IMPORTANTE Antes de de utilizar su su nuevo Switch Kit C fast Ethernet, por favor lea las siguientes recomendaciones No intente desarmar el equipo, puede causar malfuncionamiento y se anulará de la garantía. No exponga el equipo a temperaturas extremas. No use ni almacene este equipo en lugares donde pueda caer agua. Puede causar mal funcionamiento. Siempre utilice un paño suave y seco para limpiar el equipo. ESPAÑOL CARACTERISTICAS Cumple con los estándares IEEE802.3, IEEE802.3u. Velocidad de transmisión de hasta 100Mbps. Puertos RJ45 con auto negociación. Soporta Auto-MDI / MDIX. Soporta control de flujo en modo Full Duplex y Half Duplex. Soporta MAC address, auto aprendizaje y auto envejecimiento LEDs indicadores de monitoreo de encendido, enlace y actividad. ESPAÑOL-02
CONTROLES 1.- Indicador de encendido. Enciende cuando el equipo se conecta a un tomacorriente. 2.- Indicador de actividad / enlace. Enciende cuando un equipo está conectado al puerto RJ45 correspondiente / parpadea cuando hay transmisión o recepción de datos. ESPAÑOL 3.- Conectores RJ45. Permite conectar hasta 8 dispositivos al switch. 4.- Adaptador de corriente. Permite conectar el adaptador de corriente suministrado. ESPAÑOL-03
INSTALACION Decida donde desea colocar el switch. Localice una superfi cie horizontal como un escritorio o mesa. El switch NO incluye tornillos para colocarlo verticalmente. Asegúrese de que el lugar seleccionado: - No le de la luz del sol directamente. - No esté cerca de lugares calientes o aire caliente. - El switch debe tener por lo menos 5 centímetros de espacio libre alrededor. - Que esté bien ventilado. ESPAÑOL Además, requiere un cable categoría 5 (Cat 5) con conectores RJ45 para cada equipo que desee conectar al switch. Cada cable de Ethernet debe ser menor a 100 metros. 1.- Coloque el switch en una superficie plana o en la pared. 2.- Para cada dispositivo, inserte una de las terminales del cable de Ethernet en el puerto del dispositivo que desee utilizar y la otra terminal en uno de los puertos del switch. 3.- Conecte el adaptador de corriente en el switch y el extremo contrario en un tomacorriente casero. La luz indicadora de energía se enciende así como los números de los puertos conectados. Si existe alguna transmisión o recepción de datos, el indicador parpadea. ESPAÑOL-04
Si conecta más de 8 dispositivos al switch, debe instalar un Hub u otro switch a este equipo. Si ninguna luz se enciende, consulte la sección de Problemas y soluciones. Cable Este Kit Ethernet es ideal no incluido para estudiantes en el paquete. o aficionados a la meca- ESPAÑOL ESPAÑOL-05
PROBLEMAS Y SOLUCIONES PROBLEMA El indicador de encendido no se enciende. SOLUCION Asegúrese de que el adaptador de corriente esté conectado al switch. Asegúrese de utilizar el adaptador de corriente suministrado en el empaque. ESPAÑOL El indicador de puerto no enciende aún cuando hay un dispositivo conectado. Asegúrese de que los conectores de los cables están correctamente instalados en el switch y en el dispositivo. Asegúrese de que el dispositivo conectado al switch esté encendido. Revise que el cable sea menor a 100 metros. ESPAÑOL-06
ESPECIFICACIONES Alimentación: 9V - - - 0,6 A Estándares: IEEE802.3 IEEE802.3u Puertos: 5 10/100Mbps puertos auto-negociables Tipo de cable: Cat. 5, Cat. 5e Ethernet para 100Mbps Cat. 3, 4, 5 para 10 Mbps Relación de datos: 10/100Mbps para medio duplex 20/200Mbps para full duplex ESPAÑOL Indicadores LED: Actividad, enlaces y energía. Temperatura de operación: 0 C - 40 C (32 F-104 F) Humedad de operación: 10% - 90% RH no condensada CONVERTIDOR Alimentación: 100-240 V~ Salida: 9V - - - 0,6 A 50/60Hz 0,3 A El diseño del producto y las especificaciones pueden cambiar sin previo aviso. ESPAÑOL-07
Producto: Switch Fast Ethernet 10/100 de 5 puertos Modelo: SWI-005 Marca: Steren PÓLIZA DE GARANTÍA Esta póliza garantiza el producto por el término de un año en todas sus partes y mano de obra, contra cualquier defecto de fabricación y funcionamiento, a partir de la fecha de entrega. CONDICIONES 1.- Para hacer efectiva la garantía, presente ésta póliza y el producto, en donde fue adquirido o en Electrónica Steren S.A. de C.V. 2.- Electrónica Steren S.A de C.V. se compromete a reparar el producto en caso de estar defectuoso sin ningún cargo al consumidor. Los gastos de transportación serán cubiertos por el proveedor. 3.- El tiempo de reparación en ningún caso será mayor a 30 días, contados a partir de la recepción del producto en cualquiera de los sitios donde pueda hacerse efectiva la garantía. 4.- El lugar donde puede adquirir partes, componentes, consumibles y accesorios, así como hacer válida esta garantía es en cualquiera de las direcciones mencionadas posteriormente. ESTA PÓLIZA NO SE HARA EFECTIVA EN LOS SIGUIENTES CASOS: 1.- Cuando el producto ha sido utilizado en condiciones distintas a las normales. 2.- Cuando el producto no ha sido operado de acuerdo con el instructivo de uso. 3.- Cuando el producto ha sido alterado o reparado por personal no autorizado por Electrónica Steren S.A. de C.V. El consumidor podrá solicitar que se haga efectiva la garantía ante la propia casa comercial donde adquirió el producto. Si la presente garantía se extraviara, el consumidor puede recurrir a su proveedor para que le expida otra póliza de garantía, previa presentación de la nota de compra o factura respectiva.
DATOS DEL DISTRIBUIDOR Nombre del Distribuidor Domicilio Producto Marca Modelo Número de serie En caso de que su producto presente alguna falla, acuda al centro de distribución más cercano a su domicilio y en caso de tener alguna duda o pregunta por favor llame a nuestro Centro de Atención a Clientes, en donde con gusto le atenderemos en todo lo relacionado con su producto Steren. Centro de Atención a Clientes 01 800 500 9000 Fecha de entrega ELECTRONICA STEREN S.A. DE C.V. Camarones 112, Obrero Popular, 02840, México, D.F. RFC: EST850628-K51 STEREN PRODUCTO EMPACADO S.A. DE C.V. Biólogo MaximIno Martínez No. 3408 Int. 3 y 4, San Salvador Xochimanca, México, D.F. 02870, RFC: SPE941215H43 ELECTRONICA STEREN DEL CENTRO, S.A. DE C.V. Rep. del Salvador 20 A y B, Centro, 06000, México. D.F. RFC: ESC9610259N4 ELECTRONICA STEREN DE GUADALAJARA, S.A. López Cotilla No. 51, Centro, 44100, Guadalajara, Jal. RFC: ESG810511HT6 ELECTRONICA STEREN DE MONTERREY, S.A. Colón 130 Pte., Centro, 64000, Monterrey, N.L. RFC: ESM830202MF8 ELECTRONICA STEREN DE TIJUANA, S.A. de C.V. Calle 2a, Juárez 7636, Centro, 22000, Tijuana, B.C.N. RFC: EST980909NU5
IMPORTANT Before using your new Fast Ethernet switch, please read the following recommendations. ENGLISH Do not try to open the equipment, may cause malfunction. Warranty is void if you open the case. Do not expose the device to extreme weather. Do not use or store the equipment near wet places. May cause malfunction or shock hazard. Clean with a soft, dry cloth. FEATURES Complies with IEEE802.3, IEEE802.3u standards. Data transfer up to 100Mbps. RJ45 ports with auto negotiation. Supports Auto-MDI /MDIX. Supports Full Duplex flow control and Half Duplex flow control. Supports MAC address, auto learning and auto aging. LEDs indicator for Power, Link and Activity. ENGLISH-02
CONTROLS 1.- Power LED. Light on when the equipment plugs to an AC household outlet. ENGLISH 2.- Link / ACT LED. Light on when the equipment is connected to a RJ45 port / flashes when there s reception or transmission of data. 3.- RJ45 connector. Allows you to plug devices to switch. 4.- AC power adaptor. Allows you to plug the AC power adaptor included in the package. ENGLISH-03
INSTALATION Decide where you want to place the switch. Find a flat horizontal surface such as a table, desk or shelf. The switch DO NOT comes with a wall-mounting screws to place it vertically. ENGLISH Make sure the selected location is: - Not in direct sunlight - Not near a heater or heating vent - Not cluttered or crowded. There should be at least 2 inches of clear space on all sides of the switch. - Well ventilated Also, you ll need a Category 5 (Cat 5) Ethernet cable with RJ45 connectors for each device you want to connect into the switch. Each Ethernet cable must be smaller than 328 feet. 1.- Place the switch on a fl at surface or hook onto the screws (screws not included). 2.- For each device, insert one end of an Ethernet cable into the port in the device and insert the other end into one of the Ethernet ports on the switch. 3.- Connect the power s adapter cord into the switch and then plug the adapter into an AC household outlet. The Power light should light up. The corresponding port number for each connected and powered device should light and fl ash when activity occurs. ENGLISH-04
If you have more than 5 devices which want to connect to the switch, you must do it through a hub or another switch. If any light doesn t operate as we indicated, refers to Troubleshooting section. Ethernet cable is not included in the package. This kit is ideal for electronic students or hobbyists because it allows them to develop creativity in the programming of ENGLISH ENGLISH-05
TROUBLESHOOTING ENGLISH TROUBLE The power light does not lit. SOLUTION Make sure the power cord is properly connected to the switch. Make sure you are using the supplied power adapter. The port number light does not lit for a connected device. Make sure the cable connectors are securely plugged to the switch. Make sure the connected device is turned on. Make sure the cable is smaller than 328 feet. ENGLISH-06
SPECIFICATIONS Input: 9V - - - 0.6 A Standars: IEEE802.3 IEEE802.3u Ports: 5 10/100Mbps auto-negotiation ports Cable type: Cat. 5, Cat. 5e Ethernet for 100Mbps Cat. 3, 4, 5 for 10 Mbps Data rate: 10/100Mbps for half duplex 20/200Mbps for full duplex LEDs: Link, activity, power. Operating temperature: 0 C - 40 C (32 F-104 F) RF: 10% - 90% RH non-condensed ENGLISH AC power adaptor Input: 100-240 V~ 50/60Hz 0.3 A Output: 9V - - - 0.6 A Product design and specifications subject to change without previous notice. ENGLISH-07
Product: 5 Port fast Ethernet switch Part number: SWI-005 Brand: Steren WARRANTY This Steren product is warranted under normal usage against defects in workmanship and materials to the original purchaser for one year from the date of purchase. CONDITIONS 1.- This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be presented when warranty service is required. 2.- If the product stills on the warranty time, the company will repair it free of charge. 3.- The repairing time will not exceed 30 natural days, from the day the claim was received. 4.- Steren sell parts, components, consumables and accessories to customer, as well as warranty service, at any of the addresses mentioned later. THIS WARRANTY IS VOID IN THE NEXT CASES: If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions, improper repair by unauthorized personnel, improper safe keeping, among others. a) The consumer can also claim the warranty service in the purchase establishment. b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.