CAMILEO H30 User s Guide

Transcripción

1 CAMILEO H30 User s Guide English/Español GMAA /10

2 2 Regulatory Information FCC Information Product Name: Camcorder Model number: CAMILEO H30 FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment.

3 FCC Conditions This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc Irvine Boulevard Irvine, California Telephone: (949) Safety Instructions 1 Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided. 2 Avoid all contact with water, and dry hands before using. 3 Do not expose the camcorder to high temperature or leave it in direct sunlight. Doing so may damage the camcorder. 4 Use the camcorder with care. Avoid pressing hard on the camcorder body. 5 For your own safety, avoid using the camcorder when there is a storm or lightning. 6 Do not use batteries of different specifications. Doing so may lead to the potential for serious damage. 7 Remove the battery during long periods between usage, as a deteriorated battery may affect the functionality of the camcorder. 8 Remove the battery if it shows signs of leaking or distortion. 9 Use only the accessories supplied by the manufacturer. 10 Keep the camcorder out of the reach of infants. 11 Risk of explosion if battery is replaced by an incorrect type. 12 Dispose of used batteries according to the instructions. 3

4 4 About the battery pack Use only batteries recommended by TOSHIBA as replacements. The battery pack is lithium ion batteries, which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. Safety icons Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Only use the supplied AC adaptor or USB cable, or an optional Toshiba battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger. This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, may result in property damage. NOTE Provides important information.

5 Additional Information Trademarks Copyright 2010 TOSHIBA CORPORATION. All rights reserved. TOSHIBA reserves the right to make technical changes. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between this product and the documentation. Adobe and Photoshop are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. ArcSoft, MediaImpression, and MediaConverter are registered trademarks of ArcSoft, Inc. HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Secure Digital and SD are trademarks of SD Card Association. YouTube and the YouTube logo are registered trademarks of Google, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies. 5

6 Contents Chapter 1: Getting to Know Your Camcorder...9 Overview...9 Check the Components...10 System Requirements...10 Front view...11 Rear view...11 Side views...12 Underside view...12 Chapter 2: Getting Started Loading the battery...13 Charge your battery...14 Inserting and removing an SD Card (optional)...18 Turning the camcorder on and getting started...19 Turning off the camcorder...19 Chapter 3: Record Mode Button functions...20 LCD touch screen information...21 Menu options...22 Movie recording

7 Contents 7 Using the pre-record function...24 Picture recording...25 Taking close up pictures/movies...25 Using the Flash or digital light function...26 Using zoom...26 Record menu options...27 Movie Record mode menu...27 Picture record mode menu...27 Record mode operations...27 Movie resolution...28 Picture resolution...29 White balance...29 Scene...30 Movie effects...31 Stabilization...31 Macro mode...32 Motion Detection...32 Slow Motion...33 Time Lapse...33 Picture effects...34 Self-Timer...34 Macro mode...35 ISO...35 Chapter 4: Playback Mode LCD touch screen information...37 Playback mode operations...39 Movie playback...40 Delete movies...41 Picture playback...42 Delete picture...43 Chapter 5: Camcorder Settings Settings Menu...44 Sound...45 TV...45

8 8 Contents Language...46 Time Settings...46 Format...47 Default settings...48 Chapter 6: Viewing Pictures and Movies on TV Connecting to a high-definition 16:9 (wide) TV...50 Connecting to a non-high-definition 4:3 TV...51 Chapter 7: Viewing Pictures and Movies on a Computer Installing bundled software...52 Transferring pictures or movies to a computer...53 Chapter 8: Burning Recorded Clips to DVD Chapter 9: Uploading Video Files to YouTube Chapter 10: Video File Converter Chapter 11: Specifications Operating Environment Conditions...68 Chapter 12: Troubleshooting Chapter 13: Other Information Toshiba Support...71 Before you call...71 Contacting Toshiba...72 Toshiba s technical support Web site...72 Toshiba voice contact...72 Warranty...72 Online Warranty Information...72 Warranty Service...72

9 Chapter 1 Getting to Know Your Camcorder Overview Your Toshiba camcorder comes equipped with a 5 Mega Pixel sensor that can record H.264 format movies. This format allows for extended video recording with less memory. Other features of your Camileo H30 camcorder are: High quality images up to 16 mega-pixels Color LCD touch screen for easy viewing of video and pictures Video recording at an HD resolution of 1920 x1080 HDTV connectivity via an HDMI cable Easy playback of recorded high-definition videos on wide screen HDTV Built-in YouTube Direct application, allowing you to upload videos captured by the camcorder to YouTube more effortlessly ISO and color balance can be set to automatic or manually adjusted 5x optical zoom, 4x (1x for 1080p) digital Various effect options, such as Time Lapse and Slow Motion Built-in memory allowing you to take pictures and to record movies without a memory card. 9

10 SET 10 Getting to Know Your Camcorder Overview NOTE Memory card slot allowing users to increase storage capacity. A portion of the built-in memory is used for Firmware to operate the camcorder. Check the Components Unpack the box and make sure all listed items below are included: Camcorder USB Cable AV Cable HDMI Cable AC-Adaptor Remote Control Lithium-ion n Rechargeable Battery Quick Start Guide CD-ROM (Software & User s Manual) Cloth Bag Cleaning Cloth Lens Cover Set (Lens cover & strap) *preinstalled in camcorder device (Sample Illustration) Components NOTE Be sure to remove the protective film on the lens before using. System Requirements Microsoft Windows XP/Windows Vista /Windows 7 Intel Pentium III 800 MHz or above 256 MB RAM 4x CD-ROM Drive 700 MB free HDD space Available USB 2.0 port NOTE The LCD touch screen is manufactured using extremely highprecision technology. However, some tiny black and/or bright dots (white, red, blue or green) may appear on the LCD touch screen. These dots are a normal result of the manufacturing process, and do not affect the recording.

11 Getting to Know Your Camcorder Overview 11 Front view Tele/Wide button Speaker Lens Flash Microphone Rear view Self-Timer LED (Sample Illustration) Front view Playback LED indicator Movie Mode LED indicator Picture Mode LED indicator Playback button Rolling wheel Mode button OK button (Sample Illustration) Rear view

12 12 Getting to Know Your Camcorder Overview Side views Power button Pre-Record/YouTube Direct button LCD touch screen Underside view TV port (Sample Illustration) Side views Mini USB 2.0 port HDMI port Tripod socket Battery/SD Card cover (Sample Illustration) Underside view

13 Chapter 2 Getting Started Loading the battery Before using the camcorder, you will need to remove the protective film from the battery. To do so, remove the battery, then remove the film, and replace the battery as shown below. (Sample Illustration) Reinserting the battery 13

14 14 Getting Started Loading the battery Charge your battery You must use the supplied AC adaptor or the USB cable to charge your camcorder before use. Turn off the camcorder. A blinking light will indicate active charging and a solid light will indicate that charging is complete. In AC charging mode, the light will turn off automatically after 5 minutes. (Sample Illustration) Charging the battery Handling of the battery pack Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven). Heat can cause a battery pack to explode and/or release caustic liquid, both which may possibly cause serious injury. Never attempt to disassemble, tamper with or repair a battery pack. The battery pack could overheat and ignite. Leakage of the caustic alkaline solution or other electrolytic substances could cause fire, possibly resulting in death or serious injury. Never short-circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or a fire, and could also damage the battery pack and product. Always wrap the battery pack in plastic (or place it in a plastic bag) whenever transporting it, to avoid exposing the terminals to another conductive object which could result in serious injury. Always cover the metal terminals with insulating tape when disposing of the battery pack, to prevent accidental shortcircuiting which could result in serious injury.

15 Getting Started Loading the battery 15 Never drive a nail or any other sharp object into the battery pack, hit battery pack with a hammer or other object or step on it. Doing so could cause a fire or explosion possibly resulting in serious injury. Never charge the battery pack by a method other than as instructed. Doing so could cause a fire or explosion possibly resulting in serious injury. Never connect the battery pack to a plug socket or a car cigarette plug socket. The battery pack could rupture or ignite causing a fire or explosion possibly resulting in serious injury. Never allow a battery pack to become wet. A wet battery pack will overheat or ignite causing rupture or fire, possibly resulting in death or serious injury. Never store a battery pack in an area of high humidity. This could cause a fire or explosion possibly resulting in serious injury. Never expose a battery pack to abnormal shock, vibration or pressure. Never use a battery pack which has been exposed to abnormal shock even if the appearance is normal. The battery pack s internal protective device could fail, causing it to overheat or ignite resulting in caustic liquid leakage, or explosion or fire, possibly resulting in death or serious injury. Never subject a battery pack to heat, and never store it or use it near a heat source. The battery pack could ignite or explode when heated or burned, possibly resulting in death or serious injury. Subjecting a battery pack to heat could also cause caustic liquid to leak. It can also cause failure, malfunction, or loss of stored data. Use of correct battery pack Always use the battery pack supplied. Other battery packs have different voltage and terminal polarities. Use of non-conforming battery packs could generate smoke or cause fire or rupture, possibly resulting in serious injury.

16 16 Getting Started Loading the battery Battery safety Never allow caustic electrolyte fluid leaked from the battery pack to contact your eyes, body or clothing. Use appropriate protective gloves when handling a damaged battery. If caustic electrolyte fluid from the battery pack should contact your eyes, immediately wash your eyes with large amounts of running water and obtain prompt medical attention, to help prevent permanent eye damage. If electrolyte fluid should contact any part of your body, immediately wash it off under running water to help prevent skin rashes. If electrolyte fluid should contact your clothes, promptly remove them to help prevent the electrolyte fluid from contacting your body, possibly resulting in serious injury. Battery pack warning indicators Always immediately turn the power off and disconnect the power cable/cord plug from the plug socket and stop using the battery pack if you observe any of the following conditions: Offensive or unusual odor Excessive heat Discoloration Deformation, cracks or leaks Smoke Other unusual event during use, such as abnormal sound In such an event, carefully and immediately remove the battery pack from the product. In some instances, you might have to wait for the product to cool down before removing the battery pack, in order to avoid any possible minor injury due to heat exposure. Do not turn on the product s power again until an authorized Toshiba service provider has checked it for safety. Continued use could cause a fire or rupture possibly resulting in serious injury or product failure including but not limited to the loss of data.

17 Getting Started Loading the battery 17 Disposal of used battery packs Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury. Inserting the battery pack When installing a battery pack or before moving the product, always make sure the battery pack is inserted correctly and securely. If the battery falls out, while you are carrying the product, you could be injured or the battery pack could be damaged. Do not use an impaired or exhausted battery pack Never continue to use a battery pack after its recharging capability has become impaired, or after the warning message indicating that the battery pack power is exhausted has been displayed. Continued use of an exhausted or impaired battery pack could result in the loss of data or damage to the product. NOTE Handling of the battery pack Never attempt to install batteries in reverse polarity. Make sure the battery is securely installed in the product before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture.

18 18 Getting Started Inserting and removing an SD Card (optional) The battery pack is lithium ion batteries, which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Inserting and removing an SD Card (optional) Your camcorder comes with internal memory that allows you to store pictures and movies. You can expand the memory capacity by using an optional SD /SDHC memory card. 1 Insert the memory card into the slot until it locks in place as shown below. 2 To remove an installed SD card, gently press the card inward to release it. The card pops out slightly. 3 Grasp the card and pull it straight out. (Sample Illustration) Inserting and removing an SD Card NOTE When a memory card is inserted, movies and pictures are saved onto the card rather than the built-in memory.

19 Getting Started Turning the camcorder on and getting started 19 Turning the camcorder on and getting started To turn on the camcorder, either: 1 Flip the LCD touch screen outward to turn on the camcorder automatically. 2 Or press the Power button for approximately one second to turn it on. To record movies: Press the Mode button or touch on the screen to switch to Movie Record mode. The Movie Mode LED Indicator ( ) lights up. Press the OK button to begin recording. To take a picture: Press the Mode button or touch on the screen to switch to Picture Record mode. The Picture Mode LED Indicator ( ) lights up. Press the OK button half-way down until the focusing frame turns from white to green. Continue to press the button down to take a picture. Focusing Frame: White Focusing Frame: Green To take a picture while recording a movie: When recording movies, press the Mode button ( ) to capture a still image. The Dual record icon ( ) displays on the LCD touch screen. To view stored movies and pictures: Press the Playback button or press on the screen to switch to Playback mode (The Playback LED indicator lights up). Press the Mode button or touch on the screen to switch between the Movie Preview Screen and the Picture Preview Screen. Turning off the camcorder To turn off the camcorder: You can either press the Power button for one second, or you can place the LCD touch screen back to its original position.

20 Chapter 3 Record Mode Button functions Rolling button: Rotate to move among menu options. Right button: LCD touch screen information ON/OFF. In the Record menu, press to switch to the submenu. Left button: Flash Auto/Red-Eye-Reduction/Digital Light/Flash OFF. In Record menu, press to return to the main menu. Up button: Move between option items. Down button: Move between option items. OK button: 1 Confirm settings. 2 In Movie Record mode, press to record movies, press again to stop recording, 3 In Picture Record mode, press to take pictures. Tele button: Zoom in Wide button: Zoom out Playback button: 1 Switch between Record and Playback modes. 2 Press after recording for a quick review. 3 In the Record menu, press to exit. 20

21 Record Mode LCD touch screen information 21 Mode button: 1 Switch between Movie mode and Picture mode. 2 When recording movies, press to capture a still image. Power button: Press down for one second to turn the camcorder on or off. Pre-Record/YouTube Direct button: In Record mode, press to activate the Pre-Record function and the movie will be recorded 3 seconds before the OK button is pressed. LCD touch screen information The indicators shown below may appear on the LCD touch screen when recording movies and/or taking pictures: (Sample Image) LCD touch screen icons

22 22 Record Mode LCD touch screen information Menu options Movie Resolution FHD (1080p/30fps) HD (720p/30fps) WVGA 60 (1) VGA (4:3) Slow motion (Record movies at 320 x 240 resolution) Picture resolution High (16 MP) Standard (10 MP) Low (3 MP) (2) (3) Remaining time of recording that can be made at the current resolution Number of images that can still be taken at the current resolution Self-timer enabled Dual Record (to take a still picture while recording a movie) (4) Stabilization (5) Pre-Record Mode Time Lapse Scene Skin (6) Night Backlight (7) Macro Position Focusing

23 Record Mode LCD touch screen information 23 (8) Manual White Balance (9) Motion Detection (10) Zoom meter: FHD (1080 p30):1x~5x (5X Optical zoom and 1X Digital zoom) Other video resolution:1x~20x (5X Optical zoom and 4X Digital zoom) (11) Record menu (12) Playback mode (13) Movie/Picture Record mode Movie mode Digital Light Picture mode (14) Flash Auto Red Eye Reduction Digital Light Flash Off (15) SD Card Inserted Battery: Full power Battery: Medium power (16) Battery: Low power Battery: No power DC power mode

24 24 Record Mode Movie recording NOTE Scene: B/W / Classic / Negative effect can be previewed immediately without indicator on the LCD touch screen. Movie recording In Movie Record mode (The Movie Record indicator light ( ) is lit), press the OK button to start recording. When a movie is being recorded, a time indicator will display on the LCD touch screen. To stop recording, press the OK button again. Dual Record is an optional function that allows you to take a still picture while recording a movie. To use Dual Record, press the Mode button ( ) to capture a still image. The Dual Record icon ( ) appears on the LCD touch screen. Press the Playback button to view a recorded movie. The four resolution settings available are: Video Quality FHD (1080p/30fps) HD (720p/30fps) WVGA 60 VGA (4:3) NOTE The still image resolution captured during the recording of a movie is the same as the video resolution. Using the pre-record function The Pre-record function ensures that you will not miss any critical recording opportunities, as movies are recorded 3 seconds before the OK button is pressed. To use the Pre-record function: 1 Press the Pre-record button ( ) while in Record mode. The Pre-record icon( ) appears on the LCD touch screen. 2 Aim the camcorder at the subject. 3 Press the OK button to start recording. (The camcorder records 3 seconds before you actually press the OK button.) To use the function again, repeat steps 1-3 above.

25 Record Mode Picture recording 25 NOTE The Time Lapse function cannot be used when the Pre-Record function is activated. Picture recording In Picture Record mode (The Picture Record LED indicator is lit), press the OK button to take a picture. Press Playback button to view the picture. The three resolution settings available are: Image Quality High Quality: 16 Mega Pixels Standard Quality: 5 Mega Pixels Low Quality: 3 Mega Pixels Taking close up pictures/movies Slide the macro switch to change the focus range for different distances of objects. To take close-up pictures: 1 Slide the Macro switch to Macro ( ). 2 Press the Record button to start recording a movie or to take a still picture. In Macro mode, the macro icon ( ) appears on the LCD touch screen. NOTE Remember to turn the macro switch back to Normal ( are not taking close-up pictures. ) when you

26 26 Record Mode Using the Flash or digital light function Using the Flash or digital light function The camcorder has three Flash settings and one additional setting that allows you to increase the brightness of an object, which may be dark or in shadow. To use light function: 1 Flash Auto ( ): The flash fires automatically according to light conditions. Use this mode for general photography, (Picture Recording only). 2 Red Eye Reduction ( ): The pre-flash will fire to reduce the red-eye effect, (Picture Recording only). 3 Digital Light ( ): Extends the dynamic range for backlight and high contrast sensitivity, so that objects will be brighter and clearer. 4 Flash Off ( ): The flash will not fire under any circumstances. Use this mode when taking pictures in a place where flash photography is prohibited, or when the subject is distant (beyond the range of the flash), (Picture Recording only). NOTE The flash will be disabled automatically when battery power is low ( ). Using zoom The zoom magnifies images when recording movies or taking pictures. 1 To zoom in/out, press the Tele/Wide button. 2 The zoom can be set from 1X~5X (5X Optical zoom and 1X Digital zoom)/1x~20x (5X Optical zoom and 4X Digital zoom)

27 Record Mode Record menu options 27 Record menu options Movie Record mode menu Movie Resolution White Balance Scene Effect FHD (1080p/30fps) HD (720p/30fps) WVGA 60 VGA (4:3) Auto Daylight Fluorescent Tungsten Auto Skin Night Backlight B/W (Black/White) Classic Negative Stabilization Macro mode Motion Detect (Motion Detection) Slow Motion Time Lapse Picture record mode menu Movie Resolution White Balance Scene Effect High (16 MP) Standard (10 MP) Low (3 MP) Auto Daylight Fluorescent Tungsten Record mode operations Auto Skin Night Backlight B/W (Black/White) Classic Negative Self-Timer Macro mode ISO Operation 1 Touch the Menu ( ) icon in Record mode. The wheel menu displays. Screen

28 28 Record Mode Movie resolution Operation 2 Lightly scroll the on-screen wheel menu with your finger to view the options: Resolution, Scene, Effect, White Balance, Scene, and Setting. 3 As you scroll, the submenus for each option will display. 4 Touch the specific option you want to adjust, then touch OK to confirm the setting. 5 You may also touch the Return icon ( ) to exit without any making any changes. 6 Touch the on-screen Page Up ( ) and Page Down ( ) icons to scroll through the pages. Screen Movie resolution The four resolution settings available are: FHD (1080p/30fps): Record movies at 1920 x1080p 30 resolution. HD (720p/30fps): Record movies at 1280 x 720p 30 resolution. WVGA 60: Record movies at 848 x 480p 60 resolution. VGA(4:3): Record movies at 640 x 480p 30 resolution. Operation 1 In Movie Record mode, touch the on-screen Menu ( ) icon to display the wheel menu. 2 Scroll to select Resolution. The Resolution submenu displays. 3 Touch the desired option to select it. 4 Touch OK to confirm the setting. Screen

29 Record Mode Picture resolution 29 Picture resolution The three resolution settings available are: High (16 MP): Take pictures at 4608 x 3456, 16 MP quality. Standard (10 MP): Take pictures at 3644 x 2748, 10 MP quality. Low(3 MP): Take pictures at 2048 x 1536, 3 MP quality. Operation 1 In Picture Record mode, touch the on-screen Menu ( ) icon to display the wheel menu. 2 Scroll to select Resolution. The Resolution submenu displays. 3 Touch the desired option to select it. 4 Touch OK to confirm the setting. Screen White balance The camcorder automatically adjusts the color balance of images. There are three manual white balance settings available in addition to the Auto setting. Auto: The camcorder automatically adjusts white balance. Daylight: Use in outdoor conditions. Fluorescent: Use under fluorescent light condition. Tungsten: Use under tungsten light condition. Operation 1 In Movie/Picture Record mode, touch the on-screen Menu ( ) icon to display the wheel menu. 2 Scroll to select White Balance. The White Balance submenu displays. 3 Touch the desired option to select it. 4 Touch OK to confirm the setting. Screen

30 30 Record Mode White balance Scene You can select modes according to the scene and conditions. Auto: Take or record without applying any special effects to the image. Skin: Take or record with an effect that makes skin tones more natural. Night: Use Night mode for night scenes or low light conditions. Backlight: You can take pictures or record when bright light is behind the subject. B/W: The image is converted to black-and-white. Classic: The image is converted to a sepia look. Negative: The image is converted to a negative version of the original. Operation 1 In Movie/Picture Record mode, touch the on-screen Menu ( ) icon to display the wheel menu. 2 Scroll to select Scene. The Scene submenu displays. 3 Touch the desired option to select it. 4 Touch OK to confirm the setting. Screen NOTE To avoid blurry pictures, place the camcorder on a flat, steady surface, or use a tripod when taking photos in Night Mode.

31 Record Mode Movie effects 31 Movie effects Operation 1 In Movie Record mode, touch the on-screen Menu ( ) icon to display the wheel menu. 2 Scroll to select Effect. The Effect submenu displays. 3 Touch the desired option to select it. 4 The Movie Effect submenu contains five options to select from: Stabilization, Macro mode, Motion Detection, Slow Motion and Time Lapse. Screen Stabilization Your camcorder provides a feature that steadies the image to help reduce shaking and create clearer videos. Operation 1 In the Effect submenu, touch to select Stabilization, which will display the options screen. 2 Touch the desired option to select it. 3 Touch OK to confirm the setting. Screen NOTE Stabilization does not apply to the FHD (1080p/30fps) WVGA 60 settings.