MINIDIM 1. User Manual / Instrucciones de Usuario. Rev

Tamaño: px

Comenzar la demostración a partir de la página:

Download "MINIDIM 1. User Manual / Instrucciones de Usuario. Rev"

Celia Naranjo Torres
hace 6 años
Vistas:

1 MINIDIM User Manual / Instrucciones de Usuario Rev..0.0

2 DESCRIPTIONS Read this manual carefully before using our MINIDIM. As a signal channel dimmer, the MINIDIM is a combination of a control interface and tension provider for our LEDLINE 00 WHITE modules as a LED fixture for application. A maximum of up to A loads are allowed on a single output, DMX address enables to be addressed by flipping the dip-switch.the dimmer is available in DMX Control Mode, Manual Dim Mode and features 0-0V analog input. The intensity of LED product can be dimmed in the Manual Dim Mode. DELIVERY PACKET Check for transport damage. You should be in possession of the following items: x MINIDIM Manual Should you discover transport damage after unpacking the equipment, inform the hauler immediately. Never connect a damaged device. You may also contact your supplier. TECHNICAL SPECIFICATIONS Power Requirement ~ V DC Output (AMax.) Input Control Protocol -pin terminal connector for DMX out -pin terminal connector for LOAD (Double output) -pin terminal connector for Power In -pin terminal connector for Analog In -pin terminal connector for DMX In DMX- (0) Operation temperature Dimensions Weights -0ºC to +0ºC 0(L)x0(W)x0(H)mm 00g *Please Note: Improvements and specifications in the design of the unit and the manual are subject to change without any prior written notice. OPERATION GUIDE.DMX Control Mode(DMX Addressing) In this mode, the dip-switch 0 is flipped to the" ON"position, & IN OFF. DMX address can be addressed using dip to and the intensity of LED production is dimmable. DMX is short for Digital Multiplex.This is a universal binary language used as a form of communication between intelligent fixtures. Each DipSwitch represents a binary value. MINIDIM User Manual/Manual de uso Page

3 0 Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals for example: START CH# Setting DMX address for. Flip switches,,& to the "ON"position = Dip switches# = = 0 SWITCHESON,,,,,,, START CH# = 0= ON OFF SWITCHESON,,,,,,,,,,,,,,,,,, Setting DMX address for 0. Flip switches,,,& to the "ON"position = Dip switches# = = =0 A DMX value (address) is set by combining the different dip switches that will add up to the value you wish to achieve,. Manual Dimming Mode In this mode, the dip-switch is flipped to the "ON" position, Flip the dip-switch ~ to set the intensity of LED product. Each Dip Switch represents a binary value. Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Dip Switch address equals Intensity 0 0 SWITCHES ON,,,,,,, Intensity = ON SWITCHES ON,,,,,,,,,,,,,,,,, 0 = ON The intensity is set by combining the different dipswitches that will add up to the value you wish to achieve, for example: Setting the Intensity for. Flip switches,,& to the Setting the Intensity for 0. Flip switches,,,& to the "ON" position "ON" position = = Dipswitches# = = Dipswitches# = =. Analog Input Mode =0 Flipping the dip-switch to "OFF" position, and the dip-switch 0 & are flipped to the "ON" position, the analog input is 0-0V and the intensity of LED product can be set in 0~00%. 0 = ON MINIDIM User Manual/Manual de uso Page

4 DESCRIPCION Lea cuidadosamente este manual antes de utilizar MINIDIM. Como dimmer monocanal, MINIDIM es la combinación de un interfaz de control y alimentador para nuestras tiras LED LINE 00 WHITE Una carga máxima de A es el valor máximo permitido en la salida. El direccionamiento DMX permite direccionar la unidad mediante dipswitches. El dimmer dispone de control DMX o Manual, suministrando entrada analógica de 0-0 V. La insidad de la carga puede ser dimmerizada en modo Manual. CONTENIDO Compruebe si la unidad ha sufrido daños durante el transporte. La unidad debe contener: MINIDIM Manual Si detecta daños durante el transporte despues de desembalar la unidad, informe a su distribuidor de inmediato. Nunca conecte un dispositivo dañado. ESPECIFICACIONES TECNICAS Requerimientos de Potencia ~VDC Salida (A Max.) Terminales -pin para DMX out Terminales -pin para LOAD (Salida doble) Entrada Protocolo de control Terminales -pin para alimentación Terminales -pin para Analog In Terminales-pin para DMX In DMX-(0) Temp. de uso Dimensiones Peso -0ºC +0ºC 0(L)x0(An)x0(Al)mm 00g *Nota: Cambios en las especificaciones y diseño de la unidad o de este manual, están sujetos a cambios sin previo aviso. GUIA DE USO.Modo de control DMX ( Direc. DMX) = ON En este modo el dipswitch 0 está en la posición ON, la 0 dirección DMX puede ser configurada y la intensidad es dimmerizable. DMX es la abreviatura de Digital Multiplkex. Es un lenguaje universal binario usado para la comunicación entre unidades inteligentes. Cada dipswitch representa un valor binario. MINIDIM User Manual/Manual de uso Pagina

5 0 0 Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switchaddress equivale a Dip Switch address equivale a Dip Switch address equivale a CANAL SWITCHES ON CANAL SWITCHES ON,,,,,, 0, = ON,,,,,,,,,,,,,,,,,, Un valor DMX (Dirección) se configura como la combinación de diferentes dipswitches que conforman un valor obtenido. por ejemplo: Configurar la dirección DMX a Configurar la dirección DMX a 0 Pasar los switch, y a Pasar los switches,, y a = = Dipswitches# = Valor Dipswitches# = Valor = = =0. Modo dimmerización manual En este modo el dipswitch se configura en la posición ON, Los dipswitch - configuran la intensidad de los LED. Cada dipswitch representas un valor binario. Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Dip Switch address equivale a Valor Intensidad 0 Switch on,,,,,,, = ON Valor Switch on Intensidad,,,,,,,,,,,,,,,,, Un valor de intensidad se configura como la combinación de diferentes dipswitches que conforman un valor obtenido. por ejemplo: Configurar la intensidad a Configurar la intensidad a 0 Pasar los switch, y a Pasar los switches,, y a = = Dipswitches# = Valor Dipswitches# = Valor = = =0. Modo entrada analógica En este modo el dip-switch pasa a "OFF" y losdip 0 y a la posición "ON", la entrada analógica es de 0-0V y la intensidad del LED puede ser configurada de 0 a 00% 0 = ON MINIDIM User Manual/Manual de uso Pagina

6 EQUIPSON, S.A. Avda. El Saler, - Pol. Ind. L Alteró,0 - Silla (Valencia) Spain Tel. + 0 Fax support@work.es

Documentos relacionados

ENKVM-USBB. 2-Port USB KVM switch with Easy Switch and Cable. User Guide

ENKVM-USBB. 2-Port USB KVM switch with Easy Switch and Cable. User Guide ENKVM-USBB 2-Port USB KVM switch with Easy Switch and Cable User Guide i Package Contents 1 ENKVM-USBB 2-Port USB KVM Switch with Easy Switch and Cable 1 User Guide Requirements Console A VGA, SVGA, XGA,