Network CD Player OWNER S MANUAL MANUAL DE INSTRUCCIONES

Transcripción

1 RL Network CD Plaer OWNER S MANUAL MANUAL DE INSTRUCCIONES

2 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual carefull. Keep it in a safe place for future reference. 2 Install this sound sstem in a well ventilated, cool, dr, clean place - awa from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top: 10 cm (4 in) Rear: 10 cm (4 in) Sides: 10 cm (4 in) 3 Locate this unit awa from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidit (i.e. a room with a humidifier) to prevent condensation inside this unit, which ma cause an electrical shock, fire, damage to this unit, and/or personal injur. 5 Avoid installing this unit where foreign object ma fall onto this unit and/or this unit ma be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as the ma cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as the ma cause fire, damage to this unit, and/or personal injur. Containers with liquid in them, as the ma fall and liquid ma cause electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it ma cause fire, damage to this unit, and/or personal injur. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It ma overheat, possibl causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dr cloth. 12 Onl voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and ma cause fire, damage to this unit, and/or personal injur. Yamaha will not be held responsible for an damage resulting from use of this unit with a voltage other than specified. 13 To prevent damage b lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or this unit during a lightning storm. 14 Do not attempt to modif or fix this unit. Contact qualified Yamaha service personnel when an service is needed. The cabinet should never be opened for an reasons. 15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. 16 Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is fault. 17 Before moving this unit, press to set this unit to the standb mode, and disconnect the AC power plug from the wall outlet. 18 Condensation will form when the surrounding temperature changes suddenl. Disconnect the power cable from the outlet, then leave this unit alone. 19 When using this unit for a long time, this unit ma become warm. Turn the power off, then leave this unit alone for cooling. 20 Install this unit near the AC outlet and where the AC power plug can be reached easil. 21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Keep the batteries in a location out of reach of children. Batteries can be dangerous if a child were to put in his or her mouth. If the batteries grow old, the effective operation range of the remote control decreases considerabl. If this happens, replace the batteries with two new ones as soon as possible. Do not use old batteries together with new ones. Do not use different tpes of batteries (such as alkaline and manganese batteries) together. Read the packaging carefull as these different tpes of batteries ma have the same shape and color. Exhausted batteries ma leak. If the batteries have leaked, dispose of them immediatel. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the batter compartment thoroughl before installing new batteries. If ou plan not to use the unit for a long period of time, remove the batteries from the unit. Otherwise, the batteries will wear out, possibl resulting in a leakage of batter liquid that ma damage the unit. Do not throw awa batteries with general house waste. Dispose of them correctl in accordance with our local regulations. 22 Excessive sound pressure from earphones and headphones can cause hearing loss. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off b. This state is called the standb mode. In this state, this unit is designed to consume a ver small quantit of power. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. i En

3 CONTENTS PREPARATION WHAT YOU CAN DO WITH THIS UNIT... 2 Sources that can be plaed back on this unit... 2 Devices that can control this unit... 3 Operations from our mobile device... 3 SUPPLIED ACCESSORIES... 4 REMOTE CONTROL PREPARATION... 4 CONTROLS AND FUNCTIONS... 5 Front panel... 5 Remote control... 6 Rear panel... 8 Front panel displa... 8 CONNECTIONS... 9 Connecting to an amplifier... 9 Connecting to a network (PC/NAS/Internet connection) Turning on this unit OPERATIONS SETUP OF YOUR NETWORK DEVICES Sharing music files stored on our PC PLAYBACK OF CDS Plaing back a CD Using A-B repeat plaback Using program plaback mode PLAYBACK OF SPOTIFY SERVICE PLAYBACK OF MUSIC FILES ON YOUR PC/NAS Operations from the main unit or remote control PLAYBACK OF INTERNET RADIO PLAYBACK OF AirPla Plaing ipod Plaing itunes Clearing AirPla SETUP MENU Setup menu operations Setup menu items Advanced setup menu Updating the firmware OTHERS FREQUENTLY ASKED QUESTIONS...26 TROUBLESHOOTING...27 Front panel displa messages ADDITIONAL INFORMATION...32 PLAYABLE DISCS AND FILE FORMATS...33 Plaable media and devices Plaable discs and file formats SPECIFICATIONS...35 (at the end of this manual) Information about third part software licenses...i PREPARATION OPERATIONS OTHERS About this manual Notes contain important information about safet and operating instructions. indicates a tip for our operation. ipod described in this manual ma also refer to iphone or ipad. English 1 En

4 SOURCE PURE DIRECT SELECT PUSH PREPARATION WHAT YOU CAN DO WITH THIS UNIT This unit is a network CD plaer, on which ou can enjo plaing back music files stored on our media server (PC or NAS), audio contents on the Internet radio, CD, Spotif, AirPla devices (ipod/itunes), b connecting the unit to our home network (DLNA) and audio sstem on the same network. For details on DLNA or NAS, see ADDITIONAL INFORMATION ( P.32). Sources that can be plaed back on this unit 1 Internet Amplifier 6 CD Modem 2 PC Broadband router* This unit (CD-N301) 3 NAS 4 ipod (AirPla)* 5 ipod/android (Spotif)* * You need a commerciall available Wi-Fi broadband router when ou use an ipod/android. 1 Pla back the Internet radio ( P.20) 2 Pla back music files stored on our PC ( P.12, 18) 3 Pla back music files stored on our NAS ( P.12, 18) 4 Pla back our ipod with AirPla ( P.22) For details on connecting the devices, see CONNECTIONS ( P.9). 5 Pla back the Spotif service ( P.17) 6 Pla back a CD ( P.14) 2 En

5 SOURCE PURE DIRECT SELECT PUSH WHAT YOU CAN DO WITH THIS UNIT Devices that can control this unit Broadband router* PREPARATION A Mobile device* (ipod, Android) * You need a commerciall available Wi-Fi broadband router when ou use a mobile device. B Remote control A Control this unit using our mobile devices ( P.3, 12) B Control this unit using the remote control ( P.6, 14, 18, 20, 23) Operations from our mobile device Once ou install the app NETWORK PLAYER CONTROLLER in our mobile device, ou can operate the unit with the mobile device. Features Power-on/off or other basic operation Changing the music source Selecting, plaing back, and stopping songs Plaing back songs stored in devices For downloading the app or the latest information, access to the App Store or Google Pla and search NETWORK PLAYER CONTROLLER. English 3 En

6 OPEN/CLOSE SOURCE REPEAT POP-UP MENU HOME NOW PLAYING SETUP DISPLAY INPUT DIMMER PROGRAM A/B AMP VOLUME PURE DIRECT CLEAR SHUFFLE OPTION MUTE OPEN/CLOSE SOURCE REPEAT POP-UP MENU SETUP DISPLAY INPUT DIMMER PROGRAM A/B HOME AMP VOLUME PURE DIRECT CLEAR SHUFFLE NOW PLAYING OPTION MUTE PUSH PREPARATION Check that ou have received all of the following items. SUPPLIED ACCESSORIES Remote control RCA stereo cable Power cable Batteries (AA, R6, UM-3) ( 2) Owner s manual REMOTE CONTROL PREPARATION Installing the batteries 1 3 Operation range Aim the remote control directl at the remote control sensor on the main unit during operation. Remote control sensor 2 SELECT Notes Change all batteries if the operation range of the remote control narrows. Before inserting new batteries, wipe the compartment clean. Within 6 m (20 ft) En

7 CONTROLS AND FUNCTIONS Front panel SELECT PUSH PREPARATION SOURCE PURE DIRECT A B C 1 Power indicator Lights up: The unit is on. Lights up diml: The unit is in standb mode. Off: The unit is off. When the unit is in standb mode, ou can control the power from a network device (network standb). To enable network standb function, set Sstem Config Network Standb to On from the setup menu ( P.23). 2 Power switch ( P.11) Switches this unit between on and off. : On : Off 3 SOURCE ( P.14, 18, 20) Selects an audio source. Each press ccles the audio sources as follows. CD Spotif Server Net Radio AirPla Back to CD 4 PURE DIRECT Turns on or off PURE DIRECT mode. Audio qualit will be improved when PURE DIRECT mode is on. Note The digital output is turned off when this unit is in PURE DIRECT mode. The PURE DIRECT indicator lights up when PURE DIRECT mode is on. 5 Disc tra Loads a disc. 6 (Open/Close) Opens or closes the disc tra. 7 Front panel displa Shows menu items, plaback information, etc. For details on displa messages, see Front panel displa messages ( P.31). 8 Remote control sensor ( P.4) Receives infrared signals from the remote control. 9 / (Pla/Pause) Starts or pauses plaback. 0 (Stop) Stops plaback. A / (Skip/Search backward) Skips backward. Searches tracks backward while the button is pressed and held during plaback. / (Skip/Search forward) Skips forward. Searches tracks forward while the button is pressed and held during plaback. B SELECT/ (jog dial) ( P.14, 18, 20, 24) Rotate to select an item and press to confirm the selection. C ( P.18, 20) Shows the upper-level menu in the front panel displa. English 5 En

8 CONTROLS AND FUNCTIONS Remote control A B C D OPEN/CLOSE DIMMER SOURCE 1 2 PURE DIRECT PROGRAM CLEAR REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING SETUP DISPLAY OPTION AMP INPUT VOLUME MUTE E F G H I J K L 1 Remote control signal transmitter Transmits infrared signals to the main unit. 2 OPEN/CLOSE Opens or closes the disc tra. 3 DIMMER You can adjust the brightness of the front panel displa in the following three stages: bright, mid dim, or dim. Each press of the button changes the brightness. 4 SOURCE ( P.14, 18, 20) Selects an audio source. Each press ccles the audio sources as follows. CD Spotif Server Net Radio AirPla Back to CD 5 Numeric buttons ( P.15) Use to enter numbers, such as the track number of a CD. 6 REPEAT ( P.15, 19) Switches repeat modes. 7 A/B ( P.16) Repeats plaback of a specified section of a track during audio CD plaback (A-B repeat plaback). 8 POP-UP MENU This button is not available for this unit. 9 HOME ( P.18, 21) Moves up top level when selecting (browsing) music files, folders, etc. 0 / / / (Cursor buttons)/ Use the cursor buttons to select an item and press to confirm the selection. Change the plaback folder or the music file when plaing music files on our data CDs, PC or NAS. A SETUP ( P.23) Shows the setup menu in the front panel displa. B DISPLAY ( P.15, 19, 21) Switches information shown in the front panel displa, such as plaback information. C Plaback buttons ( P.15, 19, 21, 22) (Pla/Pause) Starts or pauses plaback. (Stop) Stops plaback. (Skip backward/search backward) Skips backward. Searches tracks backward while the button is pressed and held during plaback. (Skip forward/search forward) Skips forward. Searches tracks forward while the button is pressed and held during plaback. 6 En

9 CONTROLS AND FUNCTIONS D Amplifier control buttons Controls the corresponding functions of a Yamaha amplifier. A (Power) Turns our amplifier on and off. INPUT ( / ) Switches input sources. VOLUME ( / ) Adjusts the volume. MUTE Turns mute on or off. PREPARATION E F For details on operations, refer to the manual of our amplifier. These buttons ma not work for some Yamaha amplifiers. A (Power) ( P.11) Switches this unit between on and standb mode. PURE DIRECT Turns on or off PURE DIRECT mode. Audio qualit will be improved when PURE DIRECT mode is on. Note The digital output and front panel displa are turned off when this unit is in PURE DIRECT mode. G H CLEAR ( P.16) Clears the last programmed track of an audio CD during program editing mode. Clears all programmed tracks when plaback is stopped while exiting the program mode. PROGRAM ( P.16) Turns on or off program plaback mode. In program plaback mode, ou can plaback tracks of an audio CD in a programmed sequence. I SHUFFLE ( P.15, 19) Switches shuffle modes. J NOW PLAYING ( P.18, 21) Displas plaback information when selecting (browsing) music files, folders, etc. K ( P.18, 21, 23) Moves up one level when selecting (browsing) music files, folders, etc. L OPTION This button is not available for this unit. English 7 En

10 CONTROLS AND FUNCTIONS Rear panel ANALOG OUT terminal ( P.9) Outputs L/R analog audio signals. Connect to our amplifier or audio sstem using the RCA stereo cable (supplied). 2 DIGITAL OUT terminal (COAXIAL) ( P.9) Outputs digital audio signals. Connect to our amplifier or audio sstem using a coaxial digital audio cable (commerciall available). 3 DIGITAL OUT terminal (OPTICAL) ( P.9) Outputs digital audio signals. Connect to our amplifier or audio sstem using an optical cable (commerciall available). 4 NETWORK terminal ( P.10) Connects to a network using a network cable (commerciall available). 5 AC IN socket ( P.9) Connects to an AC outlet using the power cable (supplied). Front panel displa F P A B 1 Information displa Displas various information such as the song title. For more information on the messages displaed, see Front panel displa messages ( P.31). 2 PROGRAM indicator Lights up when the unit is in program plaback mode ( P.16). 3 REPEAT/SHUFFLE indicator ( P.14, 18) Lights up when the unit is in repeat or shuffle mode. Repeat plaback : REPEAT ALL : REPEAT ONE : REPEAT FOLDER : A-B REPEAT Shuffle plaback : SHUFFLE ALL : SHUFFLE FOLDER 8 En

11 CONNECTIONS This section describes connections required before plaing back with this unit. Notes Do not connect the power cable of this unit until all connections are completed. You need to connect this unit to an amplifier and speakers before plaing back. This unit can output digital signals up to 192 khz/24 bits linear PCM signals. Proper plaback ma not be possible depending on the connected device and environment. Verif the settings and specifications of the connected plaback source device. PREPARATION Connecting to an amplifier This unit (CD-N301) 1 ANALOG OUT DIGITAL OUT R L COAXIAL OPTICAL Power cable (supplied) 2 To AC outlet Amplifier Amplifier * The digital output is turned off when this unit is in PURE DIRECT mode. 1 Connect this unit to our amplifier with one of the following cables. 1 RCA stereo cable (supplied) 2 Coaxial digital audio cable (commerciall available) 3 Optical digital cable (commerciall available) 2 Connect the supplied power cable to the AC IN socket, then plug into an AC outlet. For details on speaker connections, refer to the manual of our amplifier or speakers. Note When using a digital connection, audio output ma be interrupted at the beginning of a track depending on the audio sstem (amplifier, etc.). English 9 En

12 CONNECTIONS Connecting to a network (PC/NAS/Internet connection) You can pla back music files stored on our PC or NAS, audio contents on the Internet radio, b connecting this unit to a network. Connect with a commerciall available STP (shielded twisted pair) network cable (CAT-5 or higher, straight-through cable). This unit (CD-N301) Network cable LAN PC Broadband router NAS WAN Modem Internet Notes For details on Internet connection, refer to the owner s manuals of our network devices. If ou are using a router that supports DHCP, ou do not need to configure an network settings for the unit. If ou are using a router that does not support DHCP, configure the network setting from Network Config in the setup menu ( P.23). Wired connections are recommended for devices other than the mobile to ensure high sound qualit. Some securit software installed on our PC or the firewall settings of network devices (such as a router) ma block the access of the unit to the network devices or the Internet. In this case, change the setting of the securit software or network devices. When setting the subnet manuall, each server must be connected to the same subnet as the unit ( P.23). 10 En

13 CONNECTIONS Turning on this unit When ou have established all cable connections, turn on this unit and other sstem components. SOURCE PURE DIRECT SELECT PUSH PREPARATION Press the power switch to turn this unit on. With the power switch on, ou can switch this unit to on or standb mode b pressing the power button on the remote control. When network standb mode is enabled, ou can also control the power etc. from a network device. Operable functions in standb/network standb CD eject AirPla Power-on b the application Standb Operable Network Standb Operable Operable Operable To enable network standb mode, set Sstem Config Network Standb to On from the setup menu ( P.23). When no operations are performed for a specific length of time, the unit automaticall switches to standb mode (auto power standb). You can set the time to switch to standb mode in Sstem Config AutoPowerStdb from the setup menu ( P.23). English 11 En

14 OPERATIONS SETUP OF YOUR NETWORK DEVICES Configure our devices connected to the network to pla back music files stored on the devices, or configure our mobile device to control this unit. Use the following configurations to suit our needs. For details on Internet connection, please refer to the manual of our network devices. If ou want to pla the music files stored on our PC You need to configure the media sharing setting of our PC. Configure the media sharing setting of music files on Windows Media Plaer 12. For details on sharing setting, please refer to Sharing music files stored on our PC ( P.13). You can operate from our PC using Windows Media Plaer. For details, refer to Windows Media Plaer help. If ou want to pla music files stored on our NAS If ou want to pla ipod/itunes with AirPla You need to configure the media sharing settings of our NAS. Setup operations differ depending on our NAS. Refer to the NAS manual. If ou want to configure the network parameters manuall, check that ou are using an IP address which is not used b other network devices in our network. In case that ou use DHCP and automaticall obtain necessar information for network, such as IP address. We recommend that DHCP for the NAS normall be enabled. Select this unit from our ipod or from itunes ( P.22). Check that the router being accessed b the ipod/itunes is connected to the same network as this unit. If ou want to operate this unit with our mobile device You need to download the dedicated application, and install it ( P.3). If ou want to configure the network parameters manuall, check that ou are using an IP address which is not used b other network devices in our network. In case that ou use DHCP and automaticall obtain necessar information for network, such as IP address. We recommend that DHCP for the mobile device normall be enabled. 12 En

15 SETUP OF YOUR NETWORK DEVICES Sharing music files stored on our PC 4 Select Allowed from the drop-down list next to CD-N301. To pla back music files in our computer with this unit, ou need to make the media sharing setting between the unit and computer (Windows Media Plaer 11 or later). For details on Windows Media Plaer, please refer to Windows Media Plaer help. You can connect up to 16 media servers to this unit. When using Windows Media Plaer 12 (on Windows 7) 1 Start Windows Media Plaer 12 on our PC. 2 Select Stream, then Turn on media streaming. 5 In the same wa, select the icons for devices to be used as external media controllers (other PCs or mobile devices), then click Allowed. OPERATIONS 6 Click OK to exit. When using Windows Media Plaer 11 The Control Panel window of our PC appears. 3 Click Turn on media streaming. 1 Start Windows Media Plaer 11 on our PC. 2 Select Librar then Media Sharing. 3 Check the Share m media to box, select the CD-N301 icon, then click Allow. 4 In the same wa, select the icons for devices to be used as external media controllers (other PCs or mobile devices), then click Allow. 5 Click OK to exit. English 13 En

16 SOURCE PURE DIRECT SELECT PUSH SELECT PUSH PLAYBACK OF CDS This unit allows plaback of audio CDs and data CDs in which the MP3/WMA files are recorded. For details on plaable CDs, see PLAYABLE DISCS AND FILE FORMATS ( P.33). Front panel displa (example) CD 1 0:01 3 Press / (main unit) or (remote control) to start plaback. Main unit/remote control Icon The following icons are shown on the front panel displa. Icon Content SETUP DISPLAY OPTION Displaed while a CD is being plaed back. Displaed while a CD is paused. Displaed when a CD is stopped. Plaing back a CD 1 Press SOURCE repeatedl to switch the audio source to CD. Main unit/remote control 4 When plaback starts, use the following controls to operate desired functions. Main unit SELECT/ OPEN/CLOSE DIMMER Plaback buttons SOURCE SOURCE Set the CD. Press the (open/close) button on this unit, or press the OPEN/CLOSE button on the remote control to open the disc tra, and load a disc. SOURCE 4 PURE DIRECT 5 6 SELECT/ Plaback buttons Rotate Press Skips to the next track, or back to the previous track. Plas/Pauses. / Plas/Pauses. Stops plaback. / / Press to skip to the next track, or back to the previous track, or hold down to search backward/ forward. 14 En

17 PLAYBACK OF CDS Remote control Numeric buttons Sets the track number. OPEN/CLOSE DIMMER When a music file is selected: starts plaback. SOURCE PURE DIRECT Plas/Pauses. Numeric buttons Plaback buttons / / Stops plaback. Press to skip to the next track, or back to the previous track, or hold down to search backward/forward. REPEAT 0 PROGRAM CLEAR REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING SETUP SHUFFLE REPEAT Select the repeat plaback method. Audio CD: REPEAT ONE / REPEAT ALL / REPEAT OFF Data CD: REPEAT ONE / REPEAT FOLDER / REPEAT ALL / REPEAT OFF OPERATIONS DISPLAY DISPLAY OPTION Plaback buttons SHUFFLE Select the shuffle plaback method. Audio CD: SHUFFLE ALL / SHUFFLE OFF Data CD: SHUFFLE FOLDER / SHUFFLE ALL / SHUFFLE OFF DISPLAY Change the plaback information. Audio CD (during plaback): Plaing time Time remaining Disc time remaining Song title* Artist name Album title* Data CD (during plaback): Plaing time Song title Artist name Album title * Onl for audio CDs that contain CD-TEXT. Files on a data CD are plaed back in alphanumeric order. When CD plaback is stopped, plaback will resume from the beginning of the song last plaed. Pressing while plaback is stopped will clear resume plaback. You can also check the repeat/shuffle status from the indicators on the front panel displa ( P.8). English 15 En

18 PLAYBACK OF CDS Using A-B repeat plaback During audio CD plaback, A-B repeat plaback allows ou to specif the start and end points for a section that ou want to repeat. A-B repeat plaback is onl available for audio CDs. 1 Plaback the audio CD, and then press the A/B button on the remote control at the point ou want to start the repeat. Using program plaback mode In program plaback mode, ou can pla back tracks in a programmed sequence. Program plaback is onl available for audio CDs. 1 Press PROGRAM on the remote control while plaback is stopped. This unit enters program editing mode PROGRAM CLEAR PROGRAM 0 REPEAT PROGRAM A/B CLEAR SHUFFLE CLEAR A/B REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING POP-UP MENU HOME NOW PLAYING SETUP SETUP DISPLAY OPTION DISPLAY OPTION Front panel displa (example) CD 2 1:25 A B The A-B indicator on the front panel displa flashes during setup. 2 Press the A/B button on the remote control again at the point where ou want to end the repeat. The A-B indicator turns lit, and the repeat plaback starts. 3 To stop the repeat plaback, stop the plaback, or press the A/B button again. The repeat plaback is cancelled. 2 Select a track b using the numeric buttons and press to confirm. 3 Repeat step 2 to program the next track. You can program up to 50 tracks. To cancel the programmed track, press CLEAR during program editing mode. The last programmed track will be deleted. 4 Press / (Pla/Pause) on the main unit or (Pla/Pause) on the remote control. Plaback starts from the beginning of the programmed sequence. To clear all programmed tracks, press CLEAR while plaback is stopped. Note The programmed tracks are cleared when the disc is ejected or this unit is turned off. 16 En

19 PLAYBACK OF SPOTIFY SERVICE Spotif gives ou instant access to millions of songs on our mobile devices. Just hit pla to stream anthing ou like. The Spotif Connect feature lets ou choose music on our Spotif app and listen on our Yamaha home entertainment sstem. See Spotif.com for service area information. 1 Connect our device to our home Wi-Fi network. Connect the unit and our mobile device to our home Wi-Fi network as shown in the illustration below. All devices need to be on the same network. Network connection (example) Internet 3 Turn on the unit and plaback of Spotif contents. Start Spotif app on our mobile device, log in to Spotif and start plaing a track. 1 Tap on the Now Plaing bar to reveal extra controls and tap the Speaker icon. 2 Select the unit (network name of the unit) as the audio output device. Spotif app (example) OPERATIONS Modem Broadband router 1 This unit (CD-N301) 2 Mobile device* * ios/android apps are available as of Jul For more details, visit Spotif.com To use this function, this unit and our mobile device must be connected to the Internet. For detail on connections and network settings, refer to Owner s Manual. The plaback screen is displaed on the front displa. 2 Get Spotif app and premium free trial. Download the Spotif app for our mobile device from our app store, and take the Premium free trial. Spotif and Spotif logo are registered trademarks of the Spotif Group. The Spotif app and Premium account are required. Visit spotif.com for details. English 17 En

20 SOURCE PURE DIRECT SELECT PUSH PLAYBACK OF MUSIC FILES ON YOUR PC/NAS This unit allows ou to pla back music files such as MP3, WMA, or FLAC (lossless audio data compression format) files stored in the computer (server) or NAS connected to the network. Browse the front panel displa and select our favorite music file. To pla back music files in our computer/nas with this unit, ou need to make the media sharing setting to computer/ NAS. For details on sharing setting, please refer to SETUP OF YOUR NETWORK DEVICES ( P.12). For details on plaable music files, see PLAYABLE DISCS AND FILE FORMATS ( P.33). Front panel displa (example) Server Pop/Rock 1 2 The following icons are shown on the front panel displa. 2 Use the following controls to select a desired music file. Main unit 1 Icon Content Displaed when a folder or music file can be selected. Displaed when a folder is selected. Displaed when a supported music file is selected. Displaed while a music file is being plaed back. Displaed while a music file is paused. SELECT/ SELECT/ Rotate Press Selects a folder or music file. When a folder is selected: moves down one level. When a music file is selected: starts plaback. Returns to the previous level. 2 Displaed when there is lower level in the current folder. Remote control REPEAT A/B SHUFFLE Operations from the main unit or remote control HOME POP-UP MENU HOME NOW PLAYING NOW PLAYING 1 Press SOURCE repeatedl to switch the audio source to Server. Main unit/remote control / / SETUP DISPLAY OPTION SOURCE SOURCE OPEN/CLOSE DIMMER SOURCE PURE DIRECT / / HOME / NOW PLAYING Selects a folder or music file. When a folder is selected: moves down one level. When a music file is selected: starts plaback. Returns to the previous level. Moves to the top level. Stops browsing and displas plaback information for the file currentl being plaed. 18 En

21 SELECT PUSH PLAYBACK OF MUSIC FILES ON YOUR PC/NAS 3 When plaback starts, use the following controls to operate desired functions. Main unit Remote control REPEAT 0 PROGRAM CLEAR REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING SHUFFLE SELECT/ SELECT/ Plaback buttons Rotate Press Plaback buttons Skips to the next song, or back to the previous song in the folder. Continues plaback and returns to displa the folders or music files that can be selected. For details on selecting a folder or music file, refer to step 2. Continues plaback and returns to displa the folders or music files that can be selected. For details on selecting a folder or music file, refer to step 2. / Plas/Pauses. / / Stops plaback. Skips to the next song, or back to the previous song in the folder. Plaback buttons REPEAT DISPLAY SHUFFLE / / SETUP DISPLAY OPTION Plas/Pauses. Stops plaback. Plaback buttons Skips to the next song, or back to the previous song in the folder. Continues plaback and returns to displa the folders or music files that can be selected. For details on selecting a folder or music file, refer to step 2. Select the repeat plaback method (REPEAT ONE / REPEAT ALL / REPEAT OFF). Select the shuffle plaback method (SHUFFLE ALL / SHUFFLE OFF). OPERATIONS DISPLAY Changes the plaback information (Song name Artist name Album title Plaing time). You can also check the repeat/shuffle plaback method from the indicators on the front panel displa ( P.8). English 19 En

22 SOURCE PURE DIRECT SELECT PUSH PLAYBACK OF INTERNET RADIO You can listen to world-wide radio stations via Internet. Make sure that the unit is connected to the Internet properl ( P.10). Front panel displa (Example) NetRadio Station List Press SOURCE repeatedl to switch the audio source to Net Radio. Main unit/remote control The following icons are displaed on the front panel displa. OPEN/CLOSE DIMMER Icon Content Displaed when a folder or Internet radio station can be selected. SOURCE SOURCE 4 PURE DIRECT Displaed when a folder is selected. Displaed when Internet radio station is selected. Displaed while a Internet radio station is being plaed back. Displaed when there is lower level in the current folder. SOURCE 2 Selects an Internet radio station from the folder, and press to start plaback. When ou select an internet radio station, panel displa. appears on the front Main unit SELECT/ SELECT/ Rotate Press Selects a folder or Internet radio station. When a folder is selected: moves down one level. When Internet radio station is selected: starts plaback. Returns to the previous level. 20 En

23 SELECT PUSH PLAYBACK OF INTERNET RADIO Remote control HOME REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING NOW PLAYING 3 When plaback starts, use the following controls to operate desired functions. Main unit / / SETUP DISPLAY OPTION / / HOME / NOW PLAYING Selects a folder or Internet radio station. When a folder is selected: moves down one level. When a Internet radio station is selected: starts plaback. Returns to the previous level. Moves to the top level. Stops browsing and displas plaback information for the Internet radio station currentl being plaed. Stops plaback. Remote control DISPLAY SETUP DISPLAY OPTION OPERATIONS Plaback buttons DISPLAY Stops plaback. Changes the plaback information (Station name Plaing time Song title). You can register our favorite Internet radio stations to the Bookmarks folder b selecting Net Radio as the source on the unit and then accessing the following website with the web browser on our PC. Before registering an Internet radio station, pla an Internet radio station with this unit. To use this feature, ou need the vtuner ID of the unit and our address to create our personal account.you can check the vtuner ID (MAC address of the unit) in Network Info ( P.24) in the Setup menu. English 21 En

24 PLAYBACK OF AirPla The AirPla function allows ou to pla back ipod/itunes music on the unit wirelessl via a network. Make sure that the unit and our PC or ipod are connected to the same network ( P.10). Note When ou use ipod/itunes controls to adjust volume, the volume ma be unexpectedl loud. This could result in damage to the unit or speakers. If the volume increases during plaback, stop plaback on ipod/itunes immediatel. You can also use the unit and remote control to pla back, pause, stop, and skip songs. Plaing itunes 1 Turn on the unit and start itunes. If the itunes recognizes the unit, is shown on the screen of itunes. Example Plaing ipod 1 Turn on the unit and displa the plaback screen on the ipod. If the ipod recognizes the unit, is shown on the screen of the ipod. For ipods using ios 7, AirPla is displaed in Control Center. To access Control Center, swipe up from the bottom of the screen. 2 Click and select the unit s name. The source automaticall switches to AirPla (except when network standb is off). Example Example on ios6 Example on ios7 2 Tap and select the unit s name. The source automaticall switches to AirPla and plaback starts. Example 3 Pla back songs with itunes. To control itunes plaback with the remote control, ou need to configure the itunes preferences to enable itunes control from remote speakers in advance. Example of English version Clearing AirPla 1 Tap/click on the ipod/itunes screen and select a device other than CD-N301 from the speaker list. Or, change the source to other than AirPla. 22 En

25 SELECT PUSH SETUP MENU You can configure the various settings of this unit using the setup menu. Setup menu operations Operations from the remote control For details on the controls on the main unit or remote control, see CONTROLS AND FUNCTIONS ( P.5). 1 Press SETUP to enter the setup menu ( P.24). To make the advanced setup menu items ( P.24) selectable, press SETUP while holding down (on the main unit). Remote control SOURCE PURE DIRECT 2 Press / to select a menu item to configure, then press. For some menu items, repeat step 2 to select a submenu item. Sstem Net Standb 3 Press / to select a parameter, then press. You need to enter a numerical address for some menu items. In this case, press / to move the target and / to select a number, or use the numeric buttons. Then press to confirm it. Press the button to return to the previous level. OPERATIONS Numeric buttons PROGRAM CLEAR REPEAT A/B SHUFFLE POP-UP MENU HOME NOW PLAYING / / / / SETUP SETUP DISPLAY OPTION Main unit Front panel displa SETUP Sstem Config English 23 En

26 SETUP MENU Setup menu items Menu Sstem Config Network Info Network Config Submenu Settings (Bold: default) Function Net Standb On, Off Select On to enable the network standb mode. AutoPowerStdb Firm Version Firm Update Network Status MAC Address Sstem ID Network Name DHCP 20min, 2hours, 4hours, 8hours, 12hours, Off On, Off This unit automaticall enters standb mode if it is left turned on for the selected time without plaback or an other operation being performed. The firmware version of this unit is shown. Updates the firmware of the unit ( P.25). The network status of this unit is shown ( Connected or Not connected ). The MAC address of this unit is shown. The MAC address is also used as a vtuner ID. The sstem ID number is shown. Shows the name of the unit that appears on the network. Select On to use the DHCP server to automaticall configure the network settings of this unit or Off to configure manuall. IP Address Specif the IP address when DHCP is Off. *1 Subnet Mask Specif the subnet mask when DHCP is Off. *1 *1: When DHCP is On, ou can check the values (IP address, etc.) assigned b the DHCP server. Advanced setup menu Def. Gatewa Specif the default gatewa when DHCP is Off. *1 DNS Server (P) Specif the primar DNS server when DHCP is Off. *1 DNS Server (S) Specif the secondar DNS server when DHCP is Off. *1 The following menu items are available onl when ou enter the setup menu b pressing SETUP (on the remote control) while holding down (on the main unit). Menu MAC Filter Initialize Settings (Bold: default) On, Off Function Select On to specif the MAC addresses (up to 5) of the network components that will be permitted access to this unit ( Address1 to Address5 ). Select Off to disable the MAC address filter function. Reset the all settings of this unit to factor default. To reset the settings, press SELECT/ on the front panel or on the remote control. The reset operation will be reflected the next time ou turn on this unit. 24 En

27 SETUP MENU Updating the firmware When new firmware is released, a message to update our current firmware will be shown on the front panel displa (when the unit is connected to the Internet onl). 1 Press SETUP. The setup menu is shown on the front panel displa. Remote control POP-UP MENU HOME NOW PLAYING / / SETUP SETUP OPERATIONS DISPLAY OPTION 2 Select Sstem Config with / and press. 3 Select Firm Update with / and press. 4 Press again. Update starts. Network S2:Writing 56% When update finishes, messages are shown in the following order: Update success., Please, and power off!. 5 Unplug the power cable from the wall outlet and plug it back after about 30 seconds. Update is applied. Note Do not operate the unit or disconnect the power cable and network cables while updating. Once the message prompting update is shown on the front panel displa, it will not be shown again, even if ou do not perform updating. However, when ou turn on the unit after the power cable has been disconnected from the wall outlet for a while, the message will be shown. When Internet speed is not fast enough or the unit is connected to the wireless network via a wireless network adapter, network update ma not be possible depending on the condition of the wireless connection. In this case, tr again. English 25 En

28 OTHERS FREQUENTLY ASKED QUESTIONS What kind of settings do I need to make? For details on settings of our PC, NAS or mobile devices, see SETUP OF YOUR NETWORK DEVICES ( P.12). For details on the setup menu on this unit, see SETUP MENU ( P.23). Wh can t I find music files on m PC? Check the media sharing settings of our PC or media server, such as Windows Media Plaer 12 ( P.12). Check if the music files are plaable ( P.33). Can I control this unit with m iphone? For details on controlling this unit from our mobile device, see Operations from our mobile device ( P.3). I can t find this unit using the dedicated application installed on m mobile device! Check if this unit is properl connected to the same network via the broadband router. Check if access to this unit is restricted b MAC address filter function ( P.28). What music files are plaable on this unit? For details on plaable files and formats, see PLAYABLE DISCS AND FILE FORMATS ( P.33). How can I listen to Internet radio on this unit? For details on listening to Internet radio stations, see PLAYBACK OF INTERNET RADIO ( P.20). How do I pla back m ipod/itunes with AirPla? For details on plaback, see PLAYBACK OF AirPla ( P.22). What do the messages on the front panel displa stand for? For details on the front panel displa messages, see Front panel displa messages ( P.31). For latest information, please visit Yamaha website. 26 En

29 TROUBLESHOOTING Refer to the table below when this unit does not function properl. If the problem ou are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. General Problem Cause Remed Page This unit fails to turn on. The power indicator on the front panel flashes. This unit suddenl turns off. No sound. Noise is heard. The power cable is not connected to the AC IN socket on the main unit or not plugged into an AC outlet. This unit has been exposed to a strong external electric shock (such as lightning or strong static electricit). The protection circuitr has been activated three times consecutivel. When this unit is in this condition, the power indicator on the main unit blinks if ou tr to turn on the power. There is a problem with the internal circuitries of this unit. This unit entered standb mode. The audio cable connection between this unit and amplifier is improper. The input setting on the amplifier is incorrect. The amplifier is not compatible with the digital signals. This unit is too close to the digital or radio-frequenc equipment. The audio cable between this unit and the media sever is defective. Connect the power cable firml. 9 Turn off this unit, disconnect the power cable, plug it back in after 30 seconds, then use it normall. As a safet precaution, capabilit to turn on the power is disabled. Contact our nearest Yamaha dealer or service center to request repair. Turn off this unit, disconnect the power cable, then contact the nearest authorized Yamaha dealer or service center. This unit enters standb mode after the time set for Auto Power Stdb in the setup menu has elapsed. Connect the audio cable firml. If the problem persists, use another audio cable. Select the correct input (from this unit) on the amplifier. Use an analog signal connection. Move this unit awa from such equipment. Connect the audio cable firml. If the problem persists, use another audio cable OTHERS English 27 En

30 TROUBLESHOOTING Problem Cause Remed Page The remote control does not work or function properl. The amplifier control buttons on the remote control do not work on the amplifier. Wrong distance or angle. Direct sunlight or lighting is striking the remote control sensor of this unit. The batteries are weak. Your amplifier is not one of Yamaha amplifiers. (These buttons ma not work on some Yamaha amplifiers.) The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees off-axis from the front panel of the main unit. Adjust the lighting angle, or reposition this unit. Replace both batteries with new ones. Use the remote control of our amplifier. 4 4 Network Problem Cause Remed Page The network feature does not function. This unit does not detect the digital media server (PC). The network parameters (IP address) have not been obtained properl. The media sharing setting is not correct. Some securit software installed on our PC is blocking the access of this unit to our PC. This unit and our PC are not in the same network. Access to this unit is restricted b MAC address filter function. There are more than two routers in use that are overlapping among the network devices. Enable the DHCP server function on the broadband router and set DHCP in the setup menu to On on this unit. If ou want to configure the network parameters manuall, check that ou are using an IP address which is not used b other network devices in our network. Configure the media sharing setting of our PC. Check the settings of securit software installed on our PC. Check the network connections and the broadband router settings, then connect this unit and our PC to the same network. Disable MAC address filter function in the setup menu of this unit. Disconnect the Internet connection temporaril and check via our local network, or connect the network devices ou want to use to the same router En

31 TROUBLESHOOTING Problem Cause Remed Page The files in our PC cannot be viewed or plaed back. Some audio files cannot be plaed back on this unit. The files are not supported b this unit or the media server. You are tring to pla back DRM audio files ou purchased on itunes Store. Use the file format supported b both this unit and the media server. For details on the supported file formats b the unit, see PLAYABLE DISCS AND FILE FORMATS. You cannot pla back DRM audio files ou purchased on itunes Store Internet radio Problem Cause Remed Page The Internet radio cannot be plaed. The selected Internet radio station is currentl not available. The selected Internet radio station is currentl broadcasting silence. Access to the network is restricted b the firewall settings of our network devices (such as the broadband router). There ma be a network problem at the radio station, or the service ma have been stopped. Tr the station later or select another station. Some Internet radio stations broadcast silence at certain of times of the da. Tr the station later or select another station. Check the firewall settings of our network devices. The Internet radio can be plaed onl when it passes through the port designated b each radio station. The port number varies depending on the radio station. OTHERS English 29 En

32 TROUBLESHOOTING CD Problem Cause Remed Page The disc tra does not close completel. Disc plaback does not start. Disc plaback does not start. Plaback is delaed, or begins at the wrong place. A foreign object is obstructing the tra. The disc is damaged. There is moisture on the laser pickup. The disc is loaded upside down. Carefull check the disc tra and remove the foreign object. Check the disc carefull and replace it if necessar. Wait 20 to 30 minutes after turning this unit on before tring to pla back a disc. Reload the disc with the label side up. The disc is dirt. Clean the disc. 33 The format of the MP3 or WMA file is not compatible with this unit. The CD-RW (ReWritable) disc is not recorded correctl. The disc is a non-standard disc not plaable with this unit. The disc is scratched or damaged. Replace the disc with a correctl recorded disc plaable with this unit. Replace the disc with a correctl recorded disc plaable with this unit. Replace the disc with a correctl recorded disc plaable with this unit. Check the disc carefull and replace it if necessar. Noise from inside of the disc tra. The disc is warped. Replace the disc En

33 TROUBLESHOOTING Front panel displa messages Message Access error Connected Initializing List updated LOADING No content NO DISC Not available Not Connected OPEN Program Clear Searching Unknown DISC Unsupported Status There is a problem with the signal path from the network to the unit. Connected to the network. Initializing the network settings. The content list of the media server has been updated. The specified content is being loaded. This unit cannot find an content. A CD is not inserted in the disc tra. The operation ou have performed is not available. Cannot connect to the network. The CD tra is open. The programmed track has been cleared. This unit is searching for content. An unsupported disc has been inserted. Cannot pla the specified contents. OTHERS English 31 En

34 SOURCE PURE DIRECT SELECT PUSH ADDITIONAL INFORMATION This section describes about general ideas of DLNA (Digital Living Network Alliance) and NAS (Network Attached Storage). Internet DLNA Modem PC (Digital Media Server) Broadband router This unit (CD-N301) (Digital Media Renderer) NAS (Digital Media Server) Mobile device (Digital Media Controller) DLNA DLNA stands for Digital Living Network Alliance, and is a guideline to promote standardization of interconnection of home network devices such as digital consumer electronics. DLNA components are separated into four device classes: Digital Media Server (DMS), Digital Media Renderer (DMR), Digital Media Plaer (DMP) and Digital Media Controller (DMC). Digital Media Server (DMS) is a device that is used to store or distribute digital contents such as music files. For the sstem using this unit, PCs and NAS are regarded as Digital Media Server (DMS). Digital Media Controller (DMC) is a device to control digital contents. The dedicated mobile device application corresponds to Digital Media Controller (DMC) for the sstem using this unit. Digital Media Renderer (DMR) is a device to receive instructions from Digital Media Controller (DMC) and pla back digital contents such as this unit. Similarl, Digital Media Plaer (DMP) is a device that can pla back digital contents stored on Digital Media Server (DMS). NAS NAS stands for Network Attached Storage. B connecting our NAS and home network with a network cable directl, NAS can be a storage device, such as a hard disc drive. If our NAS is compatible with DLNA, ou can share our music, pictures, or movies on the same home network as a digital media server. 32 En

35 PLAYABLE DISCS AND FILE FORMATS Plaable media and devices Supported PC PC with Windows Media Plaer 11 or Windows Media Plaer 12 installed. Supported NAS NAS that is compatible with DLNA version 1.5. Supported mobile devices For details, please visit Yamaha website. Notes Do not use an nonstandard shaped disc (heart, etc.) available on the market because it might damage the unit. Do not use a disc with tape, stickers, or paste on it. If ou use such a disc, the disc ma get stuck in the unit, or damage to the unit ma result. About handling discs Alwas handle with care so that the plaing surface is not scratched. Do not warp discs. Plaable discs Use compact discs bearing the marks below. Mark Details Compact discs (digital audio) To keep clean the plaing surface, wipe with a clean, dr cloth. Do not use an tpe of disc cleaner, spra, or an other chemical-based liquid. Do not wipe with a circular motion; wipe straight outward from the center. OTHERS CD-R, CD-RW digital audio discs CD-R or CD-RW discs bearing one of the following phrases. FOR CONSUMER FOR CONSUMER USE FOR MUSIC USE ONLY Finalized CD-R or CD-RW discs onl. Note This unit ma not be able to pla some CD-R/ CD-RW discs or discs on which recording was not made correctl. CD-TEXT discs The disc title, artist name, and track name are also displaed in addition to the time displas when plaing back a CD with CD TEXT. To pla back an 8-cm (3-inch) CD Place it in the inner recessed area of the disc tra. Do not put a normal 12-cm (5-inch) CD on top of an 8-cm (3- inch) CD. Use a soft-tipped pen when writing on the label side of the disc. When a disc is not being used, remove it from this unit and store in an appropriate case. Do not expose discs to direct sunlight, high temperature or high humidit for a long time. Note Do not use an lens cleaners as the ma be a cause of malfunction. English 33 En