INSTALLATION INSTRUCTIONS FOR PART 99-7348B APPLICATIONS Hyundai Accent with radio delete 2012-up 99-7348B KIT FEATURES ISO DIN head unit provision with pocket DDIN head unit provisions Painted Black to match factory finish KIT COMPONENTS A) Radio trim panel B) DDIN Brackets C) Pocket D) (4) #8 x 3/8 Truss head Phillips screws A B C D WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: 70-7304 - Kia/Hyundai harness 2010-up Antenna Adapter: Not required TOOLS REQUIRED Panel removal tool Phillips screwdriver Socket wrench REV. 2/23/12 METRA. THE WORLD S BEST KITS. 1-800-221-0932 metraonline.com COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
99-7348B Table of Contents Dash Disassembly Hyundai Accent with radio delete 2012-up 3 Kit Assembly ISO DIN head unit provision with pocket 4 DDIN head unit provisions 5 Caution: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians
Dash Disassembly 99-7348B Hyundai Accent with radio delete 2012-up 1. Remove radio surround panel from dash. Disconnect harnesses. (Figure A) 2. Remove (4) Phillips screws securing radio block-off plate and remove it from the dash panel. (Figure B) Continue to kit preparation (Figure A) (Figure B) 3
Kit Assembly 99-7348B ISO DIN head unit provision with pocket 1. Attach the radio brackets to the radio trim panel. (Figure A) 2. Attach the pocket to the trim panel/ bracket assembly with the supplied (4) #8 Phillips truss head screws. (Figure B) 3. Attach the radio to the trim panel/bracket/pocket assembly with the screws supplied with the unit. (Figure C) 4. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from the Metra and/or AXXESS. 5. Reassemble dash in reverse order of disassembly. (Figure D) (Figure B) (Figure C) (Figure A) (Figure D) 4
Kit Assembly 99-7348B Double DIN head unit provisions 1. Attach the radio brackets to the radio trim panel. (Figure A) 2. Attach the DDIN radio to the trim panel/ bracket assembly with the screws supplied with the unit. (Figure B) 3. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from the Metra and/or AXXESS. 4. Reassemble dash in reverse order of disassembly. (Figure C) (Figure A) (Figure B) (Figure C) 5
Notes
Notes
INSTALLATION INSTRUCTIONS FOR PART 99-7348B REV. 2/23/12 METRA. THE WORLD S BEST KITS. 1-800-221-0932 metraonline.com COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7348B APLICACIONES Hyundai Accent 2012 y más recientes con radio borrar 99-7348B CARACTERÍSTICAS DEL KIT Provisión de unidad central ISO DIN con bolsillo Provisiones de unidad central DDIN Pintada en negro para igualar el acabado de fábrica COMPONENTES DEL KIT A) Panel de moldura para radio B) Soportes DDIN C) Bolsillo D) (4) tornillos Phillips #8 de 3/8 A B C D CABLEADO Y CONEXIONES DE ANTENA (se venden por separado) Arnés de cableado: Arnés 70-7304 para Kia/Hyundai 2010 y más recientes Adaptador de antena: No se requiere HERRAMIENTAS REQUERIDAS Herramienta de remoción de panel Destornillador Phillips Llave de tubo REV. 2/23/12 METRA. THE WORLD S BEST KITS. 1-800-221-0932 metraonline.com COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
99-7348B Indice Desmontaje del tablero Hyundai Accent 2012 y más recientes con radio borrar... 3 Ensamble del kit Provisiones de unidad central ISO DIN con bolsillo... 4 Provisiones de unidad central doble DIN... 5 PRECAUCIÓN: Metra recomienda desconectar el terminal negativo de la batería antes de comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces indicadoras de airbag deben estar enchufados antes de volver a conectar la batería o comenzar el ciclo de ignición. Nota: Remítase a las instrucciones incluidas con el radio de posventa. EL CONOCIMIENTO ES PODER Mejore sus habilidades de instalación y fabricación inscribiéndose en la escuela de dispositivos electrónicos móviles más reconocida y respetada de nuestra industria. Regístrese en www.installerinstitute. com o llame al 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP).
Desmontaje del tablero 99-7348B Hyundai Accent 2012 y más recientes con radio borrar 1. Quite el panel que rodea el radio del tablero. Desconecte los arneses. (Figura A) 2. Quite los (4) tornillos Phillips que sostienen el chasís del radio en el sub tablero. Desconecte los arneses y las antenas. (Figura B) Continuará la preparación del kit (Figura A) (Figura B) 3
Ensamble del kit 99-7348B Provisiones de unidad central ISO DIN con bolsillo 1. Una los soportes del radio al panel de la moldura del radio. (Figura A) 2. Una el bolsillo al panel de la moldura/ ensamble de soporte con los (4) tornillos Phillips de cabeza segmentada #8 que se incluyen. (Figura B) 3. Una el radio al panel de la moldura/ soporte/ensamble de bolsillo con los tornillos que vienen con la unidad. (Figura C) 4. Ubique el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. 5. Vuelva a armar el tablero al revés de como lo desarmó. (Figura D) (Figura B) (Figura C) (Figura A) (Figura D) 4
Ensamble del kit 99-7348B Provisiones de unidad central doble DIN 1. Una los soportes del radio al panel de la moldura del radio. (Figura A) 2. Una el radio DDIN al panel de la moldura/soporte/ensamble con los tornillos que vienen con la unidad. (Figura B) 3. Ubique el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. 4. Vuelva a armar el tablero al revés de como lo desarmó. (Figura C) (Figura A) (Figura B) (Figura C) 5
Notes
Notes
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7348B REV. 2/23/12 METRA. THE WORLD S BEST KITS. 1-800-221-0932 metraonline.com COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION