Conecte el cable azul/rosa al cable VSS o del sensor de velocidad. Conecte el cable verde/púrpura al cable de reversa. Conecte el cable verde claro al cable de freno de mano. Encinte e ignore los siguientes (3) cables, ya que no se utilizarán en esta aplicación: marrón, anaranjado/blanco, rojo Del arnés AX-ADMZ01 al radio de mercado secundario: Conecte el cable negro al cable de tierra. Conecte el cable amarillo al cable de la batería. Conecte el cable rojo con el cable de accesorios. Conecte el cable azul al cable de la antena eléctrica. Si la radio del mercado secundario tiene un cable de la iluminación, conecte el cable anaranjado a ella. Encinte e ignore los siguientes (4) cables, ya que no se utilizarán en esta aplicación: verde, verde/negro, púrpura, púrpura/negro Nota: El arnés de 2 de largo con un conector de 24 pines es un arnés de servicio para ajustar el reloj con la radio de fábrica. Por favor, ejecute este arnés a un lugar donde se puede acceder fácilmente, pero ocultos. Continúe con el arnés ASWC-1 precableado de 12 pins Arnés ASWC-1 precableado de 12 pins: Este arnés se debe usar junto con el ASWC-1 opcional (no incluido) para retener los controles de audio en el volante. Si no se va a usar el ASWC-1, ignore este arnés. Si se va a utilizar, consulte las instrucciones de ASWC-1 para las conexiones del radio y la programación. Nota: Ignore el arnés que viene con el ASWC-1. REV. 9/27/2017 INSTAX-ADMZ01 3
8 AX-ADMZ01 INSTRUCCIONES DE INSTALACIÓN INSTALACIÓN DE LA INTERFASE AXXESS Conecte el arnés de 16 pins con conectores pelados a la interfase. Conecte el arnés AX-ADMZ01 a la interfase, y luego al arnés de cableado del vehículo. Nota: Si va a utilizar el ASWC-1 (se vende por separado), conéctelo después de inicializar y probar la interfase, con la llave en la posición de apagado. IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar. PRUEBA DE LA INTERFASE AXXESS Gire la llave (o pulsar para botón de inicio) a la posición de encendido y esperar hasta que la radio se enciende. El amplificador de fábrica debe encenderse y usted debe oír el sonido en este punto. Pruebe todas las funciones de la instalación para su correcto funcionamiento, antes de volver a montar el tablero. EL CONOCIMIENTO ES PODER Mejore sus habilidades de instalación y fabricación inscribiéndose en la escuela de dispositivos electrónicos móviles más reconocida y respetada de nuestra industria. Regístrese en o llame al para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). AxxessInterfaces.com COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/27/17 INSTAX-ADMZ01
AX-CH013 Chrysler CAN data interface 2004-up
Installation instructions for part Chrysler CAN data interface 2004-up Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Provides NAV outputs (parking brake, reverse,
Más detallesBX-MB1 Mercedes CAN Bus Interface 2001-up
Installation instructions for part BX-MB1 BX-MB1 Mercedes CAN Bus Interface 2001-up FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Provides NAV outputs (parking
Más detallesHyundai Accent with radio delete 2012-2013 Table of Contents 99-7348B Dash Disassembly... 2
Installation instructions for part 99-7348B KIT FEATURES ISO DDIN radio provision ISO DIN radio provision with pocket Painted black to match factory finish KIT COMPONENTS A) Radio trim panel B) Radio brackets
Más detallesKia Forte 2014-up B Dash Disassembly Kia Forte 2014-up... 2 Kit Assembly Double DIN radio provision... 3.
INSTALLATION INSTRUCTIONS FOR PART 95-7356B KIT FEATURES Double DIN radio provision Painted matte black APPLICATIONS Kia Forte 2014-up Table of Contents 95-7356B Dash Disassembly Kia Forte 2014-up... 2
Más detallesJeep Liberty 2002-2007 95-6524B
INSTALLATION INSTRUCTIONS FOR PART 95-6524B KIT FEATURES Double DIN radio provision Painted matte black APPLICATIONS Jeep Liberty 2002-2007 95-6524B Table of Contents Dash Disassembly Jeep Liberty 2002-2007...
Más detallesNITO-01 Nissan Maxima 2016-up Amplifier Interface
Installation instructions for part Nissan Maxima 2016-up Amplifier Interface Provides accessory power (12-volt 10-amp) Provides NAV outputs (parking brake, reverse, and speed sense) Pre-wired ASWC-1 harness
Más detallesCHTO-02 Chrysler/Dodge amplified data interface 2002-2008
Installation instructions for CHTO-02 CHTO-02 Chrysler/Dodge amplified data interface 2002-2008 INTERFACE COMPONENTS CHTO-02 interface 16-pin harness with stripped leads 14-pin harness to 22-pin Chrysler
Más detallesXSVI-6523-NAV Chrysler Data Interface 2013-up
Installation instructions for part XSVI-6523-NAV REV. 7/7/2016 INSTXSVI-6523-NAV XSVI-6523-NAV Chrysler Data Interface 2013-up INTERFACE FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P.
Más detallesHyundai Genesis Coupe
INSTALLATION INSTRUCTIONS FOR PART 95-7336 APPLICATIONS Hyundai Genesis Coupe 2.0 2010-2011 (For models equipped with auto climate control and without OE navigation) 95-7336B, 95-7336S KIT FEATURES Double
Más detallesHyundai Elantra 2007-2010 (US Model Only) (Non Radio Delete) (Non Touring Model) 95-7326
Installation instructions for part 95-7326 Hyundai Elantra 2007-2010 (US Model Only) (Non Radio Delete) (Non Touring Model) 95-7326 Table of Contents Dash Disassembly... 2 Kit Assembly. ISO DDIN radio
Más detallesInstallation instructions for part LC-GMRC-LAN-01. Retains all warning chimes High level speaker input Retains balance and fade Micro B USB updatable
Installation instructions for part LC-GMRC-LAN-01 REV. 8/2/2016 INSTLC-GMRC-LAN-01 Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Provides NAV outputs (parking BUICK
Más detallesHyundai Veloster Blue Link interface 2011-up
INSTALLATION INSTRUCTIONS FOR PART HYBL-05 HYBL-05 Hyundai Veloster Blue Link interface 2011-up INTERFACE COMPONENTS HYBL-05 Interface 16-pin harness with stripped leads 18-pin to 24- & 18-pin connector
Más detallesChrysler/Dodge amplified data interface 2004-2007
INSTALLATION INSTRUCTIONS FOR PART CHTO-02 CHTO-02 Chrysler/Dodge amplified data interface 2004-2007 INTERFACE COMPONENTS CHTO-02 interface 16-pin harness with stripped leads 14-pin harness to 22-pin Chrysler
Más detallesHyundai Veloster 2012-up 95-7350B
INSTALLATION INSTRUCTIONS FOR PART 95-7350B APPLICATIONS Hyundai Veloster 2012-up 95-7350B KIT FEATURES Double DIN head unit provision Painted Matte Black KIT COMPONENTS A) Radio Trim Panel B) Brackets
Más detallesUniversal CF-104UD, SEA/HOS, SEA/HOS-W
INSTALLATION INSTRUCTIONS FOR PART 99-9000 KIT FEATURES DIN head unit provision Various mounting depths APPLICATIONS Universal 99-9000 CF-104UD, SEA/HOS, SEA/HOS-W Table of Contents Dash Disassembly All
Más detalles. GM full-size trucks and SUV s 1999-2002
INSTALLATION INSTRUCTIONS FOR PART DP-3002B KIT FEATURES Double DIN radio provision Painted scratch resistant matte black APPLICATIONS GM full-size trucks and SUV s 1999-2002 (models with message center
Más detallesToyota Avalon 2011-2012 (without factory navigation) 99-8233B
Installation instructions for part 99-8233B KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted Matte Black Toyota Avalon 2011-2012 (without factory navigation) 99-8233B Table
Más detallesISO radio provision with pocket... 3 ISO radio provision with pocket Painted Matte Black
INSTALLATION INSTRUCTIONS FOR PART 99-7354B APPLICATIONS Hyundai Santa Fe 2013-up Table of Contents 99-7354B Dash Disassembly Hyundai Santa Fe 2013-up... 2 Kit Assembly KIT FEATURES ISO radio provision
Más detallesKia Sorento 2016-up 99-7366B
Installation instructions for part 99-7366B KIT FEATURES ISO DIN radio provision with pocket Painted scratch resistant black Kia Sorento 2016-up 99-7366B Table of Contents Dash Disassembly... 2 Kit Preparation...
Más detallesHyundai Accent 2012-up 99-7347B
INSTALLATION INSTRUCTIONS FOR PART 99-7347B APPLICATIONS Hyundai Accent 2012-up 99-7347B KIT FEATURES ISO DIN head unit provision with pocket Double DIN head unit provisions Painted Black to match factory
Más detallesDodge Durango 2011-2013 Jeep Grand Cherokee 2011-2013 95-6513B
INSTALLATION INSTRUCTIONS FOR PART 95-6513B Dodge Durango 2011-2013 Jeep Grand Cherokee 2011-2013 95-6513B KIT FEATURES Double DIN radio provision Painted matte black to match factory Table of Contents
Más detallesLincoln Continental
INSTALLATION INSTRUCTIONS FOR PART 99-5809 APPLICATIONS Lincoln Continental 1998-2002 99-5809 KIT FEATURES DIN head unit provision with pocket ISO DIN head unit provision with pocket KIT COMPONENTS A)
Más detallesFord Escort/Escort ZX2 1997-2002/ ZX2 2001-2003, Mercury Tracer 1997-1999 99-5720
INSTALLATION INSTRUCTIONS FOR PART 99-5720 APPLICATIONS Ford Escort/Escort ZX2 1997-2002/ ZX2 2001-2003, Mercury Tracer 1997-1999 99-5720 KIT FEATURES DIN radio provision Incorporates factory climate controls
Más detallesJeep Renegade 2015-up 95-6532B
Installation instructions for part 95-6532B Jeep Renegade 2015-up 95-6532B Table of Contents Dash Disassembly... 2 Kit Assembly. ISO DDIN radio provision... 3 KIT FEATURES ISO DDIN radio provision Painted
Más detallesHyundai Elantra 2011-2013 99-7346B
Installation Instructions for 99-7346B Hyundai Elantra 2011-2013 99-7346B KIT FEATURES Double DIN radio provision ISO DIN radio provision with pocket Painted black to match factory finish Dash Disassembly
Más detallesFiat 500L 2014-up 95-6521B
Installation instructions for part 95-6521B KIT FEATURES DDIN radio provision Painted scratch-resistant matte black Fiat 500L 2014-up 95-6521B Table of Contents Dash Disassembly. Fiat 500L 2014-up... 2
Más detallesMitsubishi amplifier interface 2007-2013
INSTALLATION INSTRUCTIONS FOR PART MITO-02 MITO-02 Mitsubishi amplifier interface 2007-2013 INTERFACE COMPONENTS MITO-02 interface MITO-02 harness 14-pin harness with stripped leads and RCA jacks APPLICATIONS
Más detallesGMOS-045 Chevrolet Cruze 2011-2015 / Cruze Limited 2016 (with color screen)
Installation instructions for part GMOS-045 REV. 6/16/2016 INSTGMOS-045 GMOS-045 Chevrolet Cruze 2011-2015 / Cruze Limited 2016 (with color screen) FEATURES Provides accessory power (12-volt 10-amp) Retains
Más detallesINSTALLATION INSTRUCTIONS FOR PART 99-7341B APPLICATIONS 2010 HYUNDAI TUCSON
INSTALLATION INSTRUCTIONS FOR PART 99-74B KIT FEATURES KIT COMPONENTS APPLICATIONS 00 HYUNDAI TUCSON 99-74B ISO DIN Head Unit Provision With Pocket DDIN Head Unit Provision Painted Matte Black To Match
Más detallesHyundai Entourage 2007-2008 Kia Sedona 2006-2014 95-7323
INSTALLATION INSTRUCTIONS FOR PART 95-7323 KIT FEATURES Double DIN radio provision Hyundai Entourage 2007-2008 Kia Sedona 2006-2014 95-7323 Table of Contents Dash Disassembly Hyundai Entourage 2007-2008...Kia
Más detallesHYUNDAI TUCSON (without 4.3 screen) 2010-UP 99-7341B
Installation instructions for part 99-7341B HYUNDAI TUCSON (without 4.3 screen) 2010-UP 99-7341B KIT FEATURES ISO DIN Head Unit Provision With Pocket DDIN Head Unit Provision Painted Matte Black to match
Más detallesKia Soul 2010-2011 95-7337B
INSTALLATION INSTRUCTIONS FOR PART 95-7337B APPLICATIONS Kia Soul 2010-2011 95-7337B KIT FEATURES Double DIN head unit provision Stacked ISO head unit provision Painted matte black KIT COMPONENTS A) Double
Más detallesSuzuki Grand Vitara 2006--up 95-7953
INSTALLATION INSTRUCTIONS FOR PART 95-7953 APPLICATIONS Suzuki Grand Vitara 2006--up 95-7953 KIT FEATURES Double DIN radio provision Stacked ISO mount units provision KIT COMPONENTS A) Radio housing B)
Más detallesKia Sportage 2011-2016 95-7344G, 95-7344CH
Installation instructions for part 95-7344 Kia Sportage 2011-2016 95-7344G, 95-7344CH KIT FEATURES ISO DDIN radio provision Painted Gray or Charcoal to match factory finish G = Gray, CH = Charcoal Table
Más detallesMitsubishi amplifier interface 2006-2012
INSTALLATION INSTRUCTIONS FOR PART MITO-01 MITO-01 Mitsubishi amplifier interface 2006-2012 INTERFACE COMPONENTS MITO-01 interface MITO-01 harness 14-pin harness with stripped leads and RCA jacks 2-pin
Más detallesHonda Fit 2015-up 95-7883HG
INSTALLATION INSTRUCTIONS FOR PART 95-7883HG APPLICATIONS Honda Fit 2015-up 95-7883HG Table of Contents Dash Disassembly Honda Fit 2015-up... 2 KIT FEATURES Double DIN radio provision Painted high gloss
Más detallesToyota amplified interface 2001-up
INSTALLATION INSTRUCTIONS FOR PART TYTO-01 TYTO-01 Toyota amplified interface 2001-up INTERFACE COMPONENTS TYTO-01 interface 16-pin harness with stripped leads 14-pin to 20-pin harness with stripped leads
Más detallesLC-GMRC-CL29 GM Class-2/LAN-29 Data Bus Interface 2000-up
Installation instructions for part LC-GMRC-CL29 LC-GMRC-CL29 GM Class-2/LAN-29 Data Bus Interface 2000-up FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory power) Retains
Más detallesHyundai Genesis Coupe 2013-up 95-7352B
INSTALLATION INSTRUCTIONS FOR PART 95-7352B KIT FEATURES DDIN radio provision Painted Matte Black APPLICATIONS Hyundai Genesis Coupe 2013-up 95-7352B Table of Contents Dash Disassembly Hyundai Genesis
Más detallesHyundai Santa Fe 2007-2012
INSTALLATION INSTRUCTIONS FOR PART 99-7325 KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket APPLICATIONS Hyundai Santa Fe 2007-2012 (not for factory equipped NAV models) 99-7325
Más detallesPontiac Firebird 1993-2002 95-3312G
Installation Instructions for 95-3312G KIT FEATURES Double DIN radio provision Painted dark gray APPLICATIONS Pontiac Firebird 1993-2002 95-3312G Table of Contents Dash Disassembly. Pontiac Firebird 1993-2002...
Más detallesHyundai multi-kit 2001-2008 99-7313
INSTALLATION INSTRUCTIONS FOR PART 99-7313 APPLICATIONS See application list inside Hyundai multi-kit 2001-2008 99-7313 KIT FEATURES DIN Head Unit Provision with Pocket KIT COMPONENTS A) Radio Housing
Más detallesToyota/Scion multi-application 6 to 6.75 speaker adapter
INSTALLATION INSTRUCTIONS FOR PART 82-8148 APPLICATIONS (see chart inside for specific applications) Toyota/Scion multi-application 6 to 6.75 speaker adapter 82-8148 KIT FEATURES Provides spacing for aftermarket
Más detallesToyota Corolla 2009-2013 95-8223/95-8223S
INSTALLATION INSTRUCTIONS FOR PART 95-8223 KIT FEATURES Double DIN radio provision Painted to match factory dash 95-8223 = Black, 95-8223S = Silver APPLICATIONS Toyota Corolla 2009-2013 95-8223/95-8223S
Más detallesHyundai Genesis Coupe 2.0 2010-2012
INSTALLATION INSTRUCTIONS FOR PART 95-7339 APPLICATIONS Hyundai Genesis Coupe 2.0 2010-2012 (For models equipped with manual climate control) 95-7339B, 95-7339S KIT FEATURES Double DIN radio provision
Más detallesChrysler vehicles 2007-up
Installation instructions for CHTO-03 CHTO-03 Chrysler vehicles 2007-up INTERFACE COMPONENTS CHTO-03 Interface 16-pin harness with stripped leads 10-pin harness to 22-pin Chrysler harness with stripped
Más detalles2011 Hyundai Sonata Limited (without navigation) 99-7343
INSTALLATION INSTRUCTIONS FOR PART 99-7343 APPLICATIONS 2011 Hyundai Sonata Limited (without navigation) 99-7343 KIT FEATURES ISO DIN radio provision with pocket Double DIN radio provision Painted black
Más detallesToyota Avalon 2000-2004 95-8211
Installation instructions for part 95-8211 KIT FEATURES ISO DDIN radio provision Toyota Avalon 2000-2004 95-8211 Table of Contents Dash Disassembly. Column shift models... 2. Console shift models... 3
Más detallesChevy Camaro 2010-up 82-3010
INSTALLATION INSTRUCTIONS FOR PART 82-3010 APPLICATIONS Chevy Camaro 2010-up 82-3010 KIT FEATURES Provides spacing for aftermarket speaker installation Table of Contents Door Panel Disassembly. Chevy Camaro
Más detallesChrysler vehicles 2004-up
INSTALLATION INSTRUCTIONS FOR PART CHTO-013 CHTO-013 Chrysler vehicles 2004-up INTERFACE COMPONENTS CHTO-013 Interface 16-pin harness with stripped leads 10-pin harness to 22-pin Chrysler harness with
Más detallesNissan Altima (Sedan) 2013-up 95-7617GHG
INSTALLATION INSTRUCTIONS FOR PART 95-7617GHG KIT FEATURES Double DIN radio provision Painted Grey High Gloss APPLICATIONS Nissan Altima (Sedan) 2013-up 95-7617GHG Table of Contents Dash Disassembly Nissan
Más detallesHyundai Santa Fe 2007-2012
INSTALLATION INSTRUCTIONS FOR PART 95-7325 KIT FEATURES Double DIN radio provision Stacked ISO radio provision APPLICATIONS Hyundai Santa Fe 2007-2012 (not for factory equipped NAV models) 95-7325 Table
Más detallesCHTO-03 Chrysler Amplified Data Interface 2007-up
M4 M3 M5 ISO 6 2.5 1.5 INSTALLATION INSTRUCTIONS FOR PART CHTO-03 CHTO-03 Chrysler Amplified Data Interface 2007-up APPLICATIONS See inside front cover KIT FEATURES Provides accessory (12-volt 10-amp)
Más detallesHyundai Sonata GLS/SE (without NAV) 2011, Sonata (without NAV) 2012-up 99-7342
REV. 1/27/2014 INST99-7342 INSTALLATION INSTRUCTIONS FOR PART 99-7342 KIT FEATURES ISO DIN radio provision with pocket Double DIN radio provision Painted black and silver to match factory dash APPLICATIONS
Más detallesMercedes GLK 2010-up B
INSTALLATION INSTRUCTIONS FOR PART 99-8716B APPLICATIONS Mercedes GLK 2010-up 99-8716B KIT FEATURES DIN head unit provisions ISO DIN head unit provision Painted Matte Black to match factory finish KIT
Más detallesCadillac Amplified OnStar Interface
METRA. The World s best kits. 1-800-221-0932 metraonline.com COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION INSTALLATION INSTRUCTIONS FOR PART GMOS-06 GMOS-06 Cadillac Amplified OnStar Interface 1996-2005
Más detallesMitsubishi Endeavor 2004-up 99-7009
INSTALLATION INSTRUCTIONS FOR PART 99-7009 APPLICATIONS Mitsubishi Endeavor 2004-up 99-7009 KIT FEATURES DIN head unit provisions SO DIN head unit provisions KIT COMPONENTS A) Radio housing B) ISO brackets
Más detallesRam Trucks 2013-up (without 8.4 inch touchscreen) Modifications to factory radio cavity required for this installation 95-6518B
INSTALLATION INSTRUCTIONS FOR PART 95-6518B KIT FEATURES Double DIN radio provision Painted matte black APPLICATIONS Ram Trucks 2013-up (without 8.4 inch touchscreen) Modifications to factory radio cavity
Más detallesHyundai Sonata 2015-up DP-7363B
Installation instructions for part DP-7363B KIT FEATURES ISO DIN radio provision with pocket ISO Double DIN radio provision Painted matte black Hyundai Sonata 2015-up DP-7363B Table of Contents Dash Disassembly.
Más detallesCadillac STS amplified OnStar interface 2005-2011
INSTALLATION INSTRUCTIONS FOR PART GMOS-13 GMOS-13 Cadillac STS amplified OnStar interface 2005-2011 INTERFACE COMPONENTS GMOS-13 interface 16-pin Axxess harness with stripped leads 18-pin Axxess harness
Más detallesDouble DIN radio provision... 3 Double DIN radio provision Painted scratch resistant black
INSTALLATION INSTRUCTIONS FOR PART 95-8720B APPLICATIONS Smart ForTwo 2011-up Table of Contents 95-8720B Dash Disassembly Smart ForTwo 2011-up... 2 Kit Assembly KIT FEATURES Double DIN radio provision...
Más detallesGMOS-MOST-01 GM 2014-up MOST Amplifier Interface
Installation instructions for GMOS-MOST-01 REV. 9/4/2015 INSTGMOS-MOST-01 GMOS-MOST-01 GM 2014-up MOST Amplifier Interface FEATURES Provides accessory power (12-volt 10-amp) Retains R.A.P. (retained accessory
Más detallesNissan Altima (Sedan) 2013-up 99-7617GHG
INSTALLATION INSTRUCTIONS FOR PART 99-7617GHG KIT FEATURES ISO DIN radio provision with pocket Painted Grey High Gloss APPLICATIONS Nissan Altima (Sedan) 2013-up 99-7617GHG Table of Contents Dash Disassembly
Más detallesDodge Durango 2011-2013 Jeep Grand Cherokee 2011-2013 99-6513B
INSTALLATION INSTRUCTIONS FOR PART 99-6513B Dodge Durango 2011-2013 Jeep Grand Cherokee 2011-2013 99-6513B KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket Painted matte
Más detallesChrysler vehicles 2004-up
INSTALLATION INSTRUCTIONS FOR PART AX-ADCH100 AX-ADCH100 Chrysler vehicles 2004-up APPLICATIONS See inside front cover INTERFACE COMPONENTS AX-ADBOX1 Interface 16-pin harness with stripped leads 16-pin
Más detallesInstallation instructions for part 99-7367
Installation instructions for part 99-7367 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Factory clock and push to start provision 99-7367B - Painted matte black 99-7367HG -
Más detallesRam Trucks 2013-up (without 8.4 inch touchscreen) Modifications to factory radio cavity required for this installation 99-6518B
INSTALLATION INSTRUCTIONS FOR PART 99-6518B KIT FEATURES ISO DIN radio provisions with pocket Painted matte black APPLICATIONS Ram Trucks 2013-up (without 8.4 inch touchscreen) Modifications to factory
Más detalles2011 Honda CR-Z 95-7879
INSTALLATION INSTRUCTIONS FOR PART 95-7879 APPLICATIONS 2011 Honda CR-Z 95-7879 KIT FEATURES Double DIN mount radio provision Painted and textured to match factory finish KIT COMPONENTS A) Radio trim panel
Más detallesHyundai Azera 2006-2011 95-7322
INSTALLATION INSTRUCTIONS FOR PART 95-7322 APPLICATIONS Hyundai Azera 2006-2011 95-7322 KIT FEATURES Double DIN radio provision Stacked ISO unit provision KIT COMPONENTS A) Double DIN trim plate B) Double
Más detallesChrysler 300 2005-2007 99-6516B
INSTALLATION INSTRUCTIONS FOR PART 99-6516B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte black APPLICATIONS Chrysler 300 2005-2007
Más detallesGMOS-044 Chevrolet Cruze 2011-2015 / Cruze Limited 2016 (with monochrome screen)
Installation instructions for part GMOS-044 REV. 3/22/2016 INSTGMOS-044 GMOS-044 Chevrolet Cruze 2011-2015 / Cruze Limited 2016 (with monochrome screen) FEATURES Provides accessory power (12-volt 10-amp)
Más detallesHyundai Azera 2006-2011 99-7322
INSTALLATION INSTRUCTIONS FOR PART 99-7322 APPLICATIONS Hyundai Azera 2006-2011 99-7322 KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket KIT COMPONENTS A) Radio housing B) ISO
Más detallesChevy Cruze (with single color, monochrome screen) 2011-up 99-3011S
Installation instructions for part 99-3011S KIT FEATURES ISO DIN radio provision with pocket Double DIN radio provision Painted Silver to match factory finish APPLICATIONS Chevy Cruze (with single color,
Más detallesChrysler 300 2005-2007 99-6516B
INSTALLATION INSTRUCTIONS FOR PART 99-6516B KIT FEATURES DDIN radio provisions ISO DIN radio provisions with pocket Painted matte black APPLICATIONS Chrysler 300 2005-2007 99-6516B Table of Contents Dash
Más detallesNissan Pathfinder 2013-up (Without NAV and with the factory climate controls above the radio controls) 99-7626HG
Installation instructions for part 99-7626HG REV. 10/9/2015 INST99-7626HG KIT FEATURES ISO DIN radio provision with pocket DDIN radio provision Built and painted in multiple colors to match the factory
Más detallesNissan Altima 2007-up
INSTALLATION INSTRUCTIONS FOR PART 99-7423 APPLICATIONS Nissan Altima 2007-up 99-7423 KIT FEATURES DIN radio provision with pocket ISO mount radio provision with pocket Double DIN radio provision Stacked
Más detallesKia Optima 2011-2013. 99-7345B Dash Disassembly...2-3. Table of Contents
Installation instructions for part 99-7345B KIT FEATURES ISO DIN radio provision with pocket Painted matte black match factory dash KIT COMPONENTS A) Radio Brackets B) Radio trim panel C) Pocket D) (3)
Más detallesVolvo S60/V70 2001-2004 99-9223
INSTALLATION INSTRUCTIONS FOR PART 99-9223 APPLICATIONS Volvo S60/V70 2001-2004 99-9223 KIT FEATURES DIN head unit provision with pocket KIT COMPONENTS A) Radio housing A WIRING & ANTENNA CONNECTIONS (sold
Más detallesCadillac Amplified OnStar Interface 2003-2006
INSTALLATION INSTRUCTIONS FOR PART GMOS-10 GMOS-10 Cadillac Amplified OnStar Interface 2003-2006 INTERFACE COMPONENTS GMOS-10 interface 16-pin harness with stripped leads 14-pin harness to 16 and 20-pin
Más detalles95-7882B Dash Disassembly
Installation instructions for part 95-7882B KIT FEATURES ISO DDIN radio provision Honda Civic 2013-2015 95-7882B Table of Contents Dash Disassembly...2 Kit Preparation...3 Kit Assembly. ISO DDIN radio
Más detallesDodge Charger/Magnum 2005-2007 (without factory NAV) 99-6519B, 99-6519S, 99-6519CF
REV. 12/18/2013 INST99-6519 INSTALLATION INSTRUCTIONS FOR PART 99-6519 APPLICATIONS Dodge Charger/Magnum 2005-2007 (without factory NAV) 99-6519B, 99-6519S, 99-6519CF KIT FEATURES DIN radio provision with
Más detallesChevrolet Blazer 1995-1998, S10 1994-1998 GMC Jimmy 1995-1998, Sonoma 1994-1998 82-3043
Installation instructions for 82-3043 Chevrolet Blazer 1995-1998, S10 1994-1998 GMC Jimmy 1995-1998, Sonoma 1994-1998 82-3043 Table of Contents Door Disassembly... 2 Kit Assembly... 3 KIT FEATURES Adapts
Más detallesFord multi-kit 1995-2011 95-5817
Installation instructions for part 95-5817 KIT FEATURES ISO DDIN radio provision Note: Sub-dash modifications are necessary to use this dash kit. You will need to trim the sub-dash to gain suitable depth
Más detallesMitsubishi Outlander Sport 2011-2014 99-7014
REV. 12/15/2013 INST99-7014 Installation instructions for 99-7014 APPLICATIONS See application list inside Mitsubishi Outlander Sport 2011-2014 99-7014 KIT FEATURES ISO DIN radio provision with pocket
Más detallesUniversal aftermarket speaker installation kit
INSTALLATION INSTRUCTIONS FOR PART 82-4600 APPLICATIONS Universal aftermarket speaker installation kit 82-4600 KIT FEATURES Provides spacing for 6-1/2 aftermarket speaker installation. KIT COMPONENTS A)
Más detallesFord RSE/SYNC/THX retention interface 2007-up
INSTALLATION INSTRUCTIONS FOR PART AX-ADFD100 REV. 5/27/2015 INSTAX-ADFD100 AX-ADFD100 Ford RSE/SYNC/THX retention interface 2007-up FEATURES Provides accessory (12-volt 10-amp) Retains R.A.P. (retained
Más detallesFord SYNC retention interface 2008-up
INSTALLATION INSTRUCTIONS FOR PART AFSI-01 AFSI-01 Ford SYNC retention interface 2008-up INTERFACE COMPONENTS AFSI-01 Interface AXXESS 16-pin harness with stripped leads AXXESS 22-pin to Ford 24-pin and
Más detallesNissan Armada 2008-up Nissan Pathfinder LE, SE and SV 2008-2012 99-7620B
REV. 12/1/2014 INST99-7620B INSTALLATION INSTRUCTIONS FOR PART 99-7620B APPLICATIONS KIT FEATURES DDIN radio provision ISO DIN radio provision with pocket Painted scratch-resistant matte black Axxess interface
Más detallesGMOS-09 GM amplified OnStar Class II Data Bus Interface 2000-2004
M4 M3 M5 ISO 6 2.5 1.5 INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-09 GMOS-09 GM amplified OnStar Class II Data Bus Interface 2000-2004 APPLICATIONS See inside front cover KIT FEATURES Provides accessory
Más detallesChrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 95-6518B
Installation instructions for part 95-6518b KIT FEATURES Double DIN radio provision Painted matte black Note: Modifications to factory radio cavity is required for this installation KIT COMPONENTS A) Radio
Más detallesJeep Cherokee Latitude/Limited 2014-up 99-6526
Installation instructions for part 99-6526 Jeep Cherokee Latitude/Limited 2014-up 99-6526 KIT FEATURES ISO DDIN radio provision Painted scratch-resistant matte black with either silver (99-6526S) or bronze
Más detallesHyundai Sonata GLS/SE (without NAV) 2011, Sonata (without NAV) 2012-2014 99-7342
REV. 9/29/2014 INST99-7342 Installation Instructions for 99-7342 APPLICATIONS Hyundai Sonata GLS/SE (without NAV) 2011, Sonata (without NAV) 2012-2014 99-7342 KIT FEATURES ISO DIN radio provision with
Más detallesAX-ADFD01 Ford RSE/SYNC/THX retention interface 2007-up
Installation instructions for AX-ADFD01 AX-ADFD01 Ford RSE/SYNC/THX retention interface 2007-up INTERFACE COMPONENTS AX-ADFD01 harness REV. 4/13/2015 INSTAX-ADFD01 The AX-ADFD01 is designed to and MUST
Más detallesGMOS-LAN-04 GM LAN 11 amplified OnStar Interface 2006-up
M4 M3 M5 ISO 6 2.5 1.5 INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-LAN-04 GMOS-LAN-04 GM LAN 11 amplified OnStar Interface 2006-up APPLICATIONS See inside front cover KIT FEATURES Provides accessory (12-volt
Más detallesChrysler PT Cruiser 2006-2010 Dodge Durango 2004-2007 Jeep Grand Cherokee 2005-2007 95-6533B
Installation instructions for part 95-6533B Chrysler PT Cruiser 2006-2010 Dodge Durango 2004-2007 Jeep Grand Cherokee 2005-2007 95-6533B Table of Contents Dash Disassembly... 2 Kit Assembly... 3 KIT FEATURES
Más detalles2011 Hyundai Sonata 99-7342
KIT FEATURES INSTALLATION INSTRUCTIONS FOR PART 99-7342 APPLICATIONS 2011 Hyundai Sonata (For models equipped without Nav and with manual climate controls) 99-7342 ISO DIN head unit provision with pocket
Más detallesChrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B
Installation instructions for 99-6518B Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B KIT FEATURES ISO DIN radio provision
Más detallesGMOS-LAN-02 GM LAN 29 Amplified OnStar Interface 2006-up
M4 M3 M5 ISO 6 2.5 1.5 INSTALLATION INSTRUCTIONS FOR PART INSTGMOS-LAN-02 GMOS-LAN-02 GM LAN 29 Amplified OnStar Interface 2006-up APPLICATIONS See inside front cover KIT FEATURES Provides accessory (12-volt
Más detallesDodge Journey 2011-up (Models with 4.3 screen) 99-6520B
INSTALLATION INSTRUCTIONS FOR PART 99-6520B KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Included interface retains factory 4.3 screen Painted matte black to match factory
Más detalles