Please read this! DORADO 6-QUBE INSTALLATION INSTRUCTIONS
|
|
- Gonzalo Contreras Lucero
- hace 5 años
- Vistas:
Transcripción
1 INSTALLATION INSTRUCTIONS Please read this! Warning: Read and follow installation instructions for proper installation. Improper installation will void warranty and can cause damage to the fixture. 1 This fixture must be installed with gaskets located between the fixture and pole mount, as well as pole mount and pole (see figure A). 2 After wire connections have been made to the power sources, the wire location entry location into the fixture must be sealed with silicone. This includes the two pole mount studs (see figure B). FIGURE A Gasket Gasket FIGURE B Silicone CORRECT INCORRECT See next page for full installation instructions.
2 INSTALLATION INSTRUCTIONS Remove warning label to expose hidden screw The installation must only be performed by a licensed electrician. To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada. Disconnect power before installing the product or servicing it. Wait until fixture has cooled down before installing or servicing the fixture. Water in the fixture voids warranty. MIN. 90 C SUPPLY CONDUCTORS Read and follow installation instructions. Improper installation will void warranty Turn off power to the light pole at circuit breaker. Unbox the Dorado from packaging and remove the back housing from the Dorado fixture. Note: one of the three screws is under warning label. Determine type of mount to be used and follow appropriate steps shown below. Pole Mount A. Drill necessary holes into pole for fixture mounting (FIG 1). B. Remove pole cap and lower nut plate inside of pole until threaded holes align with proper mounting holes. C. Assemble threaded rods into nut plate and slide on gaskets and spacer block (FIG 2). D. Affix Dorado back housing to pole using washer plate, lock washers, and nuts. E. Fish power leads through pole mount into the Dorado back housing. Slip-Fitter Mount A. Slide slip-fitter mount over pole. B. Secure by tightening set screws (FIG 3). C. Affix Dorado back housing to mount using mount screws, washer plate, lock washers, and nuts. D. Fish power leads through mount into Dorado back housing. E. Adjust fixture angle to 45 by loosening position locking screw and rotating into position. Tighten position locking screw. Trunnion Mount A. Affix bracket surface mount to mounting surface using appropriate hardware (supplied by installer) (FIG 4). B. Affix fixture to mount using fixture mounting screws, lockwashers, washers and nuts (FIG 4). C. Adjust fixture position angle by removing position locking screw, loosening pivot screw rotating to designated position, tightening pivot screw and replacing locking screw (FIG 4). D. Run power to the Dorado back housing using a liquid tight 1/2 conduit fitting (supplied by installer). FIG 1 FIG 2
3 INSTALLATION INSTRUCTIONS Hang Dorado front housing onto hinges located on the Dorado back housing. Follow wiring diagram to make electrical connections per local and national electric codes. Seal wire entry locations with silicone as described on front page. Rotate Dorado front housing closed ensuring no wires or debris is interfering with the gasket surface. Tighten 3 screws captivated in Dorado front housing. Caution: do not use power tools to install, over torquing can damage fixture. Adjust Slip-Fitter or Trunnion mount to desired angle. Insure all holes in pole and pole cap are sealed water tight. Insure gaskets are sealed. If any doubt, caulk the seam. QD1-X-UNVX-XX-50-6-X: has 15 LEDs per module, and 2 power supplies QD1-X-UNVX-XX-50-5-X: has 11 LEDs per module, and 2 power supplies QD1-X-UNVX-XX-50-4-X: has 8 LEDs per module, and 1 power supply FIG 3 FIG 4
4 INSTRUCCIONES DE INSTALACIÓN Lea lo siguiente! Advertencia: Lea y siga las instrucciones de instalación para realizar la instalación correcta. Una instalación incorrecta anulará la garantía y puede provocar daños en el dispositivo. 1 Este dispositivo debe ser instalado con las juntas situadas entre el dispositivo y el soporte del poste, así como el soporte del poste y el poste (ver la figura A). 2 Después de realizar las conexiones de los cables a las fuentes de alimentación, la ubicación de la entrada del cable en el dispositivo se debe sellar con silicona. Se incluyen los dos pernos de montaje del poste (ver la figura B). FIGURA A Junta Junta FIGURA B Silicona CORRECTO INCORRECTO Consulte la página siguiente para obtener las instrucciones completas de instalación.
5 INSTRUCCIONES DE INSTALACIÓN Retire la etiqueta de advertencia para exponer el tornillo ocultos. La instalación debe ser realizada únicamente por un electricista autorizado. Para evitar la muerte, lesiones o daños a la propiedad, este producto debe ser instalado de acuerdo con el Código Eléctrico Nacional (NFPA70) en los EE. UU. o el Código Eléctrico Canadiense (CSA22.1) en Canadá. Desconecte el suministro de energía antes de instalar el producto o darle mantenimiento. Espere hasta que el dispositivo se enfríe antes de instalarlo o darle mantenimiento. Si se encuentra agua en el dispositivo, se cancelará la garantía. CONDUCTORES DE ALIMENTACIÓN MÍN. DE 90 C Lea y siga las instrucciones de instalación. La instalación incorrecta anulará la garantía Desconecte el suministro de energía del poste de luz en el disyuntor. Retire el dispositivo del Dorado de su empaque y retire la carcasa posterior del dispositivo. Nota: uno de los tres tornillos está debajo de la etiqueta de advertencia. Determine el tipo de montaje que se va a utilizar y siga los pasos adecuados que se muestran a continuación. Soporte del poste A. Perfore los orificios necesarios en el poste para el montaje del dispositivo (FIG. 1). B. Retire la tapa del poste y baje la placa con tuerca dentro del poste hasta que los orificios roscados queden alineados con los orificios de montaje adecuados. C. Ensamble las varillas roscadas en la placa con tuerca y deslícelas sobre las juntas y el bloque distanciador (FIG. 2). D. Fije la carcasa posterior del Dorado en el poste utilizando la placa con arandela, las arandelas de bloqueo y las tuercas. E. Pase los cables de alimentación a través del montaje del poste en la carcasa posterior del Dorado. Soporte Slip-Fitter A. Deslice el soporte Slip-Fitter en el poste. B. Fije apretando los tornillos de ajuste (Fig. 3). C. Fije la carcasa posterior del Dorado en el soporte utilizando los tornillos para el soporte, la placa con arandela, las arandelas de bloqueo y las tuercas. D. Pase los cables de alimentación a través del soporte en la carcasa posterior del Dorado. E. Ajuste el ángulo de montaje a 45 aflojando el tornillo de bloqueo de posición y girándolo en su posición. Ajuste el tornillo de bloqueo de posición. Montaje del muñón A. Fije el soporte de superficie en la superficie de montaje utilizando los accesorios apropiados (suministrados por el instalador) (FIG. 4). B. Fije el dispositivo al soporte con los tornillos de montaje, las arandelas de bloqueo, las arandelas y las tuercas (Fig. 4). C. Ajuste el ángulo de posición del dispositivo retirando el tornillo de bloqueo de posición, soltando el tornillo de pivote girándolo hasta la posición designada, ajustando el tornillo de pivote y reemplazando el tornillo de bloqueo (FIG. 4). D. Aplique corriente a la carcasa posterior del Dorado utilizando una conexión de conducto impermeabilizado de 1/2 (suministrado por el instalador). FIG 1 FIG 2
6 INSTRUCCIONES DE INSTALACIÓN Cuelgue la carcasa delantera del Dorado en las bisagras ubicadas en la carcasa posterior del Dorado. Siga el diagrama de cableado para hacer las conexiones eléctricas de acuerdo con los códigos eléctricos locales y nacionales. Selle las entradas del cable con silicona tal como se describe en la primera página. Gire la carcasa delantera del Dorado asegurándose de que no haya cables o desechos que interfieran con la superficie de la junta. Ajuste los 3 tornillos en la carcasa delantera del Dorado. Precaución: no use herramientas eléctricas para la instalación, ya que si ajusta en exceso, puede dañar el dispositivo. Ajuste el soporte de Slip-Fitter o de muñón en el ángulo deseado. Asegúrese de que todos los agujeros en el poste y el tapón del poste estén sellados herméticamente. Asegúrese de que las juntas están selladas. Si tiene alguna duda, calafatee la junta. QD1-X-UNVX-XX-50-6-X: tiene 15 LEDs por módulo y 2 suministros de energía QD1-X-UNVX-XX-50-5-X: tiene 11 LEDs por módulo y 2 suministros de energía QD1-X-UNVX-XX-50-4-X: tiene 8 LEDs por módulo y 1 suministro de energía FIG 3 FIG 4
7 INSTALLATION INSTRUCTIONS DORADO 6-QUBE WIRING DIAGRAMS
8 INSTALLATION INSTRUCTIONS DORADO 6-QUBE WIRING DIAGRAMS
Delivery & Installation Pointer
DP-035 August 2009 R8178785 Delivery & Installation Pointer ISSUE: August 2009 Whirlpool 27 French Door with IDI Models: GI7FVCXWA, GI7FVCXWB, GI7FVCXWQ, GI7FVCXWY Supplemental Information Accessing Door
Más detallesINSTRUCCIONES DE ENSAMBLAJE.
English MULTI-FUNCTIONAL COMPUTER TABLE ASSEMBLY INSTRUCTION MODEL RTA - S06 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesPreassembled Rail Instructions
Preassembled Rail Instructions Prior to installing railing: Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. All supporting structures must be in
Más detallesModel :RFBW01014 Model :RFBE Model :RFBG 01014
Model :RFBW01014 Model :RFBE 01014 Model :RFBG 01014 Wall Cabinet Operators Manual Manual de Operadora del Gabinete de pared Inspect product prior to installation. Contact info@runfinegroups.com prior
Más detallesMT442 MT642 U S E R S M A N U A L
T I L T S L I M M O U N T Display Size: 24-55 Maximum load: 70 lbs / 32 kg VESA Patterns: 75 x 75 to 400 x 400 Display Size: 30-65 Maximum load: 75 lbs / 34 kg VESA Patterns: 75 x 75 to 600 x 400 MT442
Más detallesLight Package Switches Interruptores ligeros del Paquete
Light Package Switches Interruptores ligeros del Paquete Rev. C 2018 Hoffman Enclosures Inc. PH 763 422 2211 nvent.com/hoffman P/N 36301001 87566341 GENERAL SAFETY INFORMATION 1. Before installing switches,
Más detallesLight Package Switches Interruptores ligeros del Paquete
Hoffman Enclosures Inc. 2100 Hoffman Way Anoka, MN 55303 1745 (763) 422 2211 www.hoffmanonline.com Light Package Switches Interruptores ligeros del Paquete Rev. B 111550 2004 Hoffman Enclosures Inc. P/N
Más detallesINSTRUCTION MANUAL Smart Security Light
SPL06-07A1W1-BKT-K1 INSTRUCTION MANUAL Smart Security Light Questions, problems, or missing parts? Before returning to the store, call MAXIMUS customer service at 1-866-897-2098, Monday Friday, 9:30am
Más detalles2011 Honda CR-Z
INSTALLATION INSTRUCTIONS FOR PART 99-7879 APPLICATIONS 2011 Honda CR-Z 99-7879 KIT FEATURES ISO radio mount provision with pocket KIT COMPONENTS A) Radio housing B) ISO brackets C) Pocket D) (11) #8 x
Más detallesAdd Counterweights for Opus Bedside Tables - HT18MAL and HT18MBL
HEALTH Add Counterweights for Opus Bedside Tables - HT18MAL and HT18MBL CAUTION FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Read the entire Assembly Direction
Más detallesLine Neutral Bus Bar Assembly and Lug Replacement Kit for 200 A Combination Service Entrance Device Class 4120
Instruction Bulletin 40273-369-01 01/2004 Lexington, KY, USA Line Neutral Bus Bar Assembly and Lug Replacement Kit for 200 A Combination Service Entrance Device Class 4120 Retain for future use. ENGLISH
Más detallesINSTRUCCIONES DE ENSAMBLAJE.
English MULTI-FUNCTIONAL COMPUTER TABLE ASSEMBLY INSTRUCTION MODEL RTA - 3806 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesRTA-B002 DIMENSIONS MAXIMUM WEIGHT CAPACITIES. Highest position. Lowest position. Product Size: 22"W x 16"D x 30.5~46.5"H
MODEL RTA - B002 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference. MODEL RTA-B002 MODELO
Más detallesInstallation Guide. Green momit
Installation Guide Green momit 2015 www.momit.com momit Deviceses Gateway: Model 1 and 2 Wall option The momit Gateway allows your thermostat to be connected to the Internet. It s included in the Starter
Más detallesMF222 U S E R M A N U A L
S L I M F L A T M O U N T Display Size: 10-40 Maximum load: 44 lbs / 20 kg VESA Patterns: 75 x 75 to 200 x 200 MF222 U S E R M A N U A L ATTENTION: BEFORE INSTALLING, READ ALL WARNINGS AND CAUTIONS ON
Más detallesLIRIC SERIE MODEL LIRIC 8 / LIRIC 6 / LIRIC 5
LIRIC SERIE MODEL LIRIC 8 / LIRIC 6 / LIRIC 5 ENGLISH INSTALLATION manual INSTALLATION INSTRUCTION FOR SURFACE MOUNT BOX TYPE SPEAKER MODEL: LIRIC 5 / LIRIC 6 / LIRIC 8 1) When mounting speakers, use the
Más detallesRTA-2706A DIMENSIONS
MODEL RTA - 706A Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference. MODEL RTA-706A MODELO
Más detallesKAWASAKI VERSYS
Montaje para Soporte de exploradora. Nota: No apriete todos los tornillos hasta que no estén completamente alineadas todas las perforaciones con respecto a los puntos de sujeción. y las piezas esten completas.
Más detalles8 BIN WOODEN STORAGE ORGANIZER ORGANIZADOR DE 8 CAJONES DE TELA
MODEL: 11223768V / MODELO: 11223768V 8 BIN WOODEN STORAGE ORGANIZER ORGANIZADOR DE 8 CAJONES DE TELA PARTS LIST AND HARDWARE LISTA DE PARTES Y ACCESORIOS NO A B C D E F G H1 H2 I J K L M N O HARDWARE LIST
Más detallesLAPTOP DESK WITH 3 BINS MESA PARA COMPUTADORA PERSONAL CON 3 CONTENEDORES
MODEL: 11222775R / MODELO: 11222775R LAPTOP DESK WITH 3 BINS MESA PARA COMPUTADORA PERSONAL CON 3 CONTENEDORES NO A B C D E F G H 1 2 3 4 5 6 7 8 9 PARTS AND HARDWARE LISTA DE PARTES Y HARDWARE TOP PANEL
Más detallesINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Scion xa up. tc WIRING & ANTENNA CONNECTIONS (sold separately)
KIT FEATURES INSTALLATION INSTRUCTIONS FOR PART 99-8209 DIN radio provision with pocket ISO mount radio provision with pocket KIT COMPONENTS 99-8209 A APPLICATIONS Scion xa 2004-2006 xb 2004-up tc 2005-2010
Más detallesCHANDELIER Instruction Manual SAFETY READ & SAVE THESE INSTRUCTIONS UNPACK THE PACKAGE INSTALLATION & OPERATION INSTRUCTIONS GENERAL
CHANDELIER Instruction Manual Please read carefully and save these instructions, as you may need them at a later date. SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF;
Más detallesdash LED Light Luz LED dash INTEGRATED & SOTO RAILS RIELES INTEGRADOS Y SOTO
dash LED Light Luz LED dash INTEGRATED & SOTO RAILS RIELES INTEGRADOS Y SOTO M HEX LLAVE HEX M b e a c d SIDE VIEW VISTA LATERAL FREESTANDING BASE BASE AUTÓNOMA ON OFF ON OFF If you have a problem, question,
Más detallesSP-U. Soporte colgado universal para JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15
Soporte colgado universal para JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15 Universal U-bracket for JK26 / JK10 / JK10MA / JK12 / JK12MA / JK15 / KEY10 / KEY12 / KEY15 Copyright
Más detallesMODEL: F / MODELO: F END TABLE WITH MEDIA STAND & MAGAZINE HOLDER MESA RINCONERA CON ESTANTE & REVISTERO
MODEL: 11225479F / MODELO: 11225479F END TABLE WITH MEDIA STAND & MAGAZINE HOLDER MESA RINCONERA CON ESTANTE & REVISTERO NO A B C D E F G H I J K L PARTS LIST AND HARDWARE PARTES Y ACCESORIOS PARTS LIST
Más detallesINSTRUCTION, IN CAB ON/OFF SWITCH KIT P/N
LIFT CORPORATION Sht. 1 of 10 DSG# M-88-38 Rev. B Date: 06/21/17 INSTRUCTION, IN CAB ON/OFF SWITCH KIT P/N 250477 CABLE, 16-AWG 3-CONDUCTOR, 540 LG. P/N 051076-14 QTY. 1 DECAL P/N 260941 QTY. 1 SWITCH,
Más detallesBASE & WALL EASY REACH CABINET 170º Hinge Replacement
These instructions should only be printed using Adobe Acrobat and should not be faxed or reproduced on a digital copier. American Woodmark Corporation provides these instructions on an AS IS basis and
Más detallesMANUAL DE INSTRUCCIONES SOPORTE PARA TV LED/LCD (23 42 ) WM-5293
MANUAL DE INSTRUCCIONES SOPORTE PARA TV LED/LCD (23 42 ) WM-5293 ESTIMADO CLIENTE Con el fin de que obtenga el mayor desempeño de su producto, por favor lea este manual de instrucciones cuidadosamente
Más detallesMeijer.com A
English MOBILE LAPTOP CART STORAGE ASSEMBLY INSTRUCTION MODEL RTA - B00 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Scion xa xb tc xd
KIT FEATURES INSTALLATION INSTRUCTIONS FOR PART 99-8230 DIN head unit provision with pocket ISO DIN head unit provision with pocket KIT COMPONENTS A 99-8230 B APPLICATIONS Scion xa 2004-2006 xb 2004-2011
Más detallesWALL MOUNTING REQUIRED
WALL MOUNTING REQUIRED LOCATING HEATER: This heater is designed to be mounted on a wall only. It will not operate as a freestanding heater and should not be modified to do so. For convenience and efficiency,
Más detallesBUILT-IN TRIM KIT INSTALLATION INSTRUCTION
BUILT-IN TRIM KIT INSTALLATION INSTRUCTION FOR KENMORE TRIM-KIT MODEL - 30 : 63002, 63004, 63009, 64003 27 : 63012, 63014, 63019, 63013 FOR USE WITH KENMORE MICROWAVE OVEN MODEL: 721.62462200, 721.62463200,
Más detallesCadillac Catera DeVille (column shift only)
INSTALLATION INSTRUCTIONS FOR PART 99-2004 APPLICATIONS DeVille 1996-1999 (column shift only) 99-2004 KIT FEATURES DIN Radio provision with pocket ISO DIN Radio provision with pocket KIT COMPONENTS (A)
Más detallesWarning: Prior to operating, make sure the electrical outlet is of the configuration and capacity appropriate for the heater.
Warning: Prior to operating, make sure the electrical outlet is of the configuration and capacity appropriate for the heater. DANGER ELECTRIC SHOCK OR FIRE HAZARD READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS,
Más detallesSteel Workbench Frame
INSTRUCTIONS Adjustable Height and Length Steel Workbench Frame LENGTH ADJUSTABLE FOR 4', 5', 6' WORK SURFACES 29" - 41" ADJUSTABLE HEIGHT (1" INCREMENTS) WORK SURFACE NOT INCLUDED USE 4', 5', 6' LONG
Más detallesScion IQ 2012-up
INSTALLATION INSTRUCTIONS FOR PART 99-8234 APPLICATIONS Scion IQ 2012-up 99-8234 KIT FEATURES DIN head unit provision with pocket ISO DIN head unit provision with pocket KIT COMPONENTS A) Radio Housing
Más detallesPackage Contents. Hardware Package. Tools Needed
Reverso en español HWGWTR-1 REAR REGISTER KIT INSTALLATION INSTRUCTIONS INSTRUCTIONS MUST BE LEFT WITH THE OWNER FOR FUTURE REFERENCE AFTER INSTALLATION. Package Contents REGISTER BOOT REGISTER WITH DAMPER
Más detallesINSTALLATION INSTRUCTION Vogue WS-3120
WS-3120 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance
Más detallesArtefacto de iluminación de doble función
Artefacto de iluminación de doble función Owner s Guide and Installation Manual Manual De Propietario English Español Formulario# 43550-02 20100610 2010 Hunter Fan Co. Bienvenido Su nuevo artefacto de
Más detallesINSTRUCCIONES DE ENSAMBLAJE.
English MULTI-FUNCTIONAL COMPUTER TABLE ASSEMBLY INSTRUCTION MODEL RTA - 3327 IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesUniversal CF-104UD, SEA/HOS, SEA/HOS-W
INSTALLATION INSTRUCTIONS FOR PART 99-9000 KIT FEATURES DIN head unit provision Various mounting depths APPLICATIONS Universal 99-9000 CF-104UD, SEA/HOS, SEA/HOS-W Table of Contents Dash Disassembly All
Más detallesRTA-3325 DIMENSIONS MAXIMUM WEIGHT CAPACITIES. Product Size: 60"W x 23.5"D x 35"H
MODEL RTA-3325 MODELO RTA - 3325 Gracias por comprar uno de nuestros productos. Por favor lea cuidadosamente las instrucciones de ensamblaje antes de instalar la unidad. Por favor guarde este manual para
Más detalles#10 x 3-in Washer Head Screw #8 x 3/4-in Truss Head Screw
Floating Shelf 2-ct #6 x 3/4-in Screw Wood Mounting Plate 2-ct Metal Bracket 4-ct 4-ct #10 x 3-in Washer Head Screw #8 x 3/4-in Truss Head Screw Floating Shelf Floating Shelf Includes: 1-ct - Floating
Más detallesINSTRUCTION, DUAL STEP INSTALLATION KIT
LIFT CORPORATION Sht. 1 of 10 DSG# M-05-01 Rev. F Date: 07-06-17 INSTRUCTION, DUAL STEP INSTALLATION KIT NOTE: There are 8 separate step kits. KIT P/N 281311-01 (See TABLE 2-1.) KIT P/N 281312-02 (See
Más detallesHighbay Installation Instruction-Mounting Hook
Highbay Installation Instruction-Mounting Hook Please read the instructions before installation. NOTES: 1 Turn power off before inspection, installation or removal. 2. LED fixture requires 120-277V input
Más detalles3 PIECE BAR SET JUEGO DE BAR DE 3 PIEZAS
MODEL: 11222152VW / MODELO: 11222152VW 3 PIECE BAR SET JUEGO DE BAR DE 3 PIEZAS NO A B C D E F G H I J K L M N O P1 P2 Q PARTS LIST AND HARDWARE LISTA DE PARTES Y ACCESORIOS HARDWARE LIST LISTA DE ACCESORIOS
Más detalles4 DRAWER ORGANIZER ORGANIZADOR DE 4 CAJONES
MODEL: 11210913 / MODELO: 11210913 DRAWER ORGANIZER ORGANIZADOR DE CAJONES NO N o 1 2 3 NO N o A B C D E PARTS LIST AND HARDWARE LISTA DE ACCESORIOS Y PARTES HARDWARE LIST / LISTA DE ACCESORIOS SCREW /
Más detallesSUSTITUCIÓN DE TUBOS FLUORESCENTES POR TUBOS DE LEDs CHANGING FLUORESCENT TO LED TUBES
SUSTITUCIÓN DE TUBOS FLUORESCENTES POR TUBOS DE LEDs CHANGING FLUORESCENT TO LED TUBES 1 ES En las instalaciones convencionales de tubos fluorescentes se precisaban tanto cebadores, principalmente utilizados
Más detallesLine Neutral Lug Replacement Kit for 200 A Underground Feed Combination Service Entrance Device Class 4120
Instruction Bulletin 40273-361-01 01/2004 Lexington, KY, USA Line Neutral Lug Replacement Kit for 200 A Underground Feed Combination Service Entrance Device Class 4120 Retain for future use. ENGLISH Table
Más detallesInstructions for Dual Flush Tank Lever
10071 nstsheet_nal 4/28/10 4:35 PM Page 1 nstructions for ual lush Tank Lever 1. Turn off water supply to toilet. lush toilet to drain water from toilet tank. isconnect chain (A) from existing tank lever
Más detallesINSTRUCTIONS, ME2 BACKUP BAR KIT
LIFT CORPORATION Sht. 1 of 16 DSG# M-16-27 Rev. A Date: 03/03/17 INSTRUCTIONS, ME2 BACKUP BAR KIT KIT P/N 296845-01 KIT P/N 296845-01G (GALVANIZED) FORD F-150 (2014-2016), F-250/F-350 (2014 & 2017 MODELS)
Más detallesASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS 3-Shelf Corner Cabinet WHITE ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this
Más detalles3PCS 20 DERECHO. Right. Left
PARTS LIST LISTA DE PARTES 1 2 3 4 CPU Left Panel CPU Right Panel Studs CPU Bottom Panel Panel Izquierdo del porta CPU Panel derecho del porta CPU Patas Panel Inferior del Porta CPU 5 6 7 8 CPU Back Panel
Más detallesCadillac
INSTALLATION INSTRUCTIONS FOR PART 99-2005 APPLICATIONS Cadillac 1996-2005 99-2005 KIT FEATURES IN mount radio provision with pocket ISO mount radio provision with pocket KIT COMPONENTS A) Radio housing
Más detallesEnglish language / Idioma Español AK90-E. Leaflet No. / No. de folleto rev 00
English language / Idioma Español AK90-E Leaflet No. / No. de folleto 466295 rev 00 Read through ALL instructions before commencing installation. If you have any questions about this product or issues
Más detallesFord/Lincoln/Mazda/Mercury
INSTALLATION INSTRUCTIONS FOR PART 99-5600 APPLICATIONS Ford/Lincoln/Mazda/Mercury 1995-2011 99-5600 KIT FEATURES Shaft and DIN unit provision Equalizer provision Rear support provision KIT COMPONENTS
Más detallesMazda MX-5 Miata B
INSTALLATION INSTRUCTIONS FOR PART 99-7519B APPLICATIONS Mazda MX-5 Miata 2009-2010 99-7519B KIT FEATURES DIN Head Unit Provision with pocket ISO DIN Head Unit Provision with pocket Double DIN Head Unit
Más detallesRetrofit Brake Activation Assembly on Empath Recliner
Retrofit Brake Activation Assembly on Empath Recliner 1/8 & 5/32 ALLEN WRENCH 3/8 & 7/16 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
Más detallesOVAL DOOR MEDICINE CABINET BOTIQUÍN CON PUERTA OVALADA
OVAL DOOR MEDICINE CABINET BOTIQUÍN CON PUERTA OVALADA INSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN UNPACKING Care should be taken when you unpack your medicine cabinet. DESEMPACAR Debe tener
Más detallesMANUAL DE INSTRUCCIONES INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES INSTRUCTION MANUAL CPS-RG3-2G11 ES Sustitución de Tubos Fluorescentes 2G11 por Tubos LED 2G11 EN Replacing 2G11 Fluorescent Tubes With 2G11 LED Tubes 1 ES - En las instalaciones
Más detallesWall Mounted Range Hood System
These instructions should not be faxed or reproduced on a digital copier. American Woodmark Corporation provides these instructions on an AS IS basis and disclaims any and all liability for any inaccuracies,
Más detallesHeavy-Duty Air Filter Kit for TRX Trenchers Model No Removing the Existing Air Cleaner. Loose Parts. No Parts Required.
Heavy-Duty Air Filter Kit for TRX Trenchers Model No. 115-09 Form No. 60-5 Rev A Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. Use
Más detalles1200 A Lug Landing Pad Kit EZM1200ULL Kit de área terminal de conexión de las zapatas de A EZM1200ULL
Instruction Bulletin Boletín de instrucciones 73293-777-01 11/2011 1200 A Lug Landing Pad Kit EZM1200ULL Kit de área terminal de conexión de las zapatas de 1 200 A EZM1200ULL Retain for future use. / Conservar
Más detallesMODEL: / MODELO: BATHROOM CABINET MUEBLE DE BAÑO
MODEL: 227 / MODELO: 227 BATHROOM CABINET MUEBLE DE BAÑO NO A B C D E F G H 2 3 PARTS AND HARDWARE LISTA DE PARTES Y HARDWARE RIGHT FRAME MARCO DERECHO LEFT FRAME MARCO IZQUIERDO TOP PANEL PANEL SUPERIOR
Más detallesADULT ASSEMBLY REQUIRED
HORIZONTAL BOOKCASE White Espresso Gray ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small
Más detallesLow Ambient Conversion For LG Single and Flex Multi Inverters
Low Ambient Conversion For LG Single and Flex Multi Inverters LG Electronics Canada Inc. Mississauga, ON L4Z 4G3 01/2012 (866) 543-8324 Model Components Side/Back Front Control LAU090HSV PAG-HS3 Wind Kit
Más detallesINSTRUCCIONES DE ENSAMBLAJE.
English MULTI-FUNCTIONAL COMPUTER TALE ASSEMLY INSTRUCTION MODEL RTA - 2706A IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents
Más detallesChevrolet/Pontiac
INSTALLATION INSTRUCTIONS FOR PART 99-3306 APPLICATIONS Chevrolet/Pontiac 2007-2010 99-3306 KIT FEATURES DIN mount radio provision with pocket ISO mount radio provision with pocket Double DIN mount radio
Más detallesFord Focus 2012-up (w/o Ford My Touch) B
INSTALLATION INSTRUCTIONS FOR PART 99-5827B APPLICATIONS Ford Focus 2012-up (w/o Ford My Touch) 99-5827B KIT FEATURES ISO DIN head unit provision with pocket DDIN head unit provisions Painted Matte Black
Más detallesCHANDELIER Instruction Manual Please read carefully and save these instructions, as you may need them at a later date.
CHANDELIER Instruction Manual Please read carefully and save these instructions, as you may need them at a later date. SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF;
Más detallesCABLE MOUNT INSTRUCTIONS FOR CYLINDERS
CABLE MOUNT INSTRUCTIONS FOR CYLINDERS! CAUTION: Risk of Fire or Electric Shock LED Surface, Pendant & Cable Mounted Cylinder installation requires knowledge of luminaires electrical systems. If not qualified,
Más detallesDoor Stop Kit, 316 SS Compas de porte, 316 SS Tope para puerta, 316 SS
Door Stop Kit, 316 SS Compas de porte, 316 SS Tope para puerta, 316 SS Rev. E 2018 Hoffman Enclosures Inc. PH 763 422 2211 nvent.com/hoffman P/N 87798474 87798663 NOTE: Door stop kit is not intended for
Más detallesMULTI-FUNCTIONAL COMPUTER TABLE
English MULTI-FUNCTIONAL COMPUTER TABLE ASSEMBLY INSTRUCTION IMPORTANT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not use solvents over surfaces
Más detallesConjunto de lámparas con pantalla de vidrio tradicional
Conjunto de lámparas con pantalla de vidrio tradicional Manual de instalación Modelos 99164, 99165, 99166 Compatible con: 2xxxx tipos A - Z Ventiladores serie 51000-58999 Ventiladores serie 59500-59999
Más detallesFord/Mercury
INSTALLATION INSTRUCTIONS FOR PART 99-5720 APPLICATIONS Ford/Mercury 2004-2007 99-5720 KIT FEATURES DIN head unit provisions Various mounting depth alternative Incorporates factory climate controls into
Más detallesIncluded Mounting Hardware
User s Manual Support up to lbs / 0 kg SH-PRO00 Included Mounting Hardware Sliding plate (x) Shelf bracket (x) Hook bracket (x) Connector block (x) M nut (x) Socket head bolt (x) 7 Set screw (x) 8 Grommit
Más detallesNissan Altima 2007-up
INSTALLATION INSTRUCTIONS FOR PART 99-7423 APPLICATIONS Nissan Altima 2007-up 99-7423 KIT FEATURES DIN radio provision with pocket ISO mount radio provision with pocket Double DIN radio provision Stacked
Más detallesMitsubishi Endeavor 2004-up
INSTALLATION INSTRUCTIONS FOR PART 99-7009 APPLICATIONS Mitsubishi Endeavor 2004-up 99-7009 KIT FEATURES DIN head unit provisions SO DIN head unit provisions KIT COMPONENTS A) Radio housing B) ISO brackets
Más detallesFLEXO MERCURIO INSTRUCCIONES INSTRUCTIONS
FLEXO MERCURIO INSTRUCCIONES INSTRUCTIONS 1 ATENCIÓN! Desconectar la conexión a red antes de ser manipulada y realizar el cambio de producto sólo cuando se haya enfriado la fuente existente. WARNING! Disconnect
Más detallesRAMA Poliamide GONZALO MILÁ, 2000
INSTRUCCIONES DE SEGURIDAD Luminaria para exterior. Las conexiones eléctricas deben realizarse por personal especializado. Antes de empezar las operaciones de montaje: Deje sin tensión eléctrica la red.
Más detallesFLEXO URANO INSTRUCCIONES INSTRUCTIONS
FLEXO URANO INSTRUCCIONES INSTRUCTIONS 1 ATENCIÓN! Desconectar la conexión a red antes de ser manipulada y realizar el cambio de producto sólo cuando se haya enfriado la fuente existente. WARNING! Disconnect
Más detallesUniversal 1 speaker spacer rings (For mounting 6 to 6-3/4 speakers to various locations)
INSTALLATION INSTRUCTIONS FOR PART 82-4301 APPLICATIONS Universal 1 speaker spacer rings (For mounting 6 to 6-3/4 speakers to various locations) 82-4301 KIT FEATURES Provides spacing for aftermarket speaker
Más detallesKia Rondo 2007-2010 99-7329
INSTALLATION INSTRUCTIONS FOR PART 99-7329 APPLICATIONS Kia Rondo 2007-2010 99-7329 KIT FEATURES Recessed DIN mount radio provision with pocket ISO mount radio provision with pocket KIT COMPONENTS A) Radio
Más detallesASSEMBLY DRAWING / SPARE PARTS
ASSEMBLY DRAWING / SPARE PARTS Flush button with Lock Nut C7715-6.4 N7714TL Toilet Lid Flush Valve C7715-6 BSB Kit - C7715-1 Fluidmaster Seal Seal - C7715-2 Fill Valve C7715-7 Ceramic tank Air Tube - C7715-3
Más detallesASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE
ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE 4 PC PATIO CONVERSATION SET JUEGO DE PATIO C/ MESA, 2 SILLAS Y UN SILLÓN 250559R /250559T/250559G PLEASE NOTED / POR FAVOR A TENER EN CUENTA: THIS SET OF
Más detallesRetirar los soportes izquierdo y derecho. Remove left and right supports. Retirar las piezas de plástico y la varilla de acero
Flipper door - Mechanism Puerta retráctil - Mecanismo R Line ssembly Guide Guía de montaje Línea R ll required hardware is included. Please check the contents with your packing slip. Read instructions
Más detallesFord multi-kit
INSTALLATION INSTRUCTIONS FOR PART 95-5026 APPLICATIONS See application list inside Ford multi-kit 2001-2006 95-5026 KIT FEATURES Double DIN head unit provision Stacked ISO DIN head unit provision KIT
Más detallesConjunto de luz con pantalla CFL
Conjunto de luz con pantalla CFL Manual de instalación Modelo 99098, 99099 Compatible con: 2xxxx tipos A - Z Ventiladores serie 51000-58999 Ventiladores serie 59500-59999 Ventiladores Casablanca selectos
Más detallesTWILI T-3345X. Instrucciones / Assembly instructions
TWILI T-3345X 493033451 Suspensión con pantalla encintada de fibra de poliéster. pta para uso exterior. Pendant with a ribbon shade made of polyester fiber. Suitable for outdoor use. 55 LE REOMENDMOS LE
Más detallesMeijer.com A
English MULTI-FUNCTIONL COMPUTER TLE SSEMLY INSTRUCTION Meijer.com C MODEL RT - 350 IMPORTNT: Surfaces must be cleaned with a solution of a smooth soap and water, then cleared with a dry towel. Do not
Más detallesINSTALLATION INSTRUCTIONS
Brix Ratio Check Instructions for ColdFusion and Flavor Overload Units INSTALLATION INSTRUCTIONS Brix Ratio Check Instructions For Coldfusion, Flavorfusion and Flavor Overload Units Kit P/N 629096865 SAFETY
Más detallesUniversal aftermarket speaker installation kit
INSTALLATION INSTRUCTIONS FOR PART 82-4600 APPLICATIONS Universal aftermarket speaker installation kit 82-4600 KIT FEATURES Provides spacing for 6-1/2 aftermarket speaker installation. KIT COMPONENTS A)
Más detallesASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS MODEL RTA - 8336 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.
Más detallesINSTA RAIL. Assembly Instruction
INSTA RAIL Assembly Instruction Local building codes vary. Please consult with your local officials for specific requirements. Los códigos de construcción locales pueden variar. Por favor, consulte con
Más detallesConjunto de luz con brazo recto
Conjunto de luz con brazo recto Owner s Guide and Installation Manual Manual De Propietario English Español Form# 43558-02 20090518 2009 Hunter Fan Co. Bienvenido Su nuevo artefacto de iluminación de techo
Más detallesMitsubishi Mirage 2014-up GHG
INSTALLATION INSTRUCTIONS FOR PART 95-7016GHG KIT FEATURES DDIN radio provision Painted Gloss Gray/Black to match factory APPLICATIONS Mitsubishi Mirage 2014-up 95-7016GHG Table of Contents Dash Disassembly.Mitsubishi
Más detallesFPA405 INSTRUCTION MANUAL. We ll Make It Stress-Free
FPA405 INSTRUCTION MANUAL We ll Make It Stress-Free If you have any questions along the way, just give us a call: 1-888-333-9952 (UK: 0800-056-2853) we re ready to help! IMPORTANT SAFETY INSTRUCTIONS SAVE
Más detallesMazda up B
INSTALLATION INSTRUCTIONS FOR PART 95-7521B APPLICATIONS Mazda 5 2012-up 95-7521B KIT FEATURES Double DIN head unit provision Painted scratch-resistant Matte Black KIT COMPONENTS A) Radio Housing B) Radio
Más detallesHyundai
INSTALLATION INSTRUCTIONS FOR PART 99-7309 APPLICATIONS Hyundai 1995-2006 99-7309 KIT FEATURES DIN radio with pocket provision ISO mount radio with pocket provision KIT COMPONENTS A) Radio housing B) Spacer
Más detalles