FICHA TÉCNICA TECHNICAL DATA SHEET: BTS-6 VENTAJAS BENEFITS Homologado CE parte 6 (ETA 16-0848) CE homologated Part 6 (ETA 16-0848) Apto para hormigón fisurado y no fisurado Allowed for cracked and non cracked concrete Multiaplicación - Multi-application Puedes fijar abrazaderas M6/M8, fijar soportes o perfiles, bajar varilla M6/M8 You can install M6-M8 Clamps, fix supports or channels, install threaded bars Doble empotramiento (35/50mm) Double embedment (35/50mm) Sin expansión - No expansión Menor distancia al borde y entre fijaciones Lower edge distance and spacing between anchors. Anclaje formado por un solo componente One piece anchor. Reducido par de apriete con llave de vaso que permite el montaje de las 3 referencias, tornillo, espárrago y tuerca Low install torque using nut setter, that allow the installation of three references, screw, rod and nut. Desmontable Removable. Resistente a vibraciones High resistance to vibrations. Carga inmediata, no necesita tiempo de espera Instantaneous load. No need to wait. Permite instalación con taladro, usando la broca, el adaptador y la llave de vaso Allows the installation with drilling machine using the drill, the adapter and nut setter. Homologado al fuego Fire homologated C/ Garrotxa, naves 10-22 Foto Producto / Product photo Homologaciones / Homologations APLICACIONES APPLICATIONS. Perfiles metálicos y soportes / Metal channels and supports Mobiliario urbano / Urban furniture Fijación de varillas / Threaded rods fixing. Montaje de abrazaderas M6 y M8 / To install M6 and M8 clamps TDS-1
CARACTERÍSTICAS FEATURES Material / Material Fabricado en acero templado - Manufactured in hardened steel. Baño / Coating Recubrimiento orgánico láminas Zn-Al gris >240HNS Organic coating Zn-Al flakes >240H in SST GAMA -RANGE : Cotas principales (mm) - Main dimensions (mm) Referencia Reference Llave Wrench Øcabeza øhead Long. Tuerca Nut length BTS-B SW10 14 - BTS-PT TX30 14.5 - BTS-H M6 1/4 SW10 14 6 BTS-H M8 SW10 14 8 BTS-H M10-3/8 SW 3 17 10 BTS-E M6 1/4 SW10 14 6 BTS-E M8 5/16 SW10 14 8 TDS-2
PROCEDIMIENTO DE INSTALACIÓN / INSTALLATION PROCEDURE Con set adaptador- with set adaptor Broca ø6 / ø6 Drill Adaptador / Adapter Llave de vaso / Nut La fijación más rápida en hormigón, solo tres pasos: taladrar, limpiar, roscar. En caso de utilizar un taladro, necesitas el adaptador para roscar el anclaje. Fastest anchor in concrete, only three steps: drill, clean and thread. If you use a drill machine, you have to use adaptor to thread the anchor. PARÁMETROS DE INSTALACIÓN / INSTALLATION PARAMETERS TDS-3
Parámetros / Parameters 50mm 35mm Øagujero do Hole diameter do Profundidad empotramiento hnom Embedment depth hnom Profundidad efectiva heff Effective depth heff Distancia característica entre anclajes Scr (mm) Characteristhic spacing between anchor S cr (mm) Distancia característica al borde Ccr (mm) Characteristhic edge distance C cr (mm) Distancia mínima entre anclajes Smin (mm) Mínimum spacing between anchor S min (mm) Distancia mínima al borde Cmin (mm) Minimum edge distance C min (mm) Espesor mín. hormigón hmin (mm) Minimum concrete thickness hmin (mm) Par apriete máximo (Nm) Max. Installation torque (Nm) 6mm 6mm 50mm 35mm 39 26 160 160 80 80 40 40 40 40 100 100 15 15 MATERIALES BASE / BASE MATERIAL Hormigón / Concrete Ladrillo macizo / Solid brick CARGAS PERMITIDAS / PERMISSIBLE LOADS. Cargas permitidas (kn) / Permissible loads (kn) Esfuerzo a tracción y cizalla hormigón C20/25 Pull out and shear load in C20/25 Esfuerzo a tracción y cizalla hormigón C50/60 Pull out and shear load in C50/60 50mm 35mm 1.90 0.71 2.38 1.03 Notas / notes: Permitida (con Factor de seguridad total incluido) Permissible (safety factor is included). TDS-4
CARGAS HOMOLOGADAS AL FUEGO / FIRE RESISTANCE LOADS. ApoloMEA BTS-6 Fire resistance class Hnom 50mm R 30 FRk,fi [kn] 0,2 Resistencia característica - Characteristic resistacne R 60 FRk,fi [kn] 0,2 R 90 FRk,fi [kn] 0,1 R 120 FRk,fi [kn] 0,1 Distancias bajo exposición al fuego Distances under fire exposure Distance entre anclajes R30-R120 - Spacing distance R30-R120 Scr,fi [mm] 160 Distance al borde R30-R120 - Edge distance R30-R120 Ccr,fi [mm] 80 La distancia al borde debe ser 300mm en caso de que el fuego ataque por más de una dirección The edge distance shall be 300mm, in case of fire attack from more tan one side. TDS-5