MOTOR ORBITAL OMP DANFOSS OMP Technical Information A Wide Range of Hydraulics Motors

Transcripción

1 Wide Range of Hydraulics Motors F Wide Range of Hydraulic Motors Sauer-Danfoss is a world leader within production of low speed hydraulic motors with high torque. We can offer more than 3 different hydraulic motors, categorised in types, variants and sizes (incl. different shaft versions). The motors vary in size (rated displacement) from 8 cm3 [.5 in3] to 8 cm3 [48.9 in3] per revolution. Speeds range up to approx. 25 min-1 (rpm) for the smallest type and up to approx 6 min-1 (rpm) for the largest type. Maximum operating torques vary from 13 Nm [115 lbf in] to 27 Nm [24. lbf in] (peak) and maximum outputs are from 2. kw [2.7 hp] to 7 kw [95 hp]. Characteristic features: Smooth running over the entire speed range Constant operating torque over a wide speed range High starting torque High return pressure without the use of drain line (High pressure shaft seal) High efficiency Long life under extreme operating conditions Robust and compact design High radial and axial bearing capacity For applications in both open and closed loop hydraulic systems Suitable for a wide variety of hydraulics fluids

2 Tech Wide Range of Hydraulics Motors The programme is characterised by technical features appealing to a large number of applications and a part of the programme is characterised by motors that can be adapted to a given application. daptions comprise the following variants among others: Motors with corrosion resistant parts Wheel motors with recessed mounting flange OMP, OMR- motors with needle bearing OMR motor in low leakage version OMR motors in a super low leakage version Short motors without bearings Ultra short motors Motors with integrated positive holding brake Motors with integrated negative holding brake Motors with integrated flushing valve Motors with speed sensor Motors with tacho connection ll motors are available with black finish paint The Sauer Danfoss LSHT motors are used in the following application areas: Construction equipment gricultural equipment Material handling & Lifting equipment Forestry equipment Lawn and turf equipment Special purpose Machine tools and stationary equipment Marine equipment Survey of Literature with Technical Data on Sauer-Danfoss Hydraulic Motors Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is divided into 8 individual subcatalogues: General information on Sauer-Danfoss hydraulic motors: function, use, selection of hydraulic motor, hydraulic systems, etc. Technical data on small motors: OML and OMM Technical data on medium sized motors: OMP, OMR and OMH Technical data on medium sized motors: DH and DS Technical data on medium sized motors: OMEW Technical data on large motors: OMS, OMT and OMV Technical data on large motors: TMK Technical data on large motors: TMT Technical data on large motors: TMVW general survey brochure on Sauer-Danfoss hydraulic motors gives a quick motor reference based on power, torque, speed and capabilities

3 Techn Wide Range of Hydraulics Motors Speed, Torque and Output The bar diagrams above are useful for a quick selection of relevant motor size for the application. The final motor size can be determined by using the function diagram for each motor size. OMP and OMPW can be found on pages 2-26 OMR and OMRW can be found on pages OMH can be found on pages The function diagrams are based on actual tests on a representative number of motors from our production. The diagrams apply to a return pressure between 5 and 1 bar [ and 15 psi] when using mineral based hydraulic oil with a viscosity of 35 mm 2 /s [165 SUS] and a temperature of 5 C [12 F]. For further explanation concerning how to read and use the function diagrams, please consult the paragraph "Selection of motor size" in the technical information "General Orbital Motors" 52L232 Rev. B

4 Versions Versions Mounting flange Spigot diam,eter (front /rear end) Bolt circle diameter (BC) Shaft Port size European version US version Side port version End port version Flange port version Standard shaft seal High pressure shaft seal Drain connection Check valve Main type designation G ½ l l l No No OMP Cyl. 25 mm G ½ l l l Yes No OMP G ½ l l l Yes Yes OMP 2 hole oval flange (2-flange) 82.5 mm [3.25 in] 16.4 mm [4.2 in] Cyl. 1 inch G ½ l l l No No OMP G ½ l l l Yes No OMP 7 /8-14 UNF l l l Yes Yes OMP Splined 1 inch G ½ l l l No No OMP G ½ l l l Yes No OMP 4 hole oval flange (4-flange) 82.5 mm [3.25 in] 16.4 mm [4.2 in] Cyl. 32 mm G ½ l l l Yes Yes OMP Square flange (C-flange) 44.4 mm [1. in] 82.5 mm [3.25 in] Cyl. 25 mm Cyl. 1 inch G ½ l l l Yes Yes OMP 7 /8-14 UNF l l l Yes Yes OMP 1 /2-14 NPTF l l l Yes Yes OMP Wheel 8 mm [3.15 in] 13 mm [4.6 in] OMP motors with corrosion resistant parts 2 hole oval flange (2-flange) 82.5 mm [3.25 in] OMP motors with needle bearings 2 hole oval flange (2-flange) Wheel 82.5 mm [3.25 in] 8 mm [3.15 in] 16.4 mm [4.2 in] 16.4 mm [4.2 in] 13 [4.6] OMP motors with free running gerotor 2 hole oval flange (2-flange) 82.5 mm [3.25 in] 16.4 mm [4.2 in] Cyl. 25 mm G ½ l l l Yes Yes OMPW Cyl. 25 mm G ½ l l l Yes Yes OMP C Cyl. 25 mm G ½ l l l Yes Yes OMP N Tap mm G ½ l l l Yes Yes OMPW N Cyl. 25 mm G ½ l l l Yes No OMP Functions diagram - see page: Features available (options) : Low leakage (low speed valve) Speed sensor Viton shaft seal Reverse rotation Painted

5 Code Numbers Code Numbers Displacement [cm 3 ] Code numbers Technical data - Page Dimensions - Page * OMP motors with corrosion resistant parts OMP motors with needle bearings OMP motors with free running gerotor * Motor painted black Ordering dd the four digit prefix 151- to the four digit numbers from the chart for complete code number. Example: for an OMP 2 with 2 flange, cyl. 1 in shaft, port size G 1 /2 and high pressure shaft seal. Orders will not be accepted without the four digit prefix

6 Technical Data Technical data for OMP with 25 mm and 1 in cylindrical shaft Type OMP OMP OMP OMP OMP OMP OMP Motor size Geometric displacement cm 3 [inch] 25. [1.53] 32. [1.96] 4. [2.45] 48.6 [2.97] 59.1 [3.61] 77.8 [4.76] 97.3 [5.95] Max. speed min -1 cont [rpm] int. 1 ) Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque bar [psi] N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] standard free running gerotor at max. press drop cont. N m [lbf in] at max. press.drop int. 1 ) N m [lbf in] cont. 33 [29] int. 1 ) 47 [42] 67 peak 2) [59] cont. 4.5 [6. int. 1 ) 6.1 [8.2] cont. 1 [145] int. 1 ) 14 [23] peak 2) [326] cont. 4 [1.6] int. 1 ) 45 [11.9] 1 [145] 43 [38] 61 [54] 86 [76] 5.8 [7.8] 7.8 [1.5] 1 [145] 14 [23] [326] 5 [13.2] 55 [14.5] 1 [145] 52 [46] 74 [66] 17 [95] 7. [9.4] 1.6 [14.2] 1 [145] 14 [23] [326] 6 7 [18.5] 1 [145] 93 [82] 12 [16] 14 [124] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 1 [145] 115 [12] 14 [124] 18 [159] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 1 [145] 15 [133] 19 [168] 22 [195] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 1 [145] [27] 4 [35] 4 [35] 55 [49] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 45 [4] 63 [56] 8 [71] 1 [89] 1 [885] 12 [16] 135 [12] 17 [151] 19 [168] 23 [24] 27 [239] 11. [14.8] 13. [17.4] 14 [23] 1 [254] [326] 6 1 [145] 2 [29] 17 [151] 21 [186]

7 Technical Data Technical data for OMP with 25 mm and 1 in cylindrical shaft (continued) Type OMP OMP OMP OMP OMP OMP OMP Motor size Geometric displacement cm 3 [inch] [6.87] 125. [7.65] [9.53] [11.91] [14.83] 36.1 [18.73] [23.82] Max. speed min -1 cont [rpm] int 1 ) Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque bar [psi] N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] standard free running gerotor at max. press drop cont. N m [lbf in] at max. press.drop int. 1 ) N m [lbf in] cont. 215 [19] int. 1 ) 26 [23] 32 peak 2) [283] cont. 1 [13.4] int. 1 ) 12. [16.1] cont. 14 [23] int 1 ) 1 [254] peak 2) [326] cont. 6 int. 1 ) 1 [145] - 19 [168] 24 [212] 24 [212] 29 [257] 37 [328] 1 [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 9 [13] 2 [29] 21 [186] 27 [239] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 3 [266] 37 [328] 43 [381] 1 [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 7 [1] 2 [29] 28 [248] 35 [31] 3 [266] 38 [336] 54 [478] 8. [1.7] 11. [14.8] 115 [167] 15 [218] [326] 6 5 [] 2 [29] 27 [239] 36 [319] 3 [266] 41 [363] 55 [487] 6. [8.1] 9. [12.1] 9 [131] 125 [181] 18 [261] 6 5 [] 3 [266] 39 [345] 6 [531] 5. [6.7] 7. [9.4] [19] 1 [145] 16 [232] 6 5 [] 3 [266] 42 [372] 6 [531] 4. [5.4] 6. [8.1] 6 [87] 8 [116] 13 [189] 6 5 [] [248] 39 [345] 28 [248] 37 [328] 28 [248] 4 [354]

8 Technical Data Technical data for OMP with 1 in splined and 28.5 mm tapered shaft Type OMP OMP OMP OMP OMP OMP OMP OMP OMP Motor size Geometric displacement cm 3 [inch] 48.6 [2.97] 77.8 [4.76] 97.3 [5.95] 125. [7.65] [9.53] [11.91] [14.83] 36.1 [18.73] [23.82] Max. speed min -1 cont [rpm] int 1) Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] bar [psi] at max. press drop cont. N m [lbf in] at max. press.drop int. 1) 93 cont. [82] 12 int. 1) [16] 14 peak 2) [124] 1. cont. [13.4] 12. int. 1) [16.1] 14 cont. [23] 1 int1) [254] peak 2) [326] 6 cont. int. 1) 1 [145] 8 [71] 1 15 [133] 19 [168] 22 [195] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 1 [145] 135 [12] [168] 23 [24] 27 [239] 11. [14.8] 13 [17.4] 14 [23] 1 [254] [326] 6 1 [145] 17 [151] [212] 29 [257] 37 [328] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 9 [13] 21 [186] 27 N m [lbf in] [89] [151] [186] [239] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 3 [266] 37 [328] 43 [381] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 7 [1] 28 [248] 35 [31] 36 [319] 45 [398] 54 [478] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 5 [] 34 [31] 42 [372] 36 [319] 46 [47] 55 [487] 8. [1.7] 1.5 [14.1] 15 [152] 14 [23] 18 [261] 6 5 [] 33 [292] 44 [389] 36 [319] 47 [416] 54 [478] 6. [8.] 7.5 [1.1] 9 [131] 12 [174] 16 [232] 6 5 [] 34 [31] 45 [398] 36 [319] 46 [47] 56 [496] 5. [6.7] 6. [8.] 7 [12] 9 [131] 13 [189] 6 5 [] 345 [35] 425 [376]

9 Technical Data Technical data for OMP with 32 mm cylindrical shaft Type OMP OMP OMP OMP OMP OMP OMP OMP OMP Motor size Geometric displacement cm 3 [inch] 48.6 [2.97] 77.8 [4.76] 97.3 [5.95] 125. [7.65] [9.53] [11.91] [14.83] 36.1 [18.73] [23.82] Max. speed min -1 cont [rpm] int 1) Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] bar [psi] at max. press drop cont. N m [lbf in] at max. press.drop int. 1) N m [lbf in] 93 cont. [82] 12 int. 1) [16] 14 peak 2) [124] 1. cont. [13.4] 12. int. 1) [16.1] 14 cont. [23] 1 int1) [254] peak 2) [326] 6 cont. int. 1) 1 [145] 8 [71] 1 [89] 15 [133] 19 [168] 22 [195] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 1 [145] 135 [12] 17 [151] 19 [168] 23 [24] 27 [239] 11. [14.8] 13. [17.4] 14 [23] 1 [254] [326] 6 1 [145] 17 [151] 21 [186] 24 [212] 29 [257] 37 [328] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 9 [13] 21 [186] 27 [239] 3 [266] 37 [328] 43 [381] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 7 [1] 28 [248] 35 [31] 36 [319] 45 [398] 54 [478] 1. [13.4] 12. [16.1] 14 [23] 1 [254] [326] 6 5 [] 34 [31] 42 [372] 46 [47] 57 [55] 67 [593] 9.5 [12.7] 12. [16.1] 14 [23] 1 [254] [326] 6 5 [] 42 [372] 53 [469] 47 [416] 62 [549] 82 [726] 7.5 [1.1] 9. [12.1] 12 [174] 16 [232] [326] 6 5 [] 46 [47] 6 [531] 49 [434] 63 [58] 84 [744] 6.5 [8.7] 7.5 [1.1] 95 [138] 125 [181] 18 [261] 6 5 [] 46 [47] 6 [531] Type bar [psi] Max. inlet pressure OMP 25-4 bar 2 [psi] int. 1) [29] bar [psi] peak 2) [326] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. cont 1 [254] Max.return pressure with drain line 1 [254] 2 [29] [326]

10 Technical Data - Max. Permissible Shaft Seal Pressure OMP with HIGH Pressure Shaft Seal (HPS) OMP with HPS and without drain connection: The shaft seal pressure equals the average of input pressure and return pressure. OMP with HPS and drain connection: The shaft seal pressure equals the pressure in the drain line. P seal = P in + P return 2 Max. permissible shaft seal pressure psi 36 bar Ø25 mm-ø1 -Ø1 splined shaft int. operation 1) max. min -1 (rpm) OMP with Standard Shaft Seal OMP with standard shaft seal, check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line OMP with standard shaft seal, check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. Max. return pressure without drain line or max. pressure in the drain line psi 2 16 bar int. operation 1) 12 int. operation 1) 8 5 Ø25 mm - Ø1-1 splined - 1 and 28.5 mm tapered shaft 4 25 Ø32 mm shaft ) Intermittent operation: the permissible values may occur for max. 1% of every minute. max. min -1 (rpm)

11 Technical Data Pressure Drop in Motor p p psi 4 35 bar 3 25 B Q l/min Q US gal/min The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS] : OMP 5-4 B: OMP 25-4 / OMPW Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [-15 psi]. Pressure drop bar [psi] 1 [145] 14 [23] Viscosity mm 2 /s [SUS] 2 [1] 35 [165] 2 [1] 35 [165] Oil flow in drain line l/min [US gal/min] 2.5 [.66] 1.8 [.78] 3.5 [.93] 2.8 [.74] Direction of Shaft Rotation

12 Technical Data The permissible radial shaft load (P R ) depends on Speed (n) Distance (L) from the point of load to the mounting flange Mounting flange version Shaft version Mounting flange Shaft version Permissible shaft load (P R ) - l in mm Permissible shaft load (P R ) - l in inch 4-oval flange** 2-hole oval flange (European version) 25 mm cylindrical shaft 1 in cylindrical shaft 1 in splined shaft 8 25 N* n 95 + L lbf* n L 4-hole oval flange Square flange** 2-hole oval flange (US-version) 32 mm cylindrical shaft 25 mm cylindrical shaft 8 18 N* n 95 + L lbf* n L 8 25 N* n 11 + L lbf* n L * n 2 min -1 [rpm]; 55 mm [2.2 in] n< 2 min -1 [rpm]; = > P Rmax = 8 N [18 lbf] ** For both European and US-version P R -2 (European-version) -4-2 (US-version) P R P R lbf N lbf 15 N N 44 lbf 3 [1.18] C min -1 (rpm) 24 [.94] 24 [.94] cylindrical shaft 32 mm [1.26 in] other shaft versions The curve shows the relation between P R and n when l = 3 mm [1.18 in] for motors with 2 (European version) and 4 oval mounting flange when l = 24 mm [.94 in] for motors with square mounting flange and 2 (US version) For applications with special performance requirements we recommend OMP with the output shaft running in needle bearings

13 Technical Data Permissible Shaft Load for OMP N Prad. lbf Prad. N mm Pmax. Pmax. 2 N = 45 lbf = 15 N 335 lbf min -1 2 min -1 8 min in The output shaft on OMP N can be offered in needle bearings. These bearings and the recessed mounting flange allow a higher permissible radial load in comparison to OMP motors. The permissible radial load on the shaft is shown for different speeds as a function of the distance from the mounting flange to the point of load application. Curve indicates the max. radial shaft load. ny shaft load exceeding the values quoted in curve will involve risk of breakage. The other curves apply to a B1 bearing life of 2 hours at the number of revolutions indicated by the curve letter. Mineral based hydraulic oil with a sufficient content of antiwear additives must be used. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital Motors" 52L232 Rev. B

14 Technical Data Permissible Shaft Load for OMPW with Slide Bearings Prad. lbf Prad. N 2 2 N Pmax. = lbf 16 Pmax. = 15 N lbf min -1 4 min min mm in The output shaft on OMPW can be offered in slide bearings similar to the other OMPmotors. The permissible higher radial load is therefore due to the recessed mounting flange moving the point of load closer to the motor bearings. The permissible radial load on the shaft is shown for different speeds as a function of the distance from the mounting flange to the point of load application. The curves are not based on calculations of B1 bearing life. They represent absolute limits that must not be exceeded. Curve indicates the max. radial shaft load. ny shaft load exceeding the values quoted in curve will involve risk of breakage

15 Technical Data Permissible Shaft Load for OMPW N with Needle Bearing Prad. lbf Prad. N 2 2 N Pmax. = lbf Pmax. = 15 N lbf min min min mm in The output shaft on OMPW N can be offered in needle bearings. These bearings and the recessed mounting flange allow a higher permissible radial load in comparison to OMP motors. The permissible radial load on the shaft is shown for different speeds as a function of the distance from the mounting flange to the point of load application. Curve indicates the max. radial shaft load. ny shaft load exceeding the values quoted in curve will involve risk of breakage. The other curves apply to a B1 bearing life of 2 hours at the number of revolutions indicated by the curve letter. Mineral based hydraulic oil with a sufficient content of antiwear additives must be used. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital Motors" 52L232 Rev. B

16 Function Diagrams Function Diagrams lbf in 45 Nm 5 Q=5 l/min [1.3 US gal/min] OMP 25 1 l/min [2.6 US gal/min] 15 l/min [4. US gal/min] 2 l/min [5.3 US gal/min] 25 l/min [6.6 US gal/min] 3 l/min [7.9 US gal/min] 35 l/min [9.2 US gal/min] 4 l/min [1.6 US gal/min] Q=45 l/min [11.9 US gal/min] kW N=6hp N=6kW p=14 bar 23 psi 12 bar 174 psi hp 1 bar 145 psi N=.5hp 1hp.5kW N=.25kW 2hp 1kW 2kW η t =73% 65% η t =5% 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) lbf in 65 6 Nm 7 Q=5 l/min [1.3 US gal/min] OMP 32 1 l/min [2.6 US gal/min] 15 l/min [4. US gal/min] 2 l/min [5.3 US gal/min] 25 l/min [6.6 US gal/min] 3 l/min [7.9 US gal/min] 35 l/min [9.2 US gal/min] 4 l/min [1.6 US gal/min] 45 l/min [11.9US gal/min] 5 l/min [13.2 US gal/min] Q=55 l/min [14.5 US gal/min] N=.5 hp N=.5kW 1kW η t =78% 2kW 2hp 4hp 4kW N=6hp N= 6kW p=14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi hp 73% 65% η t =5% p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

17 Function Diagrams Function Diagrams lbf in 7 Nm 8 OMP 4 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] Q=7 l/min [18.5US gal/min] hp N=.5hp 1kW η t =78% N=.5kW 2hp 2kW 4hp 6hp 4kW % 7% 8hp N= 1hp 6kW 6% 8kW η t =5% N= 1kW p=14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) OMP 5 lbf in 11 1 Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] N=1kW N=1hp 2kW 2hp 4hp 6hp 8hp 4kW η t =% 7% η t =5% 8kW 1hp 6kW 6% 1kW N=12hp N=12kW p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

18 Function Diagrams Function Diagrams OMP 6 under preparation OMP 8 lbf in 18 Nm 2 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] N=1kW N=1hp 2kW 2hp 4hp 1hp 6hp 8hp 4kW η t =% η t =5% N=12hp 8kW 6kW 7% N=12kW 6% 1kW p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

19 Function Diagrams Function Diagrams OMP 1 lbf in 22 2 Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] N=1kW N=1hp 2kW 2hp 4hp 7% 6hp 4kW η t =78% % 6% η t =5% 6kW 8hp 8kW 1kW N=12hp 1hp N=12kW p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) OMP 11 under preparation Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page 1-13 Intermittent pressure drop and oil flow must not occur simultaneously

20 Function Diagrams Function Diagrams lbf in 3 Nm 32 OMP 125 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] hp N=1kW N=1hp 2kW 4hp 8hp 4kW η t =78% % 7% 6% η t =5% 6kW 6hp N=1kW 8kW N=1hp p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) lbf in 36 Nm 4 OMP 16 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] kW N=1kW N=1hp 2hp 4kW 4hp 6hp 1hp 6kW 8hp η t =78% % 7% 6% η t =5% N=12hp 8kW 1kW N=12kW p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

21 Function Diagrams Function Diagrams lbf in 45 Nm 5 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] OMP 2 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] kW 2hp N=1kW N= 1hp 4kW 4hp η t =77% % 7% 6% η t =5% 8hp 6hp N=1kW 8kW 6kW 1hp p=1 bar 254 psi 15 bar 218 psi 14 bar 23 psi 115 bar 167 psi 1 bar 145 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) lbf in 55 5 Nm 6 55 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] OMP 25 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] hp N= 1kW N=1hp 2kW 4hp η t =8% 6hp % 7% 6% 4kW η t =5% 6kW 8hp 8kW N=1hp N=1kW p=1 bar 254 psi 16 bar 232 psi 14 bar 23 psi 125 bar 181 psi 1 bar 145 psi 85 bar 123 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

22 Function Diagrams Function Diagrams lbf in 6 55 Nm 64 OMP 315 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] hp N=1hp 2kW η t =73% N=1kW 4hp 7% 6% η t =5% 6hp 4kW N=8kW 8hp 6kW N= 1hp p=16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 85 bar 123 psi 7 bar 12 psi 5 bar 73 psi p= 3 bar 44 psi min -1 (rpm) OMP 4 lbf in Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 7 l/min [18.5US gal/min] Q= l/min [19.8 US gal/min] hp N=1kW N=1hp 2kW η t =8% % 7% 6% η t =5% 4hp 4kW N=6kW N=8hp 6hp p=125 bar 181 psi 11 bar 16 psi 95 bar 138 psi 8 bar 116 psi 65 bar 94 psi 55 bar 8 psi 45 bar 65 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 7. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page Intermittent pressure drop and oil flow must not occur simultaneously

23 Shaft Version Shaft Version : Cylindrical shaft 25 mm D: Parallel key DIN 6885 Ø28.56 [1.124] [1.724] 42.5 [1.673] R.5 [.2] 32. [1.26] 31.7 [1.248] min. 18 [.71] max. 6 [.24] M8 Ø25.15 [.985] Ø25.2 [.984] 6.4 [.252] 4.4 [.173] 28. [1.12] 27.7 [1.9] - 8. [.315] [.314] D 43.8 [1.724] 42.5 [1.673] min. 18 [.71] B: Cylindrical shaft 1 in E: Parallel key 1 /4 1 /4 1 1 /4 in B.S. 46 B Ø28.56 [1.124] 45 R.5 [.2] 31. [1.25] [1.238] M8 max. 6 [.24] Ø25.4 [1.] Ø25.38 [.999] 5.5 [.217] 3.5 [.138] [1.11] [1.1] [.252] 6.35 [.25] E 38.8 [1.528] 36.8 [1.448] 14 [.55] min. 18 [.71] US version C: Cylindrical shaft 1 in F: Parallel key 1 /4 1 /4 1 1 /4 in B.S. 46 C Ø28.56 [1.124] 45 R.5 [.2] 31. [1.25] [1.238] max. 6 [.24] ¼ -2 UNC Ø25.4 [1.] Ø25.38 [.999] 5.5 [.217] 3.5 [.138] [1.11] [1.1] [.252] 6.35 [.25] F

24 Shaft Version Shaft Version D: Cylindrical shaft 32 mm I: Parallel key DIN 6885 D Ø35. [1.378] [2.242] [2.179] R.5 [.2] min. 18 [.71] max. 6 [.24] M8 Ø32.18 [1.261] Ø32.2 [1.26] 35. [1.38] 34.8 [1.37] [1.772] 44.7 [1.76] 5.5 [.217] 4.5 [.177] 1. [.394] [.392] I E: Splined shaft B.S. 259 (SE 6 B) Straight-sided, bottom fitting, dep. Fit 2 Nom. size 1 in * Deviates from BS 259 (SE 6B) E Ø28.56 [1.124] [1.724] 42.5 [1.673] R.5 [.2] M8 min. 18 [.71] max. 6 [.24] Ø [.998] Ø [.998] 6.2 [.247] 6.21 [.244] - *21.54 [.848] *21.4 [.843] R max [1.673] 27.4 [1.79] 25.4 [1.] 1.2 [.39]x45.8 [.31]x45 6x6 F: Tapered shaft H: DIN 937 NV 3 Tightening torque: 1 ± 1 N m [885 ± 88.5 lbf in] G: Taper 1:1 J: Parallel key B DIN 6885 F Ø28.56 [1.124] G H 24.4 [.961] 23.6 [.929] 2.5 [.87] Ø4.5 [.177] M2x1.5 [.59] ø44 [1.73] [.62] [.6] - 5. [.197] 4.97 [.196] J

25 Port Thread Versions Port Thread Versions B C min. 15 [.59] max. Ø21.5 [.846] Ø3.5 [1.2] Ø29.5 [1.161] G H 1. [.4] min [.657] max. 27 [1.6] 2x max 21.5 [.84] I : G main ports B: UNF main ports C: NPTF main ports G: ISO 228/1 - G 1 /2 H: 7 /8-14 UNF I: 1 /2-14 NPTF O-ring boss port D F E 12.2 [.473] 11.8 [.465] max..6 [.24] Ø18.5 [.728] Ø17.5 [.689] J min. 12 [.47] D: G drain port F: UNF drain port E: ISO 228/1 - G 1 /4 J: 7 /16-2 UNF O-ring boss port Manifold Mount European version 36 [1.42] L 2 [.79] 2 [.79] 2 [.79] L: see dimensional drawing for given OMP motor on pages [.79] 18 [.71] 18 [.71]

26 Dimensions - European Version Dimensions Side port version with 2 hole oval mounting flange (2-flange). Type OMP 25 OMP 32 OMP 4 OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 13. [5.12] 131. [5.16] 132. [5.2] 132. [5.2] 136. [5.35] [5.45] 142. [5.59] [5.77] [5.96] 158. [6.22] [6.56] [6.99] L 1 mm [in] 4.1 [.16] 5.2 [.2] 6.5 [.26] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] D: G 1 2; 15 mm [.59 in] deep E: M8; 13 mm [.51 in] deep (4 pcs.) L max [2.177] L 1 36 [1.42] 38 [1.5] max. 13 [4.6] 55 [2.17] Ø82.55 [3.25] Ø82.45 [3.246] 18 [.71] 18 [.71] max. Ø93 [3.66] 16.4 [4.189] 8 [.31] Ø13.5 [.53] E 16 [.63] D max. 133 [5.24]

27 Dimensions - European Version Dimensions Side port version with 2 hole oval mounting flange (2-flange). With drain connection. Type OMP 25 OMP 32 OMP 4 OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 13. [5.12] 131. [5.16] 132. [5.2] 132. [5.2] 136. [5.35] [5.45] 142. [5.59] [5.77] [5.96] 158. [6.22] [6.56] [6.99] L 1 mm [in] 4.1 [.16] 5.2 [.2] 6.5 [.26] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] max. 6 [.24] L max [2.177] L 1 36 [1.42] 38 [1.5] Ø82.55 [3.25] Ø82.45 [3.246] 18 [.71] 18 [.71] max. Ø93 [3.66] 16.4 [4.189] 8 [.31] 16 [.63] Ø13.5 [.53] E C C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep E: M8; 13 mm [.51 in] deep (4 pcs.) max. 13 [4.6] 55 [2.17] D max. 133 [5.24]

28 Dimensions - European Version Dimensions OMP C and OMP N Side port version with 2 hole oval mounting flange (2-flange). Type OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 132. [5.2] 136. [5.35] [5.45] 142. [5.59] [5.77] [5.97] 158. [6.22] [6.56] [6.99] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep E: M8; 13 mm [.51 in] deep (4 pcs.) max. 6 [.24] L max [2.177] L 1 36 [1.42] 38 [1.5] Ø82.55 [3.25] Ø82.45 [3.246] 18 [.71] 18 [.71] max. Ø93 [3.66] 16.4 [4.189] 8 [.31] 16 [.63] Ø13.5 [.53] E C max. 13 [4.6] 55 [2.17] D max. 133 [5.24]

29 Dimensions - European Version Dimensions End port version with 2 hole oval mounting flange (2-flange). Type OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] [5.] 15. [5.91] [6.1] [6.15] 16.4 [6.32] [6.52] [6.78] 18.5 [7.11] [7.54] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] max. 18 [4.25] max [2.177] 5 [.2] 62.4 [2.457] max. 1.5 [3.967] Ø82.55 [3.25] Ø82.45 [3.246] 8 [.31] 7.1 [.28] Ø13.5 [.53] C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep max. Ø93 [3.66] 16.4 [4.189] 55 [2.17] L 1 L 16 [.63] max. 9.1 [.358] C D max. 133 [5.24]

30 Dimensions - US Version Dimensions Side port version with 2 hole oval mounting flange (2-flange). Type OMP 25 OMP 32 OMP 4 OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 136. [5.35] 137. [5.39] 138. [5.43] 138. [5.43] 142. [5.59] [5.69] 148. [5.83] [6.] [6.2] 164. [6.46] [6.79] [7.23] L 1 mm [in] 4.1 [.16] 5.2 [.2] 6.5 [.26] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection G 7 /16 UNF; 12 mm [.47 in] deep D: G 7 /8-14 UNF; 16.7 mm [.66 in] deep E: M8; 13 mm [.51 in] deep (4 pcs.) max. 6 [.24] L max [1.81] 44 [1.73] L 1 36 [1.42] max. 13 [4.6] 55 [2.17] 18 [.71] Ø82.55 [3.25] Ø82.45 [3.246] max. Ø93 [3.66] 16.4 [4.189] max. 133 [5.24] 2.6 [.12] Ø13.5 [.53] D E C 18 [.71] 22 [.87]

31 Dimensions - European Version Dimensions Side port version with 4 hole oval mounting flange (4-flange). Type OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 132. [5.2] 136. [5.35] [5.45] 142. [5.59] [5.77] [5.97] 158. [6.22] [6.56] [6.99] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep E: M8; 13 mm [.51 in] deep (4 pcs.) max. 6 [.24] L max [2.689] L 1 36 [1.42] 38 [1.5] Ø82.55 [3.25] Ø82.45 [3.246] 18 [.71] 18 [.71] max. Ø93 [3.66] 16.4 [4.189] Ø13.5 [.53] E C max. 13 [4.6] 55 [2.17] 8 [.31] 16 [.63] 45 D max. 133 [5.24]

32 Dimensions - European Version Dimensions End port version with square mounting flange (C-flange). Type OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 152. [5.98] 156. [6.14] [6.24] [6.38] [6.55] [6.76] [7.1] [7.34] [7.78] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep E: M1; 15 mm [.59 in] deep (4 pcs.) L max [1.949] L 1 max. 9.1 [.358] max. 84 [3.31] C 55 [2.17] Ø44.45 [1.] Ø44.35 [1.746] max. Ø93 [3.66] D 2.5 [.98] R15 [.59] E max. 84 [3.31]

33 Dimensions - US Version Dimensions Side port version with square mounting flange (C-flange). Type OMP 5 OMP 8 OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 132. [5.2] 136. [5.35] [5.45] 142. [5.59] [5.77] [5.97] 158. [6.22] [6.56] [6.99] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection 7 /16-2 UNF; 12 mm [.47 in] deep D: 7 /8-14 UNF; mm [.66 in] deep or 1 /2-14 NPTF E: 3 /8-16 UNC; 15 mm [.59 in] deep (4 off) F: M8; 13 mm [.51 in] deep (4 pcs.) max [1.823] L 6 [.24] 44 [1.73] 36 [1.42] L 1 max. 13 [4.6] max. 84 [3.31] 55 [2.17] Ø44.45 [1.] Ø44.35 [1.746] 18 [.71] 18 [.71] max. Ø93 [3.66] Ø82.55 [3.25] 2.5 [.298] D F C R15 [.59] E max. 84 [3.31]

34 Dimensions - European Version Dimensions OMPW and OMPW N wheel motor Output shaft.max. Cylindrical shaft 25 mm [.98 in] Tapered shaft mm [1.12 in] Type OMP 5 OMP 8. OMP 1 OMP 125 OMP 16 OMP 2 OMP 25 OMP 315 OMP 4 Max. L mm [in] 71.8 [2.83].7 [2.98] 78.3 [3.8] 81.6 [3.21] 86.1 [3.39] 91.3 [3.6] 97.8 [3.85] 16.2 [4.18] [4.62] mm L 2 [in] max. 115 [4.53] max [4.64] L 1 mm [in] 6.5 [.26] 1.4 [.41] 13. [.51] 16.7 [.66] 2.8 [.82] 26. [1.2] 32.5 [1.28] 4.9 [1.61] 52. [2.5] C: Drain connection G ¼; 12 mm [.47 in] deep D: G ½; 15 mm [.59 in] deep E: M1; 2 mm [.79 in] deep (4 pcs.) L max. 6 [.24] L 2 D L 1 R.5 [.2] max. max. 12 [4.2] Ø8. [3.15] Ø [3.148] C max. 87 [3.43] max. 17 [4.21] 55 [2.17] 7.25 [.285] E 13 [4.6] max. 127 [5.] max. 69 [2.72] 2 [.79] 4 [1.57] Ø79.2 [3.118] Ø78.8 [3.12] 18.5 [.728] 18.5 [.728] max 81 [3.19]

35 Weight of Motors Weight of Motors Code no Weight kg [lb] [15.2] [15.4] [16.5] [17.6] [18.7] [14.8] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [12.3] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [12.1] [12.1] [12.3] [14.8] [15.2] [15.4] [16.5] Code no Weight kg [lb] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [13.] [13.7] [14.1] [15.2] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] Code no Weight kg [lb] [15.2] [16.3] [12.1] [12.1] [12.3] [13.] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [12.3] [12.6] [13.] [13.7] [14.1] [14.6] [15.2] [16.3] [13.2] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] 52L262 Rev CF Nov

36 Weight of Motors Weight of Motors Code no Weight Code no Weight kg [lb] kg [lb] [12.3] [12.6] [13.] [13.2] [13.7] [14.1] [14.6] [15.2] [16.3] [11.9] [11.9] [13.4] [13.7] [14.1] [14.3] [14.8] [15.2] [15.7] [16.3] [17.4] [12.1] [12.3] [12.8] [13.] [13.4] [13.9] [14.3] [15.] [16.1] [12.1] [12.3] [12.8] [13.] [13.4] [13.9] [14.3] [15.] [16.1] [12.3] [12.6] [13.] [13.7] [14.1] [15.2] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [16.1] [16.5] [16.8] [17.2] [17.9] [19.] [2.1] [21.2] [22.3] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [2.9] [2.9] [2.7] [2.9] [21.4] [22.1] [23.1] [24.3] [25.4] [26.5] [14.8] Code no Weight kg [lb] [15.2] [16.5] [17.6] [18.7] [2.9] [2.7] [2.9] [21.4] [22.1] [23.1] [24.3] [25.4] [26.5] [32.] [32.4] [33.1] [34.2] [25.4] [26.5] [26.5] [27.6] [27.6] [28.7] [29.8] [3.9] [25.4] [26.5] [26.5] [27.6] [27.6] [28.7] [29.8] [3.9] [11.] [11.2] [11.7] [11.9] [12.3] [12.8] [13.2] [13.9] [15.] [12.3] [12.6] [13.] [11.9] [13.7] [14.1]

37 Weight of Motors Weight of Motors Code no Weight kg [lb] [14.6] [15.2] [16.3] [11.] [11.2] [11.7] [12.3] [12.8] [13.2] [13.9] [15.] [12.] [12.] [12.3] [12.1] [12.3] [12.8] [13.] [13.4] [13.9] [14.3] [15.] [16.1] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [14.8] [15.2] [15.4] [16.5] [17.6] [18.7] [2.9] [13.4] [13.9] [14.1] [14.6] [15.2] [16.3] [17.4] [18.5] [19.6] 151H [23.1] Code no Weight kg [lb] 151H [24.3] 151H [25.4] 151H [27.1] 151H [28.7] 151H [23.1] 151H [24.3] 151H [25.4] 151H [27.1] 151H [28.7] 151H [23.1] 151H [24.3] 151H [25.4] 151H [27.1] 151H [28.7] 151H [25.4] 151H [27.1] 151H [28.7] 151H [23.1] 151H [24.3] 151H [25.4] 151H [27.1] 151H [28.7] 151H [23.1] 151H [24.3] 151H [25.4] 151H [27.1] 151H [28.7] 151H [23.1] 151H [28.7] 151H [24.3] 151H [25.4] 151H [27.1]