LG CE110 Guía del usuario Alguna de los contenidos de este manual puede tener variaciones con el telefono dependiendo del software o de proveedor de servicio. 2007 AT&T Knowledge Ventures. Las empresas subsidiarias y afiliadas de AT&T Inc. proporcionan productos y servicios utilizando la marca de AT&T. LG CE 110 User Guide MMBB0198403(1.0) G LG CE110 User Guide Some of the contents in this manual may differ from your phone depending on the software of the phone or your service provider. 2007 AT&T Knowledge Ventures All rights reserved. Subsidiaries and affiliates of AT&T Inc. provide products and services under the AT&T brand.
Bluetooth QD ID B012819 Copyright 2007 LG Electronics, Inc. ALL RIGHTS RESERVED. All materials used herein, including but not limited to trademarks, service marks, and all other commercially valuable rights, properties and products are owned by and proprietary to LG Electronics, Inc. and may not be reproduced, republished, redistributed or disseminated, either in whole or in part, without the express written permission of LGElectronics, Inc. All other marks are proprietary to their respective owners. Features and specifications are subject to change without prior notice.
LIMITED WARRANTY STATEMENT 1. WHAT THIS WARRANTY COVERS : LG offers you a limited warranty that the enclosed subscriber unit and its enclosed accessories will be free from defects in material and workmanship, according to the following terms and conditions: 1. The limited warranty for the product extends for TWELVE (12) MONTHS beginning on the date of purchase of the product with valid proof of purchase, or absent valid proof of purchase, FIFTEEN (15) MONTHS from date of manufacture as determined by the unit s manufacture date code. 2. The limited warranty extends only to the original purchaser of the product and is not assignable or transferable to any subsequent purchaser/end user. 3. This warranty is good only to the original purchaser of the product during the warranty period as long as it is in the U.S, including Alaska, Hawaii, U.S. Territories and Canada. 4. The external housing and cosmetic parts shall be free of defects at the time of shipment and, therefore, shall not be covered under these limited warranty terms. 5. Upon request from LG, the consumer must provide information to reasonably prove the date of purchase. 6. The customer shall bear the cost of shipping the product to the Customer Service Department of LG. LG shall bear the cost of shipping the product back to the consumer after the completion of service under this limited warranty. 2. WHAT THIS WARRANTY DOES NOT COVER : 1. Defects or damages resulting from use of the product in other than its normal and customary manner. 2. Defects or damages from abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized connections, unauthorized repair, misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of LG, including damage caused by shipping, blown fuses, spills of food or liquid. 3. Breakage or damage to antennas unless caused directly by defects in material or workmanship. 4. That the Customer Service Department at LG was not notified by consumer of the alleged defect or malfunction of the product during the applicable limited warranty period. 5. Products which have had the serial number removed or made illegible. 6. This limited warranty is in lieu of all other warranties, express or implied either in fact or by operations of law, statutory or otherwise, including, but not limited to any implied warranty of marketability or fitness for a particular use. 7. Damage resulting from use of non-lg approved accessories.
8. All plastic surfaces and all other externally exposed parts that are scratched or damaged due to normal customer use. 9. Products operated outside published maximum ratings. 10. Products used or obtained in a rental program. 11. Consumables (such as fuses). 3. WHAT LG WILL DO: LG will, at its sole option, either repair, replace or refund the purchase price of any unit that does not conform to this limited warranty. LG may choose at its option to use functionally equivalent reconditioned, refurbished or new units or parts or any units. In addition, LG will not re-install or back-up any data, applications or software that you have added to your phone. It is therefore recommended that you back-up any such data or information prior to sending the unit to LG to avoid the permanent loss of such information. 4. STATE LAW RIGHTS : No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MARKETABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. LG INFOCOMM INC. SHALL NOT BE LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR INABILITY TO USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MARKETABILITY APPLICABLE TO THIS PRODUCT. Some states do not allow the exclusive of limitation of incidental or consequential damages or limitations on how long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 5. HOW TO GET WARRANTY SERVICE : To obtain warranty service, please call or fax to the following telephone numbers from anywhere in the continental United States: Tel. 1-800-793-8896 or Fax. 1-800-448-4026 Or visit www.lgeservice.com. Correspondence may also be mailed to: LG Electronics MobileComm U.S.A., Inc. 201 James Record Road Huntsville, AL 35824 DO NOT RETURN YOUR PRODUCT TO THE ABOVE ADDRESS. Please call or write for the location of the LG authorized service center nearest you and for the procedures for obtaining warranty claims.
CE110 User Guide
Table of Contents For Your Safety.......................5 Your Phone..........................10 Phone Components.........................10 Your Phone s Features......................11 Display Information.........................12 Getting Started...................... 14 Installing the SmartChip....................14 Charging the Battery........................15 Turning Your Phone On and Off..............16 Access Codes..............................17 General Functions...................18 Making a Call..............................18 Making a Call by Send Key.....................18 Making International Calls.....................18 Ending a Call................................18 Making a Call From the Contacts................18 Adjusting the Volume.......................19 Answering a Call.......................... 19 Using the Speakerphone.......................19 Vibrate Mode (Quick).........................19 Signal Strength..............................20 Entering Text...............................20 2 Selecting Functions and Options......23 In-Call Menu........................24 During a Call...............................24 Making a Second Call.........................24 Swapping Between Two Calls..................24 Answering an Incoming Call....................24 Rejecting an Incoming Call.....................24 Muting the Microphone.......................24 Conference Calls...........................24 Making a Second Call.........................25 Setting Up a Conference Call...................25 Activate the Conference Call on Hold............25 Adding Calls to the Conference Call.............25 Private Call in a Conference Call................25 Ending a Conference Call......................25 Menu Tree..........................26 IM..................................29 Messaging..........................33 New Message.............................33 Text........................................33 Multimedia.................................33 Inbox......................................34 Mobile Email...............................35 Drafts.....................................35 Outbox....................................36 Sent.......................................36 IM........................................36
Voicemail..................................37 Templates................................. 37 Text Templates...............................37 Multimedia Templates........................37 Business Card...............................37 Message Settings..........................38 Text Message...............................38 Multimedia Message.........................38 Voicemail Number............................39 Download Message..........................39 Recent Calls.........................40 Missed Calls...............................40 Dialed Calls................................40 Received Calls.............................40 All Calls...................................40 Call Duration...............................40 Last Call....................................40 Dialed Calls.................................40 Received Calls.............................. 40 All Calls....................................41 Data Information...........................41 Web Data...................................41 Data Call...................................41 Total Data..................................41 MEdia Net...........................42 MEdia Net Home...........................42 Bookmarks................................42 Saved Pages...............................43 Enter URL..................................43 Recent Pages..............................43 Security...................................43 Browser Settings...........................43 Accounts...................................43 Cache Settings..............................44 Cookie Settings..............................44 Show Image.................................44 AT&T Mall..........................45 Shop Tones................................45 Shop Games...............................45 Shop Graphics.............................45 Shop Multimedia...........................45 Shop Applications..........................45 MEdia Net Home...........................45 Games & Apps.......................46 Games & Apps.............................46 Java Accounts.............................46 Information................................47 Check Memory...............................47 Java Version................................47 3
My Stuff.............................48 Games & Apps.............................48 Audio & Ringtones.........................48 Graphics.................................. 48 Video......................................48 Tools......................................48 Alarm Clock.................................48 Calendar....................................49 Notepad....................................49 Calculator...................................50 Tip Calculator................................50 World Clock.................................50 Unit Converter...............................50 Camera & Recordings.......................50 Take Photo..................................50 Record Voice................................51 Other Files.................................51 Address Book.......................53 Contact List................................53 New Contact...............................53 Caller Groups..............................53 Speed Dial List.............................53 Copy All Contacts..........................53 Delete All Contacts.........................54 Service Dial Numbers......................54 My Numbers...............................54 Settings.............................55 Audio & Ringtones.........................55 Display....................................56 Bluetooth..................................56 Date & Time...............................57 Call.......................................58 Security...................................60 Connection................................61 Flight Mode................................61 Check Memory.............................62 Handset Information........................62 Reset Default..............................62 Q&A................................63 Accessories.........................65 Safety Guidelines....................67 Glossary............................85 Index...............................87 4
For Your Safety Important Information This user guide contains important information on the use and operation of this phone. Please read all the information carefully for optimal performance and to prevent any damage to or misuse of the phone. Any changes or modifications not expressly approved in this user guide could void your warranty for this equipment. Before You Start Safety Instructions WARNING! To reduce the possibility of electric shock, do not expose your phone to high humidity areas, such as the bathroom, swimming pool, etc. Always store your phone away from heat. Never store your phone in settings that may expose it to temperatures less than 32 F or greater than 104 F, such as outside during extreme weather conditions or in your car on a hot day. Exposure to excessive cold or heat will result in malfunction, damage and/or catastrophic failure. Be careful when using your phone near other electronic devices. RF emissions from your mobile phone may affect nearby in adequately shielded electronic equipment. You should consult with manufacturers of any personal medical devices such as pacemakers and hearing aides to determine if they are susceptible to interference from your mobile phone. Turn off your phone in a medical facility or at a gas station. Never place your phone in a microwave oven as this will cause the battery to explode. IMPORTANT! Please read the TIA SAFETY INFORMATION on page 67 before using your phone. Safety Information Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this user guide. ] Never use an unapproved battery since this could damage the phone and/or battery and could cause the battery to explode. ] Never place your phone in a microwave oven as it will cause the battery to explode. ] Do not dispose of your battery by fire or with hazardous or flammable materials. 5
For Your Safety ] Make sure that no sharp-edged items come into contact with the battery. There is a risk of this causing a fire. ] Store the battery in a place out of reach of children. ] Be careful that children do not swallow any parts such as rubber plugs (earphone, connection parts of the phone, etc.). This could cause asphyxiation or suffocation. ] Unplug the power cord and charger during lightning storms to avoid electric shock or fire. ] When riding in a car, do not leave your phone or set up the hands-free kit near to the air bag. If wireless equipment is improperly installed and the air bag is activated, you may b seriously injured. ] Do not use a hand-held phone while driving. ] Do not use the phone in areas where its use is prohibited. (For example: aircraft). ] Do not expose the battery charger or adapter to direct sunlight or use it in places with high humidity, such as a bathroom. ] Never store your phone in temperatures less than- 4 F or greater than 122 F. ] Do not use harsh chemicals (such as alcohol, benzene, thinners, etc.) or detergents to clean your phone. There is a risk of this causing a fire. ] Do not drop, strike, or shake your phone severely. Such actions may harm the internal circuit boards of the phone. ] Do not use your phone in high explosive areas as the phone may generate sparks. ] Do not damage the power cord by bending, twisting, pulling, or heating. Do not use the plug if it is loose as it may cause a fire or electric shock. ] Do not place any heavy items on the power cord. Do not allow the power cord to be crimped as it may cause fire or electric shock. ] Do not handle the phone with wet hands while it is being charged. It may cause an electric shock or seriously damage your phone. ] Do not disassemble the phone. ] Do not place or answer calls while charging the phone as it may short-circuit the phone and/or cause electric shock or fire. 6
For Your Safety ] Only use the batteries, antennas, and chargers provided by LG. The warranty will not be applied to products provided by other suppliers. ] Only authorized personnel should service the phone and its accessories. Faulty installation or service may result in accidents and consequently invalidate the warranty. ] Do not hold or let the antenna come in contact with your body during a call. ] An emergency call can be made only within a service area. For an emergency call, make sure that you are within a service area and that the phone is turned on. FCC RF Exposure Information WARNING! Read this information before operating the phone. In August 1996, the Federal Communications (FCC) of he United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. CAUTION Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a minor burn may result. Contact your local dealer for a replacement antenna. Body-worn Operation This device was tested for typical body-worn operations with the back of the phone kept 0.6 inches (1.5cm) between the user s body and the back of the phone. To comply with FCC RF exposure requirements, a minimum separation distance of 0.6 inches(1.5cm) must be maintained between the user's body and the back of the phone. Third-party belt-clips, holsters, and similar accessories containing metallic components should not be used. Bodyworn accessories that cannot maintain 0.6 inches(1.5cm) separation distance between the user's body and the back of the phone, and 7
For Your Safety have not been tested for typical body-worn operations may not comply with FCC RF exposure limits and should be avoided. Vehicle Mounted External Antenna (optional, if available) A minimum separation distance of 8 inches (20cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCC website at www.fcc.gov FCC Part 15 Class B Compliance This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device and its accessories may not cause harmful interference, and (2) this device and its accessories must accept any interference received, including interference that may cause undesired operation. Cautions for Battery ] Do not disassemble. ] Do not short-circuit. ] Do not expose to high temperature: 60 C (140 F).] ] Do not incinerate. Battery Disposal ] Please dispose of your battery properly or bring to your local wireless carrier for recycling. ] Do not dispose in fire or with hazardous or flammable materials. Adapter (Charger) Cautions ] Using the wrong battery charger could damage your phone and void your warranty. ] The adapter or battery charger is intended for indoor use only. Do not expose the adapter or battery charger to direct sunlight or use it in places with high humidity, such as the bathroom. 8
For Your Safety Avoiding hearing damage Permanent hearing loss may occur if you use your phone and/or headset at a high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected. Hearing experts suggest that to protect your hearing: ] Limit the amount of time you use your phone and/or headset at high volume. ] Avoid turning up the volume to block out noisy surroundings. ] Turn the volume down if you can't hear people speaking near you. For information about how to set a maximum volume limit on your phone, see the features guide for your phone. Using your phone safely Use of your phone while operating a vehicle is not recommended and is illegal in some areas. Be careful and attentive while driving. Stop using your phone if you find it disruptive or distracting while operating any type of vehicle or performing any other activity that requires your full attention. 9
Your Phone Phone Components 1. Earpiece 7. Active flip 8. Display screen 2. Left soft key 9. Navigation key 10. Confirmation key 11. Right soft key 3. Side keys 4. Send key 5. Alphanumeric keys 12. Message key 13. Camera key 14. End /Power key 15. Clear key 6. Microphone 10
Your Phone Your Phone s Features 1. Earpiece 2,11. Left soft key/right soft key: Each of these keys perform the functions indicated by the text on the display immediately above them. 3. Side keys: These keys are used to control the volume of ringtone in standby mode and speaker volume during a call. 4. Send key: You can dial a phone number and answer incoming calls. Press this key in standby mode to quickly access the most recent incoming, outgoing and missed calls. 5. Alphanumeric keys: These keys are used to dial a number in standby mode and to enter number or characters in edit mode. 6. Microphone: Can be muted during a call for privacy. 7. Active flip: Open the flip to answer an incoming call and close to end the call. 8. Display screen: Displays phone status icons, menu items, web information, pictures and more in full color. 9. Navigation key: Use for quick access to phone functions. 10. Confirmation key: Short press will launch the WAP browser. Allows you to select and confirm menu options. 12. Message key: Use to retrieve or send text messages. 13. Camera key: Press this key to use the camera feature. Directly goes to the camera mode. 14. End/Power key: Allows you to power the phone on or off, end calls, or return to Standby Mode. 15. Clear key: Allows you to delete the characters entered or return you to the previous screen. 11
Your Phone Camera External display Antenna Side key External Display Your phone has an external display on the cover. It indicates when you have an incoming call or a message. It also alerts you at the specified time when you set an alarm by turning on its backlight and showing corresponding icon on it. Display Information Icon area Backlight A backlight illuminates the display and the keypad. When you press any key or open the folder, the backlight turns on. It turns off if no key is pressed within a given period of time, depending on the Backlight Timer menu option. To specify the length of time the backlight is active, set the Backlight Timer menu option (Menu 9.2.3). 12 Area First line Middle lines Last line Text and graphic area Soft key indications Description Displays various icons. See page 13 Display messages, instructions and any information that you enter, such as number to be dialed. Shows the functions currently assigned to the two soft keys.
Your Phone On-Screen Icons The table below describes various display indicators or icons that appear on the phone s display screen. Icon Description Indicates the strength of the network signal. Indicates that the EDGE service is available. Connection to the EDGE service allows you to transfer data at a speed of 200Kb/s(depending on network availability). Check with your operator for network coverage and service availability. Indicates a call is in progress. Indicates that GPRS service is available. Indicates the alarm has been set and is on. Indicates the status of the battery charge. Indicates the receipt of a text message. Indicates the receipt of a MMS message. Indicates the receipt of a voice mail. Icon Description Indicates that the vibration has been set for alert. Indicates the silent has been set for alert. Indicates Ring has been set for alert. Indicates the speakerphone has been activated. Indicates the Schedule function. Indicates the Bluetooth is On. Indicates the TTY has been set and is on. * The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners. Bluetooth QD ID B012819 13
Getting Started Installing the SmartChip When you subscribe to a cellular network, you are provided with a plug-in SmartChip loaded with your subscription details, such as your PIN, any optional services available and many others. n Important! The plug-in SmartChip and its contacts can be easily damaged by scratches or bending, so be careful when handling, inserting or removing the card. Keep all SmartChips out of the reach of small children. 1. If necessary, switch off the phone by holding down the key until the poweroff image displays. 2. Remove the battery. To do so: 1 Pull and hold the battery lock above the battery toward the top of the phone. ➁ Lift the battery away, as shown. 2 1 4 3. Slide the SmartChip into the SmartChip socket so that it locks the card into place. Make sure that the notched corner is bottom left and the gold contacts of the card face into the phone. 3 14
Getting Started 5. Attach back cover by sliding up into position until it clicks. 4 3 n Note When you need to remove the SmartChip, slide it, as shown, and take it out of the socket. 4. To insert the battery, align the golden contacts of the battery with the corresponding connectors on the battery compartment. Press down on the opposite end of the battery until it snaps into place. 2 1 Charging the Battery Use of unauthorized accessories could damage your phone and void your warranty. To use the travel charger provided with your phone: 1. With the battery in position in the phone, connect the lead from the travel charger to the bottom of the phone. Check that the arrow on the lead connector is facing towards the front of the phone. 2. Connect the travel charger to a standard AC wall outlet. Only use the travel charger that comes with the package. 15
Getting Started n Warning The travel charger must be unplugged before you remove the battery, otherwise, the phone could the damaged. 3. When charging is finished, disconnect the travel charger from the phone by pressing on the gray tabs on both sides of the connector while pulling the connector out. Turning Your Phone On and Off 1. Press the [END] key to swith on the phone. 2. If the phone asks for a PIN, enter the PIN and press the key. The phone searches for your network and after finding it goes to the idle screen as illustrated below. From the idle screen, you can make or receive a call. n Note ] If your phone is powered on while charging, you ll see the bars in the battery indicator icon cycle. When the battery is fully charged, the bars in the battery indicator icon will flash on and off. If the battery fails to charge completely: ] After turning the phone on and off, please attempt to recharge the battery. ] After detaching and reattaching the battery, please attempt to recharge the battery. n Note The display language is preset to Automatic at the factory. To change the language, use the Languages menu option (Menu 9.2.6). 3. When you wish to switch the phone off, hold down the [END] key until the power-off image displays. 16
Getting Started Access Codes You can use the access codes described in this section to avoid unauthorized use of your phone. The access codes can be changed by using the Change Codes feature (Menu 9.6.3). Security code (4 digits) The security code protects the unauthorized use of your phone. The default security code is set to 0000 and the security code is required to delete all phone entries and to activate the Restore Factory Settings menu. The security code default setting can be modified from the Security Settings menu. 17
General Functions Making a Call 1. Make sure your phone is powered on. 2. Enter a phone number including the area code. To edit a number on the display screen, simply press the key to erase one digit at a time. ] Press and hold the key to erase the entire number. 3. Press the [SEND] key to call the number. 4. When finished, press the [END] key. Making a Call by Send Key 1. Press the [SEND] key, and the most recent incoming, outgoing and missed phone numbers will be displayed. 2. Select the desired number by using the navigation key. 3. Press the [SEND] key. Making International Calls 1. Press and hold the key and the international access character + will appear. 2. Enter the country code, area code, and the phone number. 3. Press the [SEND] key. Ending a Call When you have finished a call, press the [END] key. Making a Call From the Contacts You can store names and phone numbers dialed frequently in the SmartChip as well as in the phone memory known as the Contacts. You can dial a number by simply selecting a name in the contacts and pressing the [SEND] key. 18
General Functions Adjusting the Volume During a call, if you want to adjust the earpiece volume, use the side keys of the phone. In idle mode, you can adjust the ring volume using the side keys. Answering a Call When you receive a call, the phone rings and the flashing phone icon appears on the screen. If the caller can be identified, the caller s phone number (or name if stored in your Address Book) is displayed. 1. Open the Flip and press the [SEND] key or the left soft key to answer an incoming call. If Any Key has been set as the answer mode (Menu 9.5.4), any key press will answer a call except for the [END] key or the right soft key. n Note ] To reject an incoming call, press and hold the side keys on the left side of the phone. ] If Open Flip has been set as the Answer Mode (Menu 9.5.4), you do not need to press any key. You can answer the call simply by opening the flip. 2. End the call by closing the phone or pressing the [END] key. n Notice You can answer a call while using the Address Book or other menu features. Using the Speakerphone You can use the integrated Speakerphone during a call by pressing the right soft key [Options] then select Speaker On. The speakerphone indicator [ ] will display on the display screen. The loudspeaker is automatically deactivated when you end the call. n Warning Due to higher volume levels, don t place the phone near your ear while the speakerphone is enabled. Vibrate Mode (Quick) Vibrate Mode can be activated by pressing and holding down the [Star] key. 19
General Functions Signal Strength If you are inside a building, being near a window may give you better reception. You can see the strength of your signal by the signal indicator on your phone s display screen. Entering Text You can enter alphanumeric characters by using the phone s keypad. For example, storing names in the Address Book, writing a message, or creating scheduling events in the calendar all require entering text. The following text input methods are available in the phone. T9 Mode This mode allows you to enter words with only one keystroke per letter. Each key on the keypad has more than one letter. The T9 mode automatically compares your keystrokes with an internal linguistic dictionary to determine the correct word, thus requiring far fewer keystrokes than the traditional ABC mode. ABC Mode This mode allows you to enter letters by pressing the key labeled with the required letter once, twice, three or four times until the letter is displayed. 123 Mode (Numbers Mode) Type numbers using one keystroke per number. To change to 123 mode in a text entry field, press key until 123 mode is displayed. A long press changes the mode to 123. Symbolic Mode This mode allows you to enter special characters. n Note You can select a different T9 language from the menu option. The default setting on the phone is T9 disabled mode. Changing the Text Input Mode Change the text input mode by pressing. You can check the current text input mode in the upper right corner of the screen. 20
General Functions Using the T9 Mode The T9 predictive text input mode allows you to enter words easily with a minimum number of key presses. As you press each key, the phone begins to display the characters that it thinks you are typing based on a built-in dictionary. As new letters are added, the word changes to reflect the most likely candidate from the dictionary. 1. When you are in the T9 predictive text input mode, start entering a word by pressing keys to. Press one key per letter. ] The word changes as letters are typed - ignore what s on the screen until the word is typed completely. ] If the word is still incorrect after typing completely, press thethe up/down navigation keys once or more to cycle through the other word options. ] If the desired word is missing from the word choices list, add it by using the abc/abc mode. 2. Enter the whole word before editing or deleting any keystrokes. 3. Complete each word with a space by pressing the key or the right navigation key. To delete letters, press. Press and hold down to erase the letters continuously. Continue hoding to erase entire words. Using the ABC Mode Use the keypad keys to enter your text. 1. Press the key labeled with the required letter: ] Once for the first letter ] Twice for the second letter ] And so on 2. To insert a space, press the key once. To delete letters, press the key. Press and hold down the key to erase the letters continuously. n Note Refer to the table below for more information on the characters available using the keys. 21
General Functions Key Characters in the Order Display Upper Case Lower Case 1., -?! ' @ : 1., -?! ' @ : 1 2 A B C 2 a b c 2 3 D E F 3 d e f 3 4 G H I 4 g h i 4 5 J K L 5 j k l 5 6 M N O 6 m n o 6 7 P Q R S 7 p q r s 7 8 T U V 8 t u v 8 9 W X Y Z 9 w x y z 9 0 Space Key, 0 (Long press) Space Key, 0 (Long press) Using the 123 (Numbers) Mode The 123 Mode enables you to enter numbers in a text message (a telephone number, for example) more quickly. Press the keys corresponding to the required digits before manually switching back to the appropriate text entry mode. Using the Symbol Mode The Symbol Mode enables you to enter various symbols or special characters. To enter a symbol, press the [Star] key. Use the navigation keys to select the desired symbol and press the [OK] key. 22
Selecting Functions and Options Your phone offers a set of functions that allow you to customize the phone. These functions are arranged in menus and sub-menus, accessed via the two soft keys marked the left soft key and the right soft key. Each menu and sub-menu allows you to view and alter the settings of a particular function. The soft key functions vary depending on the mode of the phone. The label on the bottom of the display screen immediately above the soft keys indicates current function. Press the left soft key to access the available Menu. Press the right soft key to access the available Options. Short press will launch the WAP browser (In standby mode). Short press allows you to select and confirm menu options. 23
In-Call Menu Your phone provides a number of control functions that you can use during a call. To access these functions during a call, press the right soft key [Options]. During a Call The menu displayed on the handset screen during a call is different than the default main menu displayed when in idle screen, and the options are described below. Making a Second Call You can select a number you wish to dial from the Address Book to make a second call. Press the right soft key then select Contacts. Swapping Between Two Calls To switch between two calls, press the right soft key, and then select Swap or press the [SEND] key. Answering an Incoming Call To answer an incoming call when the handset is ringing, simply press the [SEND] key. The handset is also able to warn you of an incoming call while you are already on a call. A tone sounds in the earpiece, and the display 24 will show that a second call is waiting. This feature, known as Call Waiting, is only available if your network supports it. If Call Waiting is on, you can put the first call on hold and answer the second call, by pressing the [SEND] key. Rejecting an Incoming Call You can reject an incoming call without answering by simply pressing the [END] key. During a call, you can reject an incoming call by pressing the [END] key. Muting the Microphone You can mute the microphone during a call by pressing the left soft key [Mute]. The handset can be unmuted by pressing the left soft key [Unmute]. When the handset is muted, the caller cannot hear you, but you can still hear the caller. Conference Calls The conference service provides you with the ability to have a simultaneous conversation with more than one caller. The conference call feature can be used only if your network
In-Call Menu service provider supports this feature. The conference call can only be set up when you have one call active and one call on hold, meaning both calls must have been answered. Once a conference call is set up, calls may be added, disconnected or separated (that is, removed from the conference call but still connected to you) by the person who set up the conference call. These options are all available from the In-Call menu. The maximum number of callers in a conference call is five. Once started, you are in control of the conference call, and only you can add calls to the conference call. Making a Second Call You can make a second call while currently on a call simply by entering the second number and pressing the [SEND] key. When the second call is connected, the first call is automatically placed on hold. You can swap between calls, by pressing the [SEND] key. Setting Up a Conference Call To set up a conference call, place one call on hold, conference in the second active call by pressing the right soft key and select the Join Calls sub menu option from the Conference Call menu. Activate the Conference Call on Hold To activate a conference call on hold, press the [SEND] key. Adding Calls to the Conference Call To add a call to an existing conference call, press the right soft key, and then select the Join Calls sub menu from the Conference Call option. Private Call in a Conference Call To have a private call with one caller from a conference call, press the right soft key and select the Private Menu from the Conference Call option. When the numbers of the callers are displayed, select the one you wish to speak in private. Ending a Conference Call Currently active conference call can be disconnected by pressing the [END] key. 25
Menu Tree The following illustration shows the available menu structure and indicates the: ] Number assigned to each menu option. ] Page where you can find the feature description. 1. IM (see page 29) 2. Messaging (see page 33) 2.1 New Message 2.1.1 Text 2.1.2 Multimedia 2.2 Inbox 2.3 Mobile Email 2.4 Drafts 2.5 Outbox 2.6 Sent 2.7 IM 2.8 Voicemail 2.9 Templates 2.9.1 Text Templates 2.9.2 Multimedia Templates 2.9.3 Business Card 2.0 Message Settings 2.0.1 Text Message 2.0.2 Multimedia Message 2.0.3 Voicemail Number 2.0.4 Download Message 26 3. Recent Calls (see page 40) 3.1 Missed Calls 3.2 Dialed Calls 3.3 Received Calls 3.4 All Calls 3.5 Call Duration 3.5.1 Last Call 3.5.2 Dialed Calls 3.5.3 Received Calls 3.5.4 All Calls 3.6 Data Information 3.6.1 Web Data 3.6.2 Data Call 3.6.3 Total Data
Menu Tree 4. MEdia Net (see page 42) 4.1 MEdia Net Home 4.2 Bookmarks 4.3 Saved Pages 4.4 Enter URL 4.5 Recent Pages 4.6 Security 4.7 Browser Settings 4.7.1 Accounts 4.7.2 Cache Settings 4.7.3 Cookie Settings 4.7.4 Show Image 5. AT&T Mall (see page 45) 5.1 Shop Tones 5.2 Shop Games 5.3 Shop Graphics 5.4 Shop Multimedia 5.5 Shop Applications 5.6 MEdia Net Home 6. Games & Apps (see page 46) 6.1 Games & Apps 6.2 Java Accounts 6.3 Information 6.3.1 Check Memory 6.3.2 Java Version 7. My Stuff (see page 48) 7.1 Games & Apps 7.2 Audio & Ringtones 7.3 Graphics 7.4 Video 7.5 Tools 7.5.1 Alarm Clock 7.5.2 Calendar 7.5.3 Notepad 7.5.4 Calculator 7.5.5 Tip Calculator 7.5.6 World Clock 7.5.7 Unit Converter 7.6 Camera & Recordings 7.6.1 Take Photo 7.6.2 Record Voice 7.7 Other Files 8. Address Book (see page 53) 8.1 Contact List 8.2 New Contact 8.3 Caller Groups 8.4 Speed Dial List 8.5 Copy All Contacts 8.6 Delete All Contacts 8.7 Service Dial Numbers 8.8 My Numbers 27
Menu Tree 9. Settings (see page 55) 9.1 Audio & Ringtones 9.1.1 Shop Tones 9.1.2 Ringtones 9.1.3 Volume 9.1.4 Message Alert Tones 9.1.5 Alert Type 9.1.6 Increasing Ringtone 9.1.7 Power On/Off Tones 9.2 Display 9.2.1 Shop Graphics 9.2.2 Wallpapers 9.2.3 Backlight Timer 9.2.4 Brightness 9.2.5 Menu Styles 9.2.6 Languages 9.3 Bluetooth 9.3.1 Bluetooth On/Off 9.3.2 Device List 9.3.3 Bluetooth Settings 9.4 Date & Time 9.4.1 Set Date 9.4.2 Date Format 9.4.3 Set Time 9.4.4 Time Format 9.4.5 Auto Update 28 9. Settings (continued) 9.5 Call 9.5.1 Call Forwarding 9.5.2 Send My Number 9.5.3 Auto Redial 9.5.4 Answer Mode 9.5.5 Minute Minder 9.5.6 Call Waiting 9.5.7 TTY 9.5.8 Send DTMF Tones 9.5.9 Hearing Aid 9.6 Security 9.6.1 PIN Code Request 9.6.2 Fixed Dial Number 9.6.3 Change Codes 9.7 Connection 9.7.1 GPRS Attach 9.7.2 Network Profile 9.7.3 Reset Network Profile 9.8 Flight Mode 9.9 Check Memory 9.9.1 Common 9.9.2 Reserved 9.9.3 SmartChip 9.0 Handset Information 9.* Reset Default
IM The Instant Messaging feature can only be used with the support of the network operator or communities such as AIM, Windows Live Messenger, Y! Messenger. For Instant Messaging users, a valid User ID and Password will be required in order to login and exchange messages as well as checking the online status. There are two ways to use the Instant Messaging feature. 1. Through the Main Menu. 2. Through the IM hotkey (the right navigation key). Short pressing the hotkey will bring up the available IM clients. The menu items below might not appear since not all IM communities support the various options. Also the menu strings may appear differently based on the selected IM communities. The keywords such as User ID, Login and Contact will be used as general terms in IM menus according to the currently selected communities such as AIM, Windows Live Messenger, Y! Messenger. Offline Menu Sign In This allows users to login by filling in the User ID and Password. n Note If your phone number is not registered on the SmartChip you will not be able to log into the IM client You can check your phone number in the My numbers menu (Menu 8.8) n Note Once the User ID and Password are saved, you will not be required to type them in again during the Login process. This feature is optional. Saved Conversations This is where a user can view saved conversations. Settings ] Save Passwaord: You can save your password in login Input. ] Power - on Sing In: If you set the desired IM community that saved your ID and Password, you will be automatically login to the community when you switch the phone on. IM Information This indicates the Instant Messaging Client Information such as Client Name and Version Number. 29
IM Online Menu / 1 to 1 conversation After successful Login, a list of contacts with Screen Names will appear on screen. Depending on the cursor location in the contacts, the menu options will be available. When cursor is located on a Conversations List n Note The Converations List contains both the active contact where a conversation has taken place as well as unknown contact. ] View/Hide Conversation: This provides the option to view or hide contacts from the selected list. n Note When you select the left/right navigation key or the Confirm key on the Conversations List, it offers the ability to view or hide conversations. ] Send to Others: This offers the ability to send a message to an unknown contact. When selected, User ID must be typed in prior to starting an IM session or conversation. ] Saved Conversations: You may view or delete the stored conversation session. ] Settings My Status: Allows you to set your status to Available, Busy or Invisible. Show Offline Contacts: You have the ability to show all contacts or only online contacts while in Y! Messenger service. Display Name: You may change your display name to be used while in Windows Live Messenger service. ] Log Out: This begins the Logout process. When the cursor is located on a Conversation ] End Conversation: This closes the selected conversation. If an unknown contact was selected, that contact is deleted. ] Block/Unblock Contact: This allows you to block/unblock the selected Conversations Contact. ] View Information: This allows you to view the User ID and Status Text information. ] Refresh Contact: This refreshes the presence information of the selected contact. 30
IM ] Settings: Please refer to the previous Settings Menu. ] Log Out: This begins the Logout process. When the cursor is located on a Contact List ] View/Hide Conversations: This provides the option to view or hide contacts from selected list. ] Add Contact: This adds a new contact to the selected contacts list, in the meantime this searches for the contact on the basis of E-mail Address, First Name, or Last Name. ] Blocked List: This allows you to view the blocked list. ] Refresh List: This refreshes the presence information of the contacts within the contacts. ] Send to Others: This offers the ability to send a message to an unknown contact. When selected, the User ID must be typed in prior to starting an IM session or conversation. ] Settings: Please refer to the previous Settings Menu. ] Logout: This begins the Logout process. When the cursor is located on a Contact ] Add Contact: This adds a new contact to the selected contacts list; in the meantime this searches for the contact on the basis of E-mail Address, First Name, or Last Name. ] Delete Contact: This deletes the selected Contact. ] Block/Unblock Contact: This allows or blocks conversation with the selected Contact. ] Refresh Contact: This refreshes the presence information of the selected contact. ] View Information: This allows you to view information. It provides User ID, Status Text. ] Settings: Please refer to the previous Settings Menu. ] Logout: This begins the Logout process. 31
IM Menu options available in the Conversation screen ] Send: This allows you to send the typed message. ] Back To List: This brings the screen back to the contacts. ] Insert: You can insert Symbol, Template and emoticons in the conversation screen. ] Block/Unblock Contact: This allows or blocks conversation with the selected Contact. ] Save Conversation: Stores currently active conversation. ] End Conversation: This ends the active conversation and clears the conversation buffer. ] View Information: This allows you to view the User ID and Status Text information. ] Set T9: This selects the T9 predictive mode Language. In the conversation window, you can use the up/down navigation key for scrolling through the conversation. Maximum number of characters supported by a message is 400 characters for receiving and 128 characters for sending. The presence information might not update in real time so the Refresh List / Refresh Contact option can be used for most up to date status. n Note Within the conversation screen, you can insert symbols, emoticons and text templates by using the left soft key. 32
Messaging New Message Menu 2.1 Text (Menu 2.1.1) You can write and edit text messages of up to 918 characters. 1. Type in a message using key presses. For details on how to enter text, refer to page 20 (Entering Text). 2. After completing the message select the required option by pressing the right soft key [Options]. The following options are available. ] Insert Symbol: Attach special characters. Picture: Send and receive text messages that contain pictures, known as Enhanced Messaging Service. Several preset pictures are available in the phone and they can be replaced with new ones received from other sources. Animation: Attaching an animation in a message can be done through EMS(Enhanced Messaging Service). Audio: Attach sounds that are available for short message. Text Template: Use the text templates already set in the phone. Contact: Attach a phone number. Business Card: Attach your name card. ] Save to Drafts: Save the message so that it can be sent later. ] T9 Languages: Choose between English or Spanish T9 language. For details on how to enter text, refer to page 21 (Using the T9 Mode). ] Clear Text: Deletes the written message. ] Cancel: Exit the text editor. Press the left soft key [Send To]. ] Send To: Enter the phone number or select the number from the address book. Multimedia (Menu 2.1.2) You can write and edit multimedia messages, checking message size. You can create a new message or choose one of the multimedia message templates already made. Press the left soft key [Send To]. ] Send To: You can send multimedia messages to multiple recipients, prioritize your message, and make it sent later as well. 33
Messaging Press the right soft key [Options]. The following options are available. ] Insert: Symbol, Graphic, Audio, Video, New Photo, New Audio, Template, Contact, Business Card, vcard or vcalendar. ] New Slide: You can insert a slide and place it to Insert Slide Before or Insert Slide After. ] Preview: You can preview multimedia messages you wrote. ] Save: You can save multimedia messages To Drafts or As Template. ] Set Duration: You can set timer for slide. ] T9 Languages: Choose between English or Spanish T9 language. For details on how to enter text, refer to page 21 (Using the T9 Mode). ] Cancel: You can back to the Message menu. n Note If you select the photo on writing multimedia message, loading duration will take about 5 seconds. At that time, you can t activate any key during loading time. After that time, it is available to write multimedia message. Inbox Menu 2.2 You will be alerted when you receive a message. They will be stored in the Inbox. In the Inbox, you can identify each message by icons. If you are notified that you have received a multimedia message, you can download the whole multimedia message by selecting it in the Receive menu. The following [Options] are available in the Inbox list. ] Delete: You can delete the current message. ] Reply: You can reply to the sender. ] Forward: You can forward the selected message to another party. ] Return Call: Call back the sender. ] Information: You can view information about received messages. ] Delete all Read: You can delete all read messages. ] Delete All: You can delete all messages. 34