IntesisBox Modbus Server - Mitsubishi Electric G50

Transcripción

1 IntesisBox Server - Mitsubishi Electric G50 Gateway for monitor and control Mitsubishi Electric City Multi Air Conditioning systems from any master device TCP or RTU (BMS, PLC, SCADA, HMI, TouchPanel ) Master TCP LinkBoxMB Configuration Software Master RTU RTU RS232/RS485 RS232 IntesisBox Only needed for configuration Ethernet TCP LAN / WAN XML G50 G50 Mitsubishi Electric City Multi Mitsubishi Electric City Multi This integration requires the Mitsubishi Electric City Multi AC system be equipped with the Mitsubishi Electric G-50A, GB-50A o AG-150A gateway This gateway from Mitsubishi Electric offers the signals of the City Multi AC system through XML protocol Every G50 (G-50A, GB-50A, AG-150A or AE200) allows access to the signals of up to 50 City Multi internal units and 50 groups, no matter the number of external units installed In the G50, the group is the control unit, every group can have from 1 to 16 associated internal units This integration supervises and control groups, not internal units, although if only one internal unit is associated to every group then you can supervise and control internal units individually This G50 gateway is supplied by Mitsubishi Electric Contact your nearest Mitsubishi Electric distributor for details IntesisBox can talk to up to 2 Mitsubishi Electric G50s using XML protocol, and offers the signals of all these City Multi groups through its slave interface, each signal in a predefined fixed address The AG-150A can be used with Expansions Cards as explained in the section IntesisBox capacity The interface of IntesisBox can be freely configured as RTU RS232, RTU RS485 or TCP The commissioning of IntesisBox is almost plug & play, only IP parameters of the box and of G50s have to be configured using LinkBoxMB, a friendly software configuration tool for Windows TM supplied along with IntesisBox with no additional cost TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 1 / 11

2 1 IntesisBox capacity Element Max Notes Num of G50 2 Number of independent G50 interfaces 2 x G-50A / GB-50A / AE200 2 x AG150 / AE200 (without Expansion Controllers) 1 x AG150 / AE200 (with 2 Expansion Controllers) Number of City Multi groups: (Number of G50s X 50) 100 Maximum number of groups Number of variables per group 19 addresses Number of variables per G addresses Maximum number of variables 1902 addresses There are 2 different models of IntesisBox server - Mitsubishi Electric G50 with different capacity every one of them The table above shows the capacity for the top model (with maximum capacity) The 2 different models allow integrating respectively: 1 or 2 G50s And their order codes are: ME-AC-MBS-50 Model supporting up to 1 G50 / AE 200 and 50 City Multi groups ME-AC-MBS-100 Model supporting up to 2 G50s / AE200 and 100 City Multi groups! NOTE: Please, remember that Mitsubishi Electric AG-150A requires a software license, PC-Monitoring license (SW-Mon), that has to be purchased together with the AG-150A gateway TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 2 / 11

3 2 Sample applications Integration of Mitsubishi Electric City Multi Air Conditioning systems equipped with the interface G50 into control systems Master TCP Master RTU RTU RS232/RS485 IntesisBox Ethernet TCP LAN / WAN XML G50 G50 Mitsubishi Electric City Multi Mitsubishi Electric City Multi Control system with master interface: BMS SCADA PLC DDC Home Automation AMX, Crestron Typical Mitsubishi Electric Air Conditioning systems equipped with G50 interface: City Multi model G-50A (version of G50 with display and keypad), GB-50A (version of G50 with blind cover), and AG-150A (new version of G50 with touch-display) are all supported, no difference from IntesisBox's point of view 50 City Multi indoor units or 50 groups per G50 Every group can have from 1 to 16 associated indoor units MODBUS Full supervision and control System supervising / controlling System under supervision / control TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 3 / 11

4 3 Typical applications Integration of Mitsubishi Electric Air Conditioning into systems For this application, Mitsubishi Air Conditioning system must be equipped with G-50A, GB-50A or AG-150A Gateway For more information about these devices contact Mitsubishi Electric Indoor units Outdoor unit Bus M-Net G-50A, GB-50A or AG-150A (with XML option) Ethernet (crossed cable) network IntesisBox Master TCP / RTU ME-AC-MBS-50 TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 4 / 11

5 4 interface General Max Number of Up to two G50s can be supported Mitsubishi ElecG50s Virtual signals One communication error virtual signal per every G50 device defined One communication error virtual signal per every group into the G50 device One virtual signal per every group into the G50 device to enable/disable this group in the polling process All these virtual signals can be read/written from interface Device type Slave modes TCP, RTU RS232 or RS485 supported TCP IP address configuration Subnet mask parameters Default gateway address TCP port RTU RS232/RS485 configuration Baud rate parameters Parity Slave number Points Configuration No point configuration needs to be done, all the Mitsubishi Electric G50 signals are automatically associated to predefined fixed Addresses function Read functions: codes supported 3- Read holding registers 4- Read input registers Write functions: 6- Write single register 16- Write multiple registers If poll records are used to read/write multiple records, the range of addresses requested must contain valid addresses, if not the corresponding error code will be responded data coding All the point's values are coded in 2 bytes registers (even if their possible values are 0 and 1) and expressed in MSBLSB TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 5 / 11

6 41 Extract of the predefined address table Address G50 Group Property G50 Group Property Address Error Com G Error Com G Drive Drive Mode Mode SetTemp SetTemp AirDirection AirDirection FanSpeed FanSpeed RemoCon RemoCon DriveItem DriveItem ModeItem ModeItem SetTempItem SetTempItem FilterItem FilterItem Ventilation Ventilation FilterSign FilterSign ErrorSign ErrorSign InletTemp InletTemp FilterSignReset FilterSignReset ErrorSignReset ErrorSignReset Error Com Group Error Com Group Polling Active Polling Active G50 Group Property G50 Group Property Address Address Drive Drive Mode Mode SetTemp SetTemp AirDirection AirDirection FanSpeed FanSpeed RemoCon RemoCon DriveItem DriveItem ModeItem ModeItem SetTempItem SetTempItem FilterItem FilterItem Ventilation Ventilation FilterSign FilterSign ErrorSign ErrorSign InletTemp InletTemp FilterSignReset FilterSignReset ErrorSignReset ErrorSignReset Error Com Group Error Com Group Polling Active Polling Active There are also a series of signals that indicate an Alarm Code in any of the devices present in the M-Net Mitsubishi network To obtain the address, you must apply following formula: ADRESS MODBUS = ( (NumbG50x1000)) + M-Net Add where M-Net Add is 0 for the G50 device, 1 to 50 for Indoor Units, 51 to 100 for Outdoor Unit, 101 to 200 for Remote Controllers and 200 to 250 for System Controllers For more information contact Mitsubishi Electric TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 6 / 11

7 5 Mitsubishi Electric G50 interface Mitsubishi Electric G50 interface Device type Configuration Parameters Client Polling interval (1600 seconds) Per every G50 defined: Descriptive name IP address TCP port TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 7 / 11

8 51 Signals available per every Mitsubishi Electric City Multi AC indoor unit or group of indoor units Property Drive Mode 1 SetTemp 1 AirDirection FanSpeed RemoCon DriveItem ModeItem SetTempItem FilterItem Ventilation FilterSign ErrorSign InletTemp G50 Communication Error Group Communication Error Polling Active Alarm Code Description / Status Start/Stop Read/Write: ON, OFF AC Mode Read/Write: COOL, DRY, FUN, HEAT, AUTO, HEAT RECOVERY, LC_AUTO, BYPASS Read: AUTO HEAT, AUTO COOL Temperature Set Point (only integer numbers allowed) Read/Write: For COOL or DRY mode:1930 ºC, for HEAT mode: 1728 ºC, for AUTO mode:1928 ºC) Air output direction Read/Write: HORIZONTAL, MID1, MID2, VERTICAL, SWING AC fan speed or LOSSNAY Read/Write: HIGH, MIDH, MIDL, LOW Prohibition for General control from the local panel Read/Write: PROHIBIT, PERMIT Prohibition for ON/OFF control from the local panel Read/Write: CHK_ON, CHK_OFF Prohibition for Mode control from the local panel Read/Write: CHK_ON, CHK_OFF Prohibition for Set Point control from the local panel Read/Write: CHK_ON, CHK_OFF Prohibition for Filter Reset control from the local panel Read/Write: CHK_ON, CHK_OFF Operational status for LOSSNAY or OA Read/Write: HIGH, LOW, OFF Status for Filter Dirty Read: ON, OFF Write: RESET Error status Read: ON, OFF Write: RESET Ambient Temperature Read: 00 to 999 Communication error with G50 Virtual signal generated by IntesisBox to indicate the status of the communication with the G50 Group communication error Virtual signal generated by IntesisBox to indicate that the group is not configured into the G50 Polling active Virtual signal to indicate or set if the Group is active or not active during the polling process Group Alarm Code This signal provides a value Each value has an associated alarm that has occurred in the group (0 means no alarm) 1 PWFY units have a different mode and settemp map explained in the signals column in LinkBoxEIB (section 34 in the User Manual) TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 8 / 11

9 6 Configuration tool LinkBoxMB Visual engineering tool, easy of use, for gateway s configuration and supervision compatible with Microsoft Windows operating systems, supplied with the gateway free of charge Multi-window tool allowing to supervise simultaneously the communication activity with both protocols (systems), real time values for all the signals allowing to modify any value (very useful for test purposes), console window showing debug and working status messages, and configuration windows to configure all the gateway s parameters and signals Signals configuration in plain text files (tab separated) for easy and quick configuration using Microsoft Excel (very useful in projects with a lot of points) Allows configuring the gateway s parameters and signals while in off-line (not connected to the gateway) Connection to the gateway for download the configuration and supervision by using serial COM port of the PC (serial cable supplied with the gateway) Allows configuring all the external protocols available for IntesisBox Server series Upgrades for this software tool available free of charge whenever a new protocol is added to the IntesisBox Server series Multi-project tool allowing having in the engineer s PC the configuration for all the sites with different IntesisBox Server series gateways Multi-language tool, all the language-dependent strings are in a plain text file (tab separated) for easy modification or addition of new languages A list of system commands is available to send to the gateway for debugging and adjust purposes (Reset, Date/time consultation/adjust, Firmware version request ) 7 TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 9 / 11

10 Mechanical & Electrical characteristics Envelope Plastic type PC (UL 94 V-0) Size: 107mm x 105mm x 58mm Color Grey RAL 7035 Power 9 to 30VDC +/-10% 14W 24VAC +/-10% 14VA Power connector is a 2 pole plug-in screw terminal bloc Mounting options Wall DIN rail EN60715 TH35 RTU ports 1 x Serial RS232 (DB9 male DTE) 1 x Serial RS485 (Plug-in screw terminal block 2 poles) TCP & 1 x Ethernet 10BT RJ45 connector Mitsubishi ElecG50 port LED indicators 1 x Power 2 x Ethernet port link and activity (LNK, ACT) 2 x RTU port activity (Tx, Rx) Console port RS232 DB9 female connector (DCE) Configuration Via console port 1 Firmware Allows upgrades via console port Operational 0 C to +70 C temperature range Operational humidity 5% to 95%, non condensing range Protection IP20 (IEC60529) RoHS conformity Compliant with RoHS directive (2002/95/CE) Certifications CE 1 Along with the device it is also supplied a standard DB9 male - DB9 female 18 m cable for configuring and monitoring the device using a PC via serial COM port The configuration software, compatible with MS Windows operating systems, is also supplied TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 10 / 11

11 8 Dimensions Power + Ethernet port 58 mm RTU RS232/485 Console port 107 mm 105 mm Recommended available space for its installation into a cabinet (wall or DIN rail mounting), with space enough for external connections: 100 mm 115 mm 130 mm TRADEMARKS: Todas las marcas y nombres utilizados en este documento se reconocen como marcas registradas de sus respectivos propietarios 11 / 11