Wide Range of Hydraulics Motors F 31 245 Wide Range of Hydraulic Motors Sauer-Danfoss is a world leader within production of low speed hydraulic motors with high torque. We can offer more than 3 different hydraulic motors, categorised in types, variants and sizes (incl. different shaft versions). The motors vary in size (rated displacement) from 8 cm3 [.5 in3] to 8 cm3 [48.9 in3] per revolution. Speeds range up to approx. 25 min-1 (rpm) for the smallest type and up to approx 6 min-1 (rpm) for the largest type. Maximum operating torques vary from 13 Nm [115 lbf in] to 2 Nm [24. lbf in] (peak) and maximum outputs are from 2. kw [2. hp] to kw [95 hp]. Characteristic features: Smooth running over the entire speed range Constant operating torque over a wide speed range High starting torque High return pressure without the use of drain line (High pressure shaft seal) High efficiency Long life under extreme operating conditions Robust and compact design High radial and axial bearing capacity For applications in both open and closed loop hydraulic systems Suitable for a wide variety of hydraulics fluids
Wide Range of Hydraulics Motors The programme is characterised by technical features appealing to a large number of applications and a part of the programme is characterised by motors that can be adapted to a given application. daptions comprise the following variants among others: Motors with corrosion resistant parts Wheel motors with recessed mounting flange OMP, OMR- motors with needle bearing OMR motor in low leakage version OMR motors in a super low leakage version Short motors without bearings Ultra short motors Motors with integrated positive holding brake Motors with integrated negative holding brake Motors with integrated flushing valve Motors with speed sensor Motors with tacho connection ll motors are available with black finish paint The Sauer Danfoss LSHT motors are used in the following application areas: Construction equipment gricultural equipment Material handling & Lifting equipment Forestry equipment Lawn and turf equipment Special purpose Machine tools and stationary equipment Marine equipment Survey of Literature with Technical Data on Sauer-Danfoss Hydraulic Motors Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is divided into 8 individual subcatalogues: General information on Sauer-Danfoss hydraulic motors: function, use, selection of hydraulic motor, hydraulic systems, etc. Technical data on small motors: OML and OMM Technical data on medium sized motors: OMP, OMR and OMH Technical data on medium sized motors: DH and DS Technical data on medium sized motors: OMEW Technical data on large motors: OMS, OMT and OMV Technical data on large motors: TMK Technical data on large motors: TMT Technical data on large motors: TMVW general survey brochure on Sauer-Danfoss hydraulic motors gives a quick motor reference based on power, torque, speed and capabilities.
Version Versions Mounting flange Spigot diam,eter (front /rear end) Bolt circle diameter (BC) Shaft Port size European version US version Side port version End port version Flange port version Standard shaft seal High pressure shaft seal Drain connection Check valve Main type designation Cyl. 32 mm G ½ l l l Yes Yes OMH Cyl. 35 mm G ½ l l l Yes Yes OMH Cyl. 1 1 /4 in /8-14 UNF l l l Yes Yes OMH 4 hole oval flange (4-flange) 82.5 mm [3.25 in] 16.4 mm [4.2 in] Splined 1in SE 6B Splined 1 1 /4 in /8-14 UNF l l l Yes Yes OMH G ½ l l l Yes Yes OMH Splined 1 1 /4 in /8-14 UNF l l l Yes Yes OMH Tapered 35 mm G ½ l l l Yes Yes OMH Functions diagram - see page:
Code Numbers Code Numbers Displacement [cm 3 ] Code numbers 2 25 315 4 5 Technical data - Page Dimensions - Page 151H 12 13 14 15 16 9 91 151H 112 113 114 115 116 8 91 151H 142 143 144 145 146 9 92 151H 18 182 183 184 181 8 92 151H 122 123 124 125 126 8 91 151H 152 153 154 155 156 8 92 151H - - 134 135 136 8 91 84 84 85 85 86 Ordering dd the four digit prefix 151H to the four digit numbers from the chart for complete code number. Example: 151H144 for an OMH 315 with 4 flange, cyl. 1 ¼ in shaft, port size /8-14 UNF Orders will not be accepted without the four digit prefix.
Technical Data Technical data for OMH with 1 in SE 6 B splined shaft Type OMH OMH OMH OMH OMH Motor size 2 25 315 4 5 Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque cm 3 [inch] 21.3 [12.32] 252. [15.42] 314.9 [19.2] 396.8 [24.28] 4.6 [28.8] min -1 3 295 235 185 155 [rpm] int 1) 445 35 285 225 1 N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] bar [psi] at max. press drop N m [lbf in] at max. press.drop int. 1) N m [lbf in] 34 [3] 51 int. 1) [45] 61 peak 2) [54] 11.2 [15.] 1.2 int. 1) [23.] 115 [165] 1 int 1) [25] 215 peak 2) [312] int. 1) 255 [225] 3 [345] 34 [3] 51 [45] 61 [54].5 [1.] 11.9 [16.] [13] 145 [21] 1 [254] 2 [24] 435 [385] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 34 [3] 54 [48] 61 [54] 5.2 [.] 9. [13.] [11] 12 [1] 145 [21] 28 [25] 45 [4] 34 [3] 54 [48] 61 [54] 4.8 [6.5] 8.2 [11.] 6 [] 95 [14] 11 [16] 2 [255] 45 [4] 34 [3] 52 [46] 61 [54] 3. [5.] 6. [8.] 5 [25] [11] [13] 3 [265] 45 [4]
Technical Data Technical data for OMH with 32 mm and 1 1/4 in cylindrical shaft Type OMH OMH OMH OMH OMH Motor size 2 25 315 4 5 Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque cm 3 [inch] 21.3 [12.32] 252. [15.42] 314.9 [19.2] 396.8 [24.28] 4.6 [28.8] min -1 3 295 235 185 155 [rpm] int 1) 445 35 285 225 1 N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] bar [psi] at max. press drop N m [lbf in] at max. press.drop int. 1) N m [lbf in] 51 [45] 58 int. 1) [513] 64 peak 2) [566] 16. [21.5] 18.5 int. 1) [24.8] 1 [254] 2 int 1) [2] 225 peak 2) [326] int. 1) 3 [345] 45 [398] 61 [54} [62] [69] 16. [21.5] 18.5 [24.8] 1 [254] 2 [2] 225 [326] 52 [46] 5 [522] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 5 [522] 6 [593] 84 [44] 12.5 [16.8] 14. [18.8] 135 [196] 155 [225] 1 [26] 51 [451] 5 [522] 5 [522] [62] 84 [44] 1. [13.4] 12. [16.1] 15 [152] 125 [181] 155 [225] 4 [434] 6 [531] 58 [513] 68 [62] 84 [44] 8.5 [11.4] 1. [13.4] 85 [123] 1 [145] 13 [18] 4 [434] 6 [531]
Technical Data Technical data for OMH with 35 mm cylindrical, 1 1/4 in splined and 35 mm tapered shaft Type OMH OMH OMH OMH OMH Motor size 2 25 315 4 5 Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min starting torque cm 3 [inch] 21.3 [12.32] 252. [15.42] 314.9 [19.2] 396.8 [24.28] 4.6 [28.8] min -1 3 295 235 185 155 [rpm] int 1) 445 35 285 225 1 N m [lbf in] kw [hp] bar [psi] l/min [US gal/min] bar [psi] at max. press drop N m [lbf in] at max. press.drop int. 1) N m [lbf in] 51 [45] 58 int. 1) [513] 64 peak 2) [566] 16. [21.5] 18.5 int. 1) [24.8] 1 [254] 2 int 1) [2] 225 peak 2) [326] int. 1) 3 [345] 45 [398] 61 [54} [62] [69] 16. [21.5] 18.5 [24.8] 1 [254] 2 [2] 225 [326] 52 [46] 5 [522] 4 [655] 82 [26] 98 [86] 14. [18.8] 15.5 [2.8 1 [254] 2 [2] 225 [326] 66 [584] 3 [646] 84 [44] 98 [86] 1 [965] 12.5 [16.8] 15. [2.1] 155 [225] 1 [26] 21 [35] 2 [63] 88 [] 82 [26] 14 [921] 11 [136] 11. [14.8] 14. [18.8] 125 [181] 16 [232] 18 [261] 2 [63] 88 [] Type OMH 2-5 bar [psi] bar [psi] bar [psi] cont int. 1) peak 2) Max. inlet pressure 2 [2] 225 [326] 25 [363] Max.return pressure with drain line 1 [254] 2 [2] 225 [326] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute.
Technical Data Max. Permissible Shaft Seal Pressure OMH with standard shaft seal, check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line 151-32.1 OMH with standard shaft seal, check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. Max. return pressure without drain line or max. pressure in the drain line psi 14 bar 1 12 1 int.operation 1) 8 6 5 4 25 2 1 2 3 4 min -1 (rpm) 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 151-1565.1
Technical Data Pressure Drop in Motor p p psi 25 2 15 1 5 bar 18 16 14 12 1 8 6 4 2 Q 1 2 3 4 5 6 8 l/min Q 2 4 6 8 1 12 14 16 18 2 22 24 US gal/min 151-1331.1 The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm 2 /s [165 SUS] Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [-15 psi]. Pressure drop bar [psi] 1 [145] 14 [23] Viscosity mm2/s [SUS] 2 35 [165] 2 35 [165] Oil flow in drain line l/min [US gal/min] 2.5 [.66] 1.8 [.8] 3.5 [.93] 2.8 [.4] Direction of Shaft Rotation 151-21.1
Technical Data Permissible Shaft Loads for OMH The permissible shaft load (P rad ) is calculated from the speed (n) and the distance (l) between the point of load application and the mounting flange. P rad = 11 n 25 13.5 + l N*; l in mm P rad = 11 n 2215 4. + l lbf*; l in inch *n > 2 min -1 (rpm); l < 6 mm [2.36 in] n < 2 min -1 (rpm); => P Rmax = 11 N [24 lbf] P rad. lbf P rad. N 3 P rad. 25 2 15 12 1 8 6 6 lbf 3 N 1 5 4 2 3 N 6 lbf 1 2 3 4 3 [1.18] 151-144.1 --------- 1 in SE 6B splined shaft The drawing shows the permissible radial load when l = 3 mm [1.18 in].
Function Diagrams Function Diagrams lbf in 55 5 Nm 6 OMH 2 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] l/min [18.5US gal/min] l/min [19.8 US gal/min] 8 l/min [21.1 US gal/min] Q= l/min [23.8 US gal/min] 45 4 35 3 25 2 15 1 5 4 3 2 1 N=1kW 1hp 4hp 2kW 2hp 4kW η t =8% 8kW 8hp 85% 8% 12kW 16hp 12hp N= 2hp N= 2kW 16kW p=2 bar 2 psi 1 bar 254 psi 14 bar 23 psi 15 bar 152 psi bar 12 psi 5 % η t =6% p= 35 bar 51 psi 5 1 15 2 25 3 35 4 45 min -1 (rpm) lbf in Nm 8 OMH 25 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] l/min [18.5US gal/min] l/min [19.8 US gal/min] 8 l/min [21.1 US gal/min] Q= l/min [23.8 US gal/min] 151-1486.1 6 5 4 3 2 1 6 5 4 3 2 1 N=1kW 1hp 2kW 2hp 8hp 4kW 4hp 6kW 6hp η t =85% 14hp 12hp % η t =6% 8kW 1hp 8% 12kW N= 16hp 1kW N= 16kW 14kW p=2 bar 2 psi 1 bar 254 psi 145 bar 21 psi 12 bar 14 psi bar 13 psi bar 12 psi p= 35 bar 51 psi 25 5 1 125 15 1 2 225 25 2 3 325 35 3 4 min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page. Continuous range 151-148.1 Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page 8-8. Intermittent pressure drop and oil flow must not occur simultaneously.
Function Diagrams Function Diagrams lbf in Nm OMH 315 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] l/min [18.5US gal/min] l/min [19.8 US gal/min] 8 l/min [21.1 US gal/min] Q= l/min [23.8 US gal/min] 8 6 5 4 3 2 1 6 5 4 3 2 1 N=1kW 1hp 6hp 4kW 2kW 4hp 2hp 1hp 6kW 8hp η t =85% 12hp 8kW 8% % η t =6% 14hp 1kW N= 16kW 14kW 12kW 16hp p=2 bar 2 psi 1 bar 254 psi 155 bar 225 psi 135 bar 196 psi 1 bar 145 psi bar 1 psi p= 35 bar 51 psi 25 5 1 125 15 1 2 225 25 2 3 325 min -1 (rpm) 151-1488.1 lbf in Nm OMH 4 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] l/min [18.5US gal/min] l/min [19.8 US gal/min] 8 l/min [21.1 US gal/min] Q= l/min [23.8 US gal/min] 1 8 6 5 4 3 2 1 8 6 4 2 N=1kW 1hp 4hp 2kW 2hp 4kW η t =85% 6kW 6hp 8% % η t =6% 14hp 1kW 12hp 8kW 8hp 8kW 1hp N= 14kW 12kW p=1 bar 26 psi 155 bar 225 psi 125 bar 181 psi 15 bar 152 psi 6 bar 8 psi p= 35 bar 51 psi 25 5 1 125 15 1 2 225 25 2 min -1 (rpm) 151-1489.1 Explanation of function diagram use, basis and conditions can be found on page. Continuous range Intermittent range (max. 1% operation every minute)max. permissible continuous/ intermittent pressure drop for the actual shaft version can be found on page 8-8. Intermittent pressure drop and oil flow must not occur simultaneously.
Function Diagrams Function Diagrams lbf in 55 5 Nm 6 OMH 2 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] l/min [18.5US gal/min] l/min [19.8 US gal/min] 8 l/min [21.1 US gal/min] Q= l/min [23.8 US gal/min] 45 4 35 3 25 2 15 1 5 4 3 2 1 N=1kW 1hp 4hp 2kW 2hp 4kW η t =8% 8kW 8hp 85% 8% 12kW 16hp 12hp N= 2hp N= 2kW 16kW p=2 bar 2 psi 1 bar 254 psi 14 bar 23 psi 15 bar 152 psi bar 12 psi 5 % η t =6% p= 35 bar 51 psi 5 1 15 2 25 3 35 4 45 min -1 (rpm) 151-1486.1 Explanation of function diagram use, basis and conditions can be found on page. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent pressure drop for the actual shaft version can be found on page 8-8. Intermittent pressure drop and oil flow must not occur simultaneously.
Shaft Version Shaft Version 56.8 [2.236] 55.2 [2.13] 45 R.5 [.2] min. 18 [.1] max. 6 [.24] - : Cylindrical shaft 32 mm D: Parallel key 1 8 45 DIN 6885 Ø36 [1.42] 45. [1.2] 44. [1.6] M8 Ø32.18 [1.261] Ø32.2 [1.26] 5.5 [.21] 4.5 [.1] 35. [1.38] 34. [1.366] 1. [.394] 9.964 [.392] D B: Cylindrical shaft 35 mm E: Parallel key 1 8 45 DIN 6885 B Ø36 [1.42] 45 56.8 [2.236] 55.2 [2.13] R.4 [.16] M8 min. 18 [.1] max. 6 [.24] Ø35.18 [1.39] Ø35.2 [1.38] 38. [1.496] 3.1 [1.461] - 45. [1.2] 44. [1.6] 5.5 [.21] 4.5 [.1] 1. [.394] 9.964 [.392] E 46. [1.839] 45.1 [1.6] min. 26.5 [1.43] US version C: Cylindrical shaft 1 1 /4 in F: Parallel key 5 /16 5 /16 1 1 /4 in SE J 44 C Ø36 [1.42] 45 R.4 [.16] Ø31. [1.25] Ø31.3 [1.249] max. [.28] 3/8-16UNC 35.33 [1.391 33.5 [1.38] - F 31. [1.25] 31.3 [1.235] 4.5 [.1] 3.5 [.138].96 [.31].94 [.313] 151-1852.11
Shaft Version Shaft Version 4.8 [1.66] 39.2 [1.543] min. 14 [.55] D: Splined shaft SE 6 B (B.S. 259) Straight-sided, bottom fitting, deep. Fit 2 Nom. size 1 in D Ø28.56 [1.124] 45 R.5 [.2] max. 6 [.24] ¼ -2UNC Ø25.348 [.998] Ø25.298 [.996] 6.2 [.24] 6.21 [.244] - *21.54 [.848] *21.4 [.843] *Deviates from SE 6 B (B.S. 259) R max. 35.5 [1.398] 25.4 [1.] 24.4 [.961] 6x6 56. [2.232] 55.1 [2.169] E. Involute splined shaft NS B92.1-198 standard Flat root side fit Pitch 12/24 Teeth 14 Major dia. 1.25 in Pressure angle 3 E Ø36 [1.42] 45 R.4 [.16] 38 [1.5] 36 [1.42] min. 18 [.1] max. 6 [.24] M8 Ø31. [1.41] Ø31.25 [1.249] - 151-1853.11
Shaft Version Shaft Version 46. [1.839] 45.1 [1.6] US version F. Involute splined shaft NS B92.1-19 standard Flat root side fit Pitch 12/24 Teeth 14 Major dia. 1.25 in Pressure angle 3 F Ø36 [1.42] 45 R.4 [.16] Ø31. [1.25] Ø31.2 [1.249] min. 26.5 [1.43] max. [.28] 3/8-16UNC - 34.5 [1.358] 32. [1.26] G: Tapered shaft 35 mm I: DIN 93 NV 41 Tightening torque: 2 ± 1 Nm [1 ±85 lbf in] H: Taper 1:1 L: Parallel key B6 6 2 DIN 6885 G Ø36 [1.42] H I Ø4.5 [.1] M2x1.5 [.59] ø44 [1.3] 19.1 [.2] 18.9 [.44] - 2 [.9] 6 [.24] 5.9 [.235] 13 [.51] 36 [1.42] 4 [.16] 58.4 [2.299] 5.6 [2.268] L 151-1854.11
Technical Data Port Thread Versions B min. 15 [.59] max. ø21.5 [.846] ø3.5 [1.2] ø29.5 [1.161] E F 1. [.4] min. 16. [.65] : G main ports B: UNF main ports E: ISO 228/1 - G 1 /2 F: /8-14 UNF O-ring boss port C G 12.2 [.43] 11.8 [.465] max..6 [.24] D ø18.5 [.28] ø1.5 [.689] H min. 12 [.4] 151-1858.1 C: G drain port D: UNF drain port G: ISO 228/1 - G 1 /4 H: /16-2 UNF O-ring boss port Manifold Mount European version 36 [1.42] L 2 [.9] 2 [.9] 2 [.9] 2 [.9] L: see dimensional drawing for given OMH motor on pages 91-92 18 [.1] 18 [.1] 151-2135.1
Dimensions-European Version Dimensions Side port version with 4 hole oval mounting flange (4-flange). Type OMH 2 OMH 25 OMH 315 OMH 4 OMH 5 Max. L mm [in] 11.1 [6.4] 18.1 [.1] 186.8 [.35] 198.1 [.8] 28.3 [8.2] L 1 mm [in] 2.8 [1.9] 34.8 [1.3] 43.5 [1.1] 54.8 [2.16] 65. [2.56] C: Drain connection G ¼; 12 mm [.4 in] deep D: G ½; 15 mm [.59 in] deep M8 D M8 L 36 [1.42] 46.4 [1.82] max. 68 [2.68] Ø82.55 [3.25] Ø82.45 [3.246] Ø13.5 [.53] 6.1 [.24] 16 [.63] C 18 [.1] max. Ø121 [4.6] 18 [.1] 16.4 [4.189] 62 [2.44] max. 135 [5.31] L 1 45º max. 123.5 [4.862] 151-1324.11
Dimensions-US Version Dimensions Side port version with 4 hole oval mounting flange (4 flange). Output shaft.max. Splined shaft 1 in Other shaft versions mm L 2 [in] 5.5 [1.99] 58. [2.28] Type OMH 2 OMH 25 OMH 315 OMH 4 OMH 5 Max. L mm [in] 11.1 [6.4] 18.1 [.1] 186.8 [.35] 198.1 [.8] 28.3 [8.2] L 1 mm [in] 2.8 [1.9] 34.8 [1.3] 43.5 [1.1] 54.8 [2.16] 65. [2.56] C: Drain connection 16-2 UNF; 12 mm [.4 in] deep D: 8-14 UNF; 15 mm [.59 in] deep
Weight of Motors Weight of Motors Code no Weight kg [lb] 151-28.2 [15.9] 151-242 6.9 [15.2] 151-243. [15.4] 151-244.5 [16.5] 151-245 8. [1.6] 151-246 9. 151-24 8.5 [18.] 151-248 6. [14.8] 151-265 6. [14.8] 151-266 6.9 [15.2] 151-26. [15.4] 151-268.5 [16.5] 151-269 8. [1.6] 151-2 9. 151-21 8.5 [18.] 151-3 5.6 [12.3] 151-31 5. [12.6] 151-32 5.9 [13.] 151-33 6. [13.2] 151-34 6.2 [13.] 151-35 6.4 [14.1] 151-36 6.6 [14.6] 151-3 6.9 [15.2] 151-38.4 [16.3] 151-31 5.6 [12.3] 151-311 5. [12.6] 151-312 5.9 [13.] 151-313 6. [13.2] 151-314 6.2 [13.] 151-315 6.4 [14.1] 151-316 6.6 [14.6] 151-31 6.9 [15.2] 151-318.4 [16.3] 151-319 5.6 [12.3] 151-33 5.6 [12.3] 151-331 5. [12.6] 151-332 5.9 [13.] 151-333 6. [13.2] 151-334 6.2 [13.] 151-335 6.4 [14.1] 151-336 6.6 [14.6] 151-33 6.9 [15.2] 151-338.4 [16.3] 151-34 5.5 [12.1] 151-341 5.5 [12.1] 151-342 5.6 [12.3] 151-4 6. [14.8] 151-41 6.9 [15.2] 151-42. [15.4] 151-43.2 [15.9] 151-44.5 [16.5] Code no Weight kg [lb] 151-45 8. [1.6] 151-46 8.5 [18.] 151-4 9. 151-48 9.5 [2.9] 151-41 6. [14.8] 151-411 6.9 [15.2] 151-412. [15.4] 151-413.2 [15.9] 151-414.5 [16.5] 151-415 8. [1.6] 151-416 8.5 [18.] 151-41 9. 151-418 9.5 [2.9] 151-42 6. [14.8] 151-421 6.9 [15.2] 151-422. [15.4] 151-423.2 [15.9] 151-424.5 [16.5] 151-425 8. [1.6] 151-426 8.5 [18.] 151-42 9. 151-428 9.5 [2.9] 151-6 5.6 [12.3] 151-61 5. [12.6] 151-62 5.9 [13.] 151-63 6. [13.2] 151-64 6.2 [13.] 151-65 6.4 [14.1] 151-66 6.6 [14.6] 151-6 6.9 [15.2] 151-68.4 [16.3] 151-61 5.6 [12.3] 151-611 5. [12.6] 151-612 5.9 [13.] 151-613 6. [13.2] 151-614 6.2 [13.] 151-615 6.4 [14.1] 151-616 6.6 [14.6] 151-61 6.9 [15.2] 151-618.4 [16.3] 151-622 5.9 [13.] 151-624 6.2 [13.] 151-625 6.4 [14.1] 151-62 6.9 [15.2] 151-63 5.6 [12.3] 151-631 5. [12.6] 151-632 5.9 [13.] 151-633 6. [13.2] 151-634 6.2 [13.] 151-635 6.4 [14.1] 151-636 6.6 [14.6] Code no Weight kg [lb] 151-63 6.9 [15.2] 151-638.4 [16.3] 151-64 5.5 [12.1] 151-641 5.5 [12.1] 151-642 5.6 [12.3] 151-646 5.9 [13.] 151-6. [14.8] 151-1 6.9 [15.2] 151-2. [15.4] 151-3.2 [15.9] 151-4.5 [16.5] 151-5 8. [1.6] 151-6 8.5 [18.] 151-9. 151-8 9.5 [2.9] 151-1 6. [14.8] 151-11 6.9 [15.2] 151-12. [15.4] 151-13.2 [15.9] 151-14.5 [16.5] 151-15 8. [1.6] 151-16 8.5 [18.] 151-1 9. 151-18 9.5 [2.9] 151-2 6. [14.8] 151-21 6.9 [15.2] 151-22. [15.4] 151-23.2 [15.9] 151-24.5 [16.5] 151-25 8. [1.6] 151-26 8.5 [18.] 151-2 9. 151-28 9.5 [2.9] 151-128 5.6 [12.3] 151-129 5. [12.6] 151-121 5.9 [13.] 151-1211 6.2 [13.] 151-1212 6.4 [14.1] 151-1213 6.6 [14.6] 151-1214 6.9 [15.2] 151-1215.4 [16.3] 151-121 6. [13.2] 151-1231 6. [14.8] 151-1232 6.9 [15.2] 151-1233. [15.4] 151-1234.5 [16.5] 151-1235 8. [1.6] 151-1236 8.5 [18.] 151-123 9. 151-1238.2 [15.9] 151-1243 9.5 [2.9]
Weight of Motors Weight of Motors Code no Weight Code no Weight kg [lb] kg [lb] 151-51 5.6 [12.3] 151-52 5. [12.6] 151-53 5.9 [13.] 151-54 6. [13.2] 151-55 6.2 [13.] 151-56 6.4 [14.1] 151-5 6.6 [14.6] 151-58 6.9 [15.2] 151-59.4 [16.3] 151-51 5.4 [11.9] 151-514 5.4 [11.9] 151-5191 6.1 [13.4] 151-5192 6.2 [13.] 151-5193 6.4 [14.1] 151-5194 6.5 [14.3] 151-5195 6. [14.8] 151-5196 6.9 [15.2] 151-519.1 [15.] 151-5198.4 [16.3] 151-5199.9 [1.4] 151-5211 5.5 [12.1] 151-5212 5.6 [12.3] 151-5213 5.8 [12.8] 151-5214 5.9 [13.] 151-5215 6.1 [13.4] 151-5216 6.3 [13.9] 151-521 6.5 [14.3] 151-5218 6.8 [15.] 151-5219.3 [16.1] 151-531 5.5 [12.1] 151-532 5.6 [12.3] 151-533 5.8 [12.8] 151-534 5.9 [13.] 151-535 6.1 [13.4] 151-536 6.3 [13.9] 151-53 6.5 [14.3] 151-538 6.8 [15.] 151-539.3 [16.1] 151-5311 5.6 [12.3] 151-5312 5. [12.6] 151-5313 5.9 [13.] 151-5315 6.2 [13.] 151-5316 6.4 [14.1] 151-5318 6.9 [15.2] 151-6 6. [14.8] 151-61 6.9 [15.2] 151-62. [15.4] 151-63.2 [15.9] 151-64.5 [16.5] 151-65 8. [1.6] 151-66 8.5 [18.] 151-6 9. 151-68 9.5 [2.9] 151-61 6. [14.8] 151-611 6.9 [15.2] 151-612. [15.4] 151-613.2 [15.9] 151-614.5 [16.5] 151-615 8. [1.6] 151-616 8.5 [18.] 151-61 9. 151-618 9.5 [2.9] 151-611 6. [14.8] 151-6111 6.9 [15.2] 151-6112. [15.4] 151-6113.2 [15.9] 151-6114.5 [16.5] 151-6115 8. [1.6] 151-6116 8.5 [18.] 151-611 9. 151-6118 9.5 [2.9] 151-61.3 [16.1] 151-6191.5 [16.5] 151-6192.6 [16.8] 151-6193.8 [1.2] 151-6194 8.1 [1.9] 151-6195 8.6 [19.] 151-6196 9.1 [2.1] 151-619 9.6 [21.2] 151-6198 1.1 [22.3] 151-621 6. [14.8] 151-6211 6.9 [15.2] 151-6212. [15.4] 151-6213.2 [15.9] 151-6214.5 [16.5] 151-6215 8. [1.6] 151-6216 8.5 [18.] 151-621 9. 151-6218 9.5 [2.9] 151-6294 9.5 [2.9] 151-6295.2 [15.9] 151-6296 9.5 [2.9] 151-63 9. 151-631 9.4 [2.] 151-632 9.5 [2.9] 151-633 9. [21.4] 151-634 1. [22.1] 151-635 1.5 [23.1] 151-636 11. [24.3] 151-63 11.5 [25.4] 151-638 12. [26.5] 151-638 6. [14.8] Code no Weight kg [lb] 151-6381 6.9 [15.2] 151-6383.2 [15.9] 151-6384.5 [16.5] 151-6385 8. [1.6] 151-6386 8.5 [18.] 151-638 9. 151-6388 9.5 [2.9] 151-643 9. 151-6431 9.4 [2.] 151-6432 9.5 [2.9] 151-6433 9. [21.4] 151-6434 1. [22.1] 151-6435 1.5 [23.1] 151-6436 11. [24.3] 151-643 11.5 [25.4] 151-6438 12. [26.5] 151-6442 14.5 [32.] 151-6443 14. [32.4] 151-6444 15. [33.1] 151-6445 15.5 [34.2] 151-6461 11.5 [25.4] 151-6462 12. [26.5] 151-6463 12. [26.5] 151-6464 12.5 [2.6] 151-6465 12.5 [2.6] 151-6466 13. [28.] 151-646 13.5 [29.8] 151-6468 14. [3.9] 151-641 11.5 [25.4] 151-642 12. [26.5] 151-643 12. [26.5] 151-644 12.5 [2.6] 151-64 12.5 [2.6] 151-646 13. [28.] 151-64 13.5 [29.8] 151-648 14. [3.9] 151-21 5. [11.] 151-22 5.1 [11.2] 151-23 5.3 [11.] 151-24 5.4 [11.9] 151-25 5.6 [12.3] 151-26 5.8 [12.8] 151-2 6. [13.2] 151-28 6.3 [13.9] 151-29 6.8 [15.] 151-41 5.6 [12.3] 151-42 5. [12.6] 151-43 5.9 [13.] 151-44 5.4 [11.9] 151-45 6.2 [13.] 151-46 6.4 [14.1]
Weight of Motors Weight of Motors Code no Weight kg [lb] 151-4 6.6 [14.6] 151-48 6.9 [15.2] 151-49.4 [16.3] 151-61 5. [11.] 151-62 5.1 [11.2] 151-63 5.3 [11.] 151-65 5.6 [12.3] 151-66 5.8 [12.8] 151-6 6. [13.2] 151-68 6.3 [13.9] 151-69 6.8 [15.] 151-8 5.4 [12.] 151-81 5.4 [12.] 151-82 5.6 [12.3] 151-11 5.5 [12.1] 151-12 5.6 [12.3] 151-13 5.8 [12.8] 151-14 5.9 [13.] 151-15 6.1 [13.4] 151-16 6.3 [13.9] 151-1 6.5 [14.3] 151-18 6.8 [15.] 151-19.3 [16.1] 151-24 6. [14.8] 151-241 6.9 [15.2] 151-242. [15.4] 151-243.2 [15.9] 151-244.5 [16.5] 151-245 8. [1.6] 151-246 8.5 [18.] 151-24 9. 151-248 9.5 [2.9] 151-25 6. [14.8] 151-251 6.9 [15.2] 151-252. [15.4] 151-253.2 [15.9] 151-254.5 [16.5] 151-255 8. [1.6] 151-256 8.5 [18.] 151-25 9. 151-258 9.5 [2.9] 151-26 6.1 [13.4] 151-261 6.3 [13.9] 151-262 6.4 [14.1] 151-263 6.6 [14.6] 151-264 6.9 [15.2] 151-265.4 [16.3] 151-266.9 [1.4] 151-26 8.4 [18.5] 151-269 8.9 [19.6] 151H12 1.5 [23.1] Code no Weight kg [lb] 151H13 11. [24.3] 151H14 11.5 [25.4] 151H15 12.3 [2.1] 151H16 13. [28.] 151H112 1.5 [23.1] 151H113 11. [24.3] 151H114 11.5 [25.4] 151H115 12.3 [2.1] 151H116 13. [28.] 151H122 1.5 [23.1] 151H123 11. [24.3] 151H124 11.5 [25.4] 151H125 12.3 [2.1] 151H126 13. [28.] 151H134 11.5 [25.4] 151H135 12.3 [2.1] 151H136 13. [28.] 151H142 1.5 [23.1] 151H143 11. [24.3] 151H144 11.5 [25.4] 151H145 12.3 [2.1] 151H146 13. [28.] 151H152 1.5 [23.1] 151H153 11. [24.3] 151H154 11.5 [25.4] 151H155 12.3 [2.1] 151H156 13. [28.] 151H18 1.5 [23.1] 151H181 13. [28.] 151H182 11. [24.3] 151H183 11.5 [25.4] 151H184 12.3 [2.1]