INSTRUCCIONES DE ENSAMBLAJE.

Transcripción

1 English MULTI-FUNTIONAL OMPUTER TABLE ASSEMBLY INSTRUTION MODEL RTA - Q207 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents over surfaces or structural tubes. Thanks for purchasing one of our products, please read carefully the assembly instructions before the installation (Attention: Do not tighten the screws before all screws are in place). MODEL RTA-Q207 B

2 Spanish INSTRUIONES DE ENSAMBLAJE. MODELO RTA-Q207 IMPORTANTE: Para su limpieza sobre la superficies utilice una toalla humedecida en una solución de agua y jabón de pasta y luego pase sobre esta un trapo seco. No utilice solventes, sobre las superficie ni las estructuras tubulares. Gracias por comprar uno de nuestros productos por favor lea cuidadosamente las instrucciones de ensamblaje antes de instalar la unidad.(atencion: No adjuste firmemente los tornillos antes de tener la estructura completamente armada). MODELO RTA-Q207

3 RTA-Q207 P Main Panels Bottom Tubes Studs Bottom Panel Paneles Principales Tubos Inferiores Topes Panel Inferior Drawer Box Side Panel Printer Panel Tabletop Back Tubes Panel Lateral de Gaveta Panel de Impresora Panel Superior Tubos Posteriores Back panel Long Tube Slider bases Sliders Panel Posterior Tubo Largo Bases para Deslizadores Deslizadores Keyboard Panel Rack Side panels Horizontal Tubes Rack Bottom panel Panel de Teclado Paredes Laterales de Tubos Horizontales Panel Inferior de Anaquel de Anaquel Anaquel

4 RTA-Q207 P A 2 Handle Side Panels Screw over Manija Paneles Laterales Tapa para Tornillos 22 B Decorative ap Tapones Decorativos Washer Arandelas Nut Tuercas Drawer Panel Panel de Gaveta 25 Drawer Panel Drawer Front Panel Drawer Bottom Panel Panel de Gaveta Panel Frontal de Gaveta Panel Inferior de Gaveta Drawer Back Panel Panel Posterior de Gaveta Drawer Sliders Deslizadores de Gaveta Drawer Box Back Panel Panel Posterior de la aja de la Gaveta PART QTY. ITEM PART QTY. ITEM A 8 3X5 MM G 4 6X2 MM B 2 6X50 MM H 4 4X4 MM MM I 4 4X30 MM D 0 6X30 MM J 4X20 MM E 2 60 MM F 4 4 MM

5 RTA-Q207 P.5 60MM BOLT INSTALLATION AS BELOW: 6x40mm INSTALE EL PERNO ASI: Bolt Perno onnecting piece Pieza de ajuste Adjust connecting piece direction if condition as illustrated uando la pieza de ajuste este desviada, debe alinearla antes de insertar el perno Insert bolt when onnecting piece under Such condition Inserte el Perno cuando la Pieza de ajuste este alineada A. A2. A B 6X50 MM Insert the Studs (3) into the Bottom Tubes (2) and tighten them well. Inserte los Topes (3) en los Tubos Inferiores (2) y ajústelos bién. Use Screws B to assemble the Bottom Tubes (2) to the Main Panels (). Use Tornillos B para ensamblar los Tubos Inferiores (2) a los Paneles Principales ().

6 RTA-Q207 P MM Insert the Bolts () into the holes of the Bottom Panel (4) and tight them with the screwdriver, then place the Drawer Box Back & Side Panels (5 & 27) over the Bolts and tight the nuts on the inside face of the Drawer Box Back & Side Panels (5 & 27). Inserte Pernos en los agujeros del Panel Inferior (4) y ajústelos con el destornillador,luego coloque el Panel Lateral de Gaveta (5) y el Panel Posterior degaveta (27) sobre los Pernos y ajuste las tuercas colocadas en la parte interna de los Paneles (5 y 27). 4 A 3X5 MM Use Screws A to assemble the Drawer Sliders (25) to the left Main Panel () & to the Drawer side Panel (5). Use Tornillos A para ensamblar el Deslizador de Gaveta (25) al Panel Principal izquierdo () y el Deslizador de Gaveta derecho al Panel Lateral de Gaveta (5).

7 RTA-Q207 P MM Use Bolts to assemble the Printer Panel (6) to the Drawer's Back and side Panels (5 and 27). Use Pernos para ensamblar el Panel de Impresora (6) a los Paneles Lateral y Posterior de la aja de la Gaveta (5 y 27) MM X6 Use Bolts to assemble the Tabletop (7) & the Printer Panel (6) & the Bottom Panel (4) to the left Main Panel (). Use Pernos para ensamblar el Panel Superior (7), el Panel de Impresora (6) y el Panel Inferior (4) al Panel Principal izquierdo ().

8 RTA-Q207 P MM 7 D 6X30 MM X6 Use Screws to assemble the Main Panel () to the Tabletop (7) & the Bottom Panel (4). Use Pernos para ensamblar el Panel Principal derecho () al Panel Superior (7), y al Panel Inferior (4). Use Screws D to assemble the Back Tubes (8) to the Main Panels (). Use Tornillos D para ensamblar los Tubos Posteriores (8) a los Paneles Principales (). 9 E 60 MM X B 6X50 MM Use Screws B to assemble the BackPanel (9) between the Back Tubes (8). Use Screws E to assemble the Long Tube (0) between the Main Panels (). Then place the Screw over (9) over the Main Panels () Use Tornillos B para ensamblar el Panel Posterior (9) entre los Tubos Posteriores (8).Use Tornillos E para ensamblar el Tubo Largo (0) entre los Paneles Principales ().Luego coloque las Tapas para Tornillos (9) en los Paneles Principales ().

9 RTA-Q207 P X MM X2 4 6 Insert the Bolts into the holes of the Rack Side panels (4) and tight them with the tool, then assemble The Rack Bottom panel (6) with this bolts. Tight the nuts on the back face of the Rack Bottom panel (6). Insert the Horizontal Tubes (5) between the Rack Side panels (4). Inserte Pernos en los agujeros de los Paneles Laterales de Anaquel (4) y ajustelos con el destornillador, luego ensamble entre los laterales, el Panel Inferior de Anaquel (6) con éstos Pernos y ajustelos por la cara posterior. Inserte los Tubos Horizontales de Anaquel (5) entre los Paneles Laterales de Anaquel (4). 4 4 B 6X50 MM Use Screws B to assemble the Rack Side panels (4) to the left Main Panel (). Use Tornillos B para ensamblar los Paneles Laterales de Anaquel (4)con el Panel Principal izquierdo () F 4 MM Use Screws F to fix the Slider Bases () to the Sliders (2). Use Tornillos F para fijar las Bases de los Deslizadores () a los Deslizadores (2).

10 RTA-Q207 P G 6X2 MM 2 Use Screws G to assemble the Slider Bases () with the Tabletop (7). Use Tornillos G para ensamblar las Bases de los Deslizadores () con el Panel Superior (7) H 4X4 MM Use Screws H to fix the Keyboard Panel (3) to the Sliders (2). Use Tornillos H para fijar el Panel de Teclado (3) a los Deslizadores (2).

11 RTA-Q207 P. 5 20A X0 H 4X4 MM X0 20B X0 20 X0 8 8 Use screws H to fix the Nuts (20) and the Washers (20B) to the Side Panels (8). Then place the Decorative aps (20A) and tighten them well. Use Tornillos H para fijar Tuercas (20 ) y Arandelas (20 B) a los Paneles Laterales (8).Luego coloque los Tapones Decorativos (20 A) y ajuste bién. 6 8 D 6X30 MM 8 Use Screws D to assemble the Side Panels (8) with the Main Panels (). Use Tornillos D para ensamblar los Paneles Laterales (8) con los Paneles Principales ().

12 RTA-Q207 P MM 2 Use Bolts fix the Drawer Panel (2) & the Drawer Panel (22) to the Drawer Front Panel (23). 23 Use Pernos para fijar el Panel de Gaveta (2) y el Panel de Gaveta (22) al Panel Frontal de Gaveta (23) I 4X30 MM 23 Insert the Drawer Bottom Panel (24) between the Drawer Panel (2) & the Drawer Panel (22). Inserte el Panel Inferior de Gaveta (24) entre los Paneles de Gaveta (2) y (22). Use Screws I to assemble the Drawer Back Panel (25) between the Drawer Panel (2) & the Drawer Panel (22). Use Tornillos I para ensamblar el Panel Posterior de Gaveta (25) entre los Paneles (2) y de Gaveta (22) A 3X5 MM 23 Align selected holes on slides as illustrated with predrilled holes on drawer box before inserting screws Haga coincidir los agujeros seleccionados en los Deslizadores con los agujeros pre-taladrados sobre el cajón de la gaveta(como indica la ilustración) antes de insertar los tornillos. Use Screws A to assemble the Drawer Sliders (26) to the Drawer left & Panels (2 & 22). Use Tornillos A para ensamblar los Deslizadores de Gaveta (26) a los Paneles (2) y de Gaveta (22).

13 RTA-Q207 P.3 2 J 4X20 MM X 23 7 Use Screws J to fix the Handle (7) to the Drawer Front Panel (23). Use Tornillo J para fijar la Manija (7) al Panel Frontal de Gaveta (23) Put the Drawer in it's place. oloque la Gaveta en su lugar. Tighten all screws well and enjoy your unit. Ajuste bién todos los Tornillos y disfrute de su unidad.

14

15 PRODUT WARRANTY TEHNI MOBILI DESK WARRANTY LIMITED 5-YEAR WARRANTY RTA Products, LL warrants to the Original Purchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. "Defects" as used in this warranty, is defined as any imperfections that impair the use of the furniture or product. RTA products will repair or replace, at is option, without charge to the original purchaser other than freight from purchaser to RTA Products, only the defective products or parts for a period of FIVE (5) Years. Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or merchantability or of fitness for a particular purpose. Please note, all desks made with PV Laminate surface should not be exposed to direct sunlight, as it may damage the material. Damage of this nature is not covered under this warranty. RTA Products will not be responsible for indirect, special, incidental or consequential damages. This warranty is limited to merchandise purchased in the ontinental United States. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state. RTA Products will advise you of the procedure to follow in making warranty claims. The following are the procedures for warranty claims: a. all us Monday Friday, from 9am-5pm (Eastern Time) at (866) to explain the defect and give your name, address and phone number. Please have ready the model number of our product, date and place of purchase. You can also write to us by to warranty@rtaproducts.com and include the same information. b. If we determine that replacement will remedy the situation, and in order to determine the extent or the cause of the defect, purchaser will need to send the part in question at purchaser s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.