4DB01R0/1 0/01 Data Bulletin Replaces 4DB01R9/04 Square D Load Center Sht-Circuit Current Ratings Retain f future use. Introduction Fully-Rated System Series-Rated System Two-Tier Series Rating This document defines fully-rated systems, two-tier series sht circuit current protection and three-tier series sht circuit current protection. It also addresses NEC requirements and illustrates series rating labels currently provided with Square D multi-metering and load center equipment manufactured by Schneider Electric. The location of series rating labels applied to Square D load centers is depicted on pages and of this document. In a fully rated system, the interrupting rating of all the overcurrent protective devices must be greater than equal to the available fault current at the line side terminals of each device. The NEC and UL permit assigning a sht circuit current rating to a tested combination of circuit breakers fuses that is higher than the individual rating of the downstream overcurrent protective device. Testing by the circuit breaker manufacturer demonstrates that the combination can safely interrupt the available fault current. NEMA defines a series rating as follows: Series Rating A sht-circuit interrupting rating assigned to a combination of two me overcurrent protective devices which are connected in a series and in which the rating of the downstream device(s) in the combination is less than the series rating. The combination of overcurrent protective devices may be enclosed in a single piece of equipment such as a load center. Three-tier series rated systems are most commonly designed with the supply side device in a separate enclosure, such as metering equipment, that feeds a load center. NOTE: The load-side device is always a circuit breaker. The supply-side device may be either a circuit breaker a set of current-limiting fuses. A two-tier series rating can be used within a single enclosure (Example 1) in separate enclosures (Example ). Example 1: QO Main Circuit Load Center ka QOM VH 00 A QO A Example : MP Meter-Pak Feeding Homeline Main Lug Load Center ka 10 ka QOM MVH 00 A HOM A 00 01 Schneider Electric All Rights Reserved
Square D Load Center Sht-Circuit Current Ratings 4DB01R0/1 Data Bulletin 0/01 Location of Two-Tier Series Ratings Label in Schneider Electric Equipment Figure 1: Two-Tier Series Ratings Label Application The permitted NEC and UL series ratings are found marked in the equipment. Unless the equipment is marked, one cannot be assured the circuit breaker combination will perfm appropriately in the enclosure. Schneider Electric marks two-tier series ratings on the inside wall of load centers (See Figure 1). The two-tier series rating labels applied to current production convertible main QO and fixed main Homeline load centers are depicted in Figures and 5, respectively. NOTE: The infmation contained in this data bulletin is current at time of printing; however, ratings may change additional ratings may be added without notice. Refer to the series-connected ratings marked on the equipment. Two-tier series rating labels are applied to the side wall of current production QO and Homeline load centers. Figure : QO Two-Tier Series Ratings Labels f Convertible Main Load Centers QO LOAD CENTER LUG TORQUE DATA SHORT CIRCUIT CURRENT RATING See circuit breaker See circuit breakers and field installed units f wire binding screw tque. RMS SymmetricaL Integral Remote f voltage and Circuit IEC 6049-1 See Panelboard Interi f No. Amperes Main / interrupting rating. Wire Range (AWG/ kcmil) Tque (lb - in) X 0 @ V~ Max. Fuse Class (Max. A) The rating is equal to (Max. A) Box / Caja Cat. No. BX1A Line Neutral the lowest interrupting Use Cover No. Lug 4 - /0 CU / AL rating of any circuit Utilice la Cubierta No. de o: Main Lug 6 - /0 CU / AL 5 @ 40 QO - H breaker installed. Refer to branch QOC4US /o QOC4UF Alternate 10 @ 40 QO (15), QO - H Main main circuit breakers Mains 15A max. / Linea principal de 15A max. QO - VH (15) f individual ratings. See main service disconnect rating if installed. Neutral and Equipment Ground Bar @ 40 QO - VH () QO () Additional ELECTRIC CABINET - 60 Hz. Tque ( lb - in) Bar with 1 replacement branch BOX V-81 Wire Range (AWG) 40 V~ Max. - Phase/Fases (UL). Bar with screw sizes screw size 65 @ 40 QH main circuit breaker, 1/0- CU / AL Large Small Ue 415Y/40 V~, Phase/Fases - 4 wire/hilos (IEC). @ 40 T (15) QO (15) service disconnect 4-CU / AL Large 45 Small 5 MUST have an F intallation, repairs alterations, Ui,000 volts (IEC) 6-CU / AL Large 45 Small 5 5 5 @ 40 QD (15) 1 pole QO interrupting rating Call an electrical contract electrician. 4 circuits / 4 circuitos max. 8-CU / AL Large 40 Small 10 5 65 @ 40 QG (15) pole QO (15) equal to greater Maximum continuous loads not to exceed Type 1 (IP0) Enclosure / Gabinete Tipo 1 10-14-CU, 10-1 AL Large 5 Small 10 0 pole QO () than that of the circuit 80% of the ampere rating of any over current @ 08Y/10 QJ (15) pole () F 40 V~, Ph- W system, use only breakers breaker with the device installed. Equipment Ground Combinations (4.5 peak) @ 415Y/40 QOXD () lowest interrupting Las cargas máximas continuas no deben rated 40 V. rating presently exceder el 80% de la capacidad en A de F 40/10 V~, Ph - 4 W delta systems, B phase 10 (17 peak) @ 415Y/40 QO - VS (6) cualquier equipo de sobrecriente instalado. Two 14 1 CU, Two 1 AL 5 10 5 installed. See must be 08 V~ to neutral. poles 40 V~, Ph W. Grounded B phase. QO includes suffixes panelboard interi f Date Code 5 connected to phase B must be rated 40 V~. Two 10 AL 5 AFI, EPD, EPE and GFI. includes suffixes AFI and GFI. circuit breaker types. 4065-51-05 Three-Phase QO Load Centers 15 A Max. QO LOAD CENTER See Panelboard Interi f No. Box / Caja Cat. No. BX1D Use Cover No. Utilice la Cubierta No. de o: QOC4US /o QOC4UF Mains 15A max. / Linea principal de 15A max. See main service disconnect rating if installed. - 60 Hz. 40 V~ Max. - 1 Phase/Fases (UL). Ue 40 V~, 1 Phase/Fases - wire/hilos (IEC). Ui,000 volts (IEC) 4 circuits / 4 circuitos max. Type 1 (IP0) Enclosure / Gabinete Tipo 1 LUG TORQUE DATA See circuit breakers and field installed units f wire binding screw tque. Line Neutral Lug Main Lug Alternate Main Wire Range (AWG) 1/0- CU / AL 4-CU / AL 6-CU / AL 8-CU / AL 10-14-CU, 10-1 AL Wire Range (AWG/ kcmil) Tque (lb / in.) 4 - /0 CU / AL 6 - /0 CU / AL Neutral and Equipment Ground Bar Tque (in - lbs) Bar with screw sizes Large Small Large 45 Small Large 45 Small 5 Large 40 Small 10 Large 5 Small 10 Equipment Ground Combinations Two 14 1 CU, Two 1 AL Two 10 AL 5 5 10 Bar with 1 screw size 5 5 5 0 5 5 RMS SymmetricaL Amperes X 0 @ V~ Max. 5 @ 40 10 @ 40 @ 40 5 @ 40 4 @ 40 SHORT CIRCUIT CURRENT RATING Integral Remote Main / Fuse Class (Max. A) Circuit (Max. A) QO - H QO () & QO - VH (), QO () & QO () & QO - VH (15), QOM - VH (15) QD (15) () QO () & 65 @ 40 QH QG (15) QO () & @ 40 QJ (15) ; T (15) QO () & (4.5 peak) @ 40 QOXD (6) 40 V~, Ph W. Grounded B phase. QO includes suffixes ; GFI, EPD, PL, AS and AFI. includes suffixes: GFI and AFI. Single-Phase QO Load Centers 15 A Max. See circuit breaker f voltage and interrupting rating. The rating is equal to the lowest interrupting rating of any circuit breaker installed. Refer to branch main circuit breakers f individual ratings. Additional replacement branch main circuit breaker, service disconnect MUST have an interrupting rating equal to greater than that of the circuit breaker with the lowest interrupting rating presently installed. See panelboard interi f circuit breaker types. IEC 6049-1 F intallation, repairs alterations, Call an electrical contract electrician. Maximum continuous loads not to exceed 80% of the ampere rating of any over current device installed. Las cargas máximas continuas no deben exceder el 80% de la capacidad en A de cualquier equipo de sobrecriente instalado. Date Code 407-47-01 00 01 Schneider Electric All Rights Reserved
4DB01R0/1 Square D Load Center Sht-Circuit Current Ratings 0/01 Data Bulletin Figure : (Continued) QO Two-Tier Series Ratings Labels f Convertible Main Load Centers QO LOAD CENTER See Panelboard Interi f No. Box / Caja Cat. No. BX8A Use Cover No. Utilice la Cubierta No. de o: QOC4US /o QOC4UF Mains 5A max. / Linea principal de 5A max. See main service disconnect rating if installed. - 60 Hz. 40 V~ Max. - 1 Phase/Fases (UL). Ue 40 V~, 1 Phase/Fases - wire/hilos (IEC). Ui,000 volts (IEC) 4 circuits / 4 circuitos max. Type 1 (IP0) Enclosure / Gabinete Tipo 1 LUG TORQUE DATA See circuit breakers and field installed units f wire binding screw tque. Main & Neutral Lugs Service Ground Alternate Main Wire Range (AWG/ kcmil) Tque (lb / in.) 4-0 CU / AL 6 - /0 CU / AL Neutral and Equipment Ground Bar Tque (in - lbs) Bar with 1 Wire Range (AWG) Bar with screw sizes screw size 1/0- CU / AL Large Small 4-CU / AL Large 45 Small 5 6-CU / AL Large 45 Small 5 5 8-CU / AL Large 40 Small 10 5 10-14-CU, 10-1 AL Large 5 Small 10 0 Equipment Ground Combinations Two 14 1 CU, Two 1 AL 5 10 5 Two 10 AL 5 5 RMS SymmetricaL Amperes X 0 @ V~ Max. 5 @ 40 10 @ 40 @ 40 5 @ 40 4 @ 40 SHORT CIRCUIT CURRENT RATING Integral Remote Main / Fuse Class (Max. A) QO - VH, QOM - VH QD (5) 65 @ 40 QG (5) @ 40 QJ (5) ; T (00) (4.5 peak) @ 40 Circuit (Max. A) QO - H QO & QO - VH, QO & QO & QO (15) & QH QO & QO & QOXD (6) 40 V~, Ph W. Grounded B phase. QO includes suffixes ; GFI, EPD, PL, AS and AFI. includes suffixes: GFI and AFI. See circuit breaker f voltage and interrupting rating. The rating is equal to the lowest interrupting rating of any circuit breaker installed. Refer to branch main circuit breakers f individual ratings. Additional replacement branch main circuit breaker, service disconnect MUST have an interrupting rating equal to greater than that of the circuit breaker with the lowest interrupting rating presently installed. See panelboard interi f circuit breaker types. IEC 6049-1 F intallation, repairs alterations, Call an electrical contract electrician. Maximum continuous loads not to exceed 80% of the ampere rating of any over current device installed. Las cargas máximas continuas no deben exceder el 80% de la capacidad en A de cualquier equipo de sobrecriente instalado. Date Code 407--01 Single-Phase QO Load Centers 1 A 5 A Three-Tier Series Rating A three-tier series rating consists of three levels of overcurrent protection devices (the furthest load-side device being a circuit breaker). Per NEC 40.86, this three-tier combination of overcurrent protection must be marked on the end-use electrical equipment (load center). See Example. Example : EZM Fusible Main Device feeding EZM Device feeding Homeline Main Lug Load Center ( ka Three-Tier Series Rating) ka 10 ka Class T 0 V ac QO VH 15 A HOM A Location of Three-Tier Series Ratings in Square D Equipment Figure : Convertible Main Load Centers Label Locations F convertible main load centers, three-tier series ratings labels are applied on the back side of indo load center covers and on outdo load center deadfronts (See Figure ). The infmation contained on this three-tier series rating label is shown in Figure 4. F single-phase fixed main indo and outdo load centers, two-tier and three-tier ratings are printed on the same label. This label is located on the left side wall (See Figure ). The infmation contained on the series rating label f single-phase fixed main load centers is depicted in Figure 5. Three-tier series rating label is applied to the dead front trim of current production convertible main QO and Homeline outdo load centers. Three-tier series rating label is applied to the backside of current production convertible main QO and Homeline covers f indo load centers. Two-tier / three-tier series rating label is applied to left side wall of current production single-phase fixed main QO and Homeline indo and outdo load centers. 00 01 Schneider Electric All Rights Reserved
Square D Load Center Sht-Circuit Current Ratings 4DB01R0/1 Data Bulletin 0/01 Figure 4: Three-Tier Series Ratings Label Applied to Convertible Main QO and Homeline Load Centers Val nominal 4,000 at 40 4,000 at 40 at 40,000 at 40 4,000 at 40 at 40,000 at 40, pole at 40, pole,000 at 08Y/10, pole Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val Class R, J, T RG (000), RJ (000) MHF, Class R, J, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 0 00 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. Figure 5: Two- and Three-Tier Series Rating Label Applied to Fixed Main Homeline Load Centers Interrupting Rating RMS Symmetrical Amperes at 10/40 Vac Max. Val nominal de interrupción A simétricos rcm, 10/40 V~ (ca) máx. SHORT CIRCUIT CURRENT RATING / VALORES NOMINALES DE LA CORRIENTE DE CORTOCIRCUITO Line Si Circuit Fuse Class [ Remote only ] catálogo de los interruptes automáticos SQUARE D del lado de línea [ Remoto solamente ] (Max. A rating / Val nominal máx. en A) Poles Tenant SQUARE D Circuit [ Remote only ] Interrupt Automático del Usuario [ Remoto solamente ] Designación de Catálogo Poles Current Rating Ampere Max. Criente SQUARE D Circuit Interruptes Automáticos Designación de Catálogo Current Rating Ampere Max. Criente Nominal A Máx. Pole Poles 10.000,000 (15) HOM 15 5,000 QD (5) 4,000 4,000, HOM, RG (000), RJ (000) 15,000 MHF, Class R, J, T6, T, L (), 4,000 LA, MA, QD 5 QG (5) LH, MG, MH, PG, PA (1600), RG (000), QD 5 HOM 15 QJ (5),000 RJ (000), Class R, J, T6, L (), QD 5 The Sht Circuit Current Rating is equal to the lowest interrupting rating of any circuit breaker Load centers with A mains rating are installed combination series connected circuit breaker. Additional replacement circuit limited to A maximum integral main breaker(s) MUST have an interrupting rating equal to greater than that of the circuit breaker with the lowest interrupting rating presently installed. See panelboard wiring diagram f circuit breaker types. La criente nominal de ctocircuito es igual al val nominal de interrupción más bajo de cualquier interrupt automático instalado o combinación de interruptes automáticos conectados en serie. El interruptes automáticos adicional o de repuesto DEBE tener un val nominal de interrupción igual o may que el del interrupt automático con el val nominal de interrupción más bajo de cualquier interrupt automático instalado. Vea el interi del tablero para obtener datos sobre los tipos de interruptes automáticos. circuit breaker and A maximum branch circuit breaker. Los centros de carga con una línea principal de A nominales están limitados a A como máximo para el interrupt automático principal integral y A como máximo para el interrupt automático derivado. See circuit breaker f voltage and interrupting rating. Consulte los datos del interrupt automático para obtener los vales nominales designation HOM includes suffixes: AFI, BB, EPD, & GFI. La designación de catálogo HOM incluye sufijos: AFI, BB, EPD, y GFI. 4065-8-0 Applied to Fixed Main Homeline Load Centers Applied to Single-Phase Fixed Main QO Load Centers How to Read the Three-Tier Series Rating Label Figure 6: Selecting Sht Circuit Current Rating Read the label from left to right. Select the appropriate sht circuit current rating, and then read across the row to select main disconnect, tenant circuit breaker and load center circuit breakers. See example below in Figure 6. Val nominal Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val 4,000 at 40 Class R, J, T 4,000 at 40 at 40 RG (000), RJ (000),000 at 40 4,000 at 40 MHF, Class R, J, T6, T, L () at 40,000 at 40, pole LH, MG, MH, PG, PA (1600), RG (000) at 40, pole,000 at 08Y/10, pole RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 0 00 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. 65 ka 10 ka The highlighted ption in the label above depicts the system shown to the right. LHP6400 EZM Main Device (EZM400CB) Feeding EZM Device (EZM15) QDPTM HOM A 4 00 01 Schneider Electric All Rights Reserved
4DB01R0/1 Square D Load Center Sht-Circuit Current Ratings 0/01 Data Bulletin The same series rating infmation is supplied on all convertible main QO and Homeline load centers covers. The figures below explain which ptions of the label apply to the different types of end use equipment. Val nominal 4,000 at 40 4,000 at 40 at 40,000 at 40 4,000 at 40 at 40,000 at 40, pole at 40, pole,000 at 08Y/10, pole Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val Class R, J, T RG (000), RJ (000) MHF, Class R, J, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 00 0 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. F Three-Phase QO Load Centers Val nominal 4,000 at 40 4,000 at 40 at 40,000 at 40 4,000 at 40 at 40,000 at 40, pole at 40, pole,000 at 08Y/10, pole Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val Class R, J, T RG (000), RJ (000) MHF, Class R, J, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 0 00 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. F Single-Phase Convertible Main QO Load Centers Protected with QD QG Tenant Circuit s Val nominal 4,000 at 40 4,000 at 40 at 40,000 at 40 4,000 at 40 at 40,000 at 40, pole at 40, pole,000 at 08Y/10, pole Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val Class R, J, T RG (000), RJ (000) MHF, Class R, J, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 0 00 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. F Homeline Convertible Main Load Centers Protected with Tenant Circuit Val nominal 4,000 at 40 4,000 at 40 at 40,000 at 40 4,000 at 40 at 40,000 at 40, pole at 40, pole,000 at 08Y/10, pole Line Si Circuit catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val Class R, J, T RG (000), RJ (000) MHF, Class R, J, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) RJ (000), Class R, J, T, T6, L () (Integral Remote) / Interrupt Automático del Usuario (15) (15) (15) QD (5) QG (5) SQUARE D Circuit / de Interrupt Automático Interrupt 0 0 00 15 Main Interrupt Interrupt 00 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. F Homeline Convertible Main Load Centers Protected with Two-Pole QD QG Tenant Circuit s 00 01 Schneider Electric All Rights Reserved 5
Square D Load Center Sht-Circuit Current Ratings 4DB01R0/1 Data Bulletin 0/01 How to Read the Series Rating Label f RB devices HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Apply appropriate personal protective equipment (PPE) and follow safe electrical wk practices. See NFPA E. This equipment must only be installed and serviced by qualified electrical personnel. Turn off all power supplying this equipment befe wking on inside equipment. Always use a properly rated voltage sensing device to confirm power is off. Replace all devices, dos, and covers befe turning on power to this equipment. Failure to follow these instructions will result in death serious injury. PELIGRO DE DESCARGA ELÉCTRICA, EXPLOSIÓN O DESTELLO POR ARQUEO Utilice equipo de protección personal PELIGRO (EPP) apropiado y siga las prácticas de seguridad eléctrica establecidas p su Compañía (consulte la nma NFPA E). Solamente el personal eléctrico especializado deberá instalar y prestar servicio de mantenimiento a este equipo. Desenergice el equipo antes de realizar cualquier trabajo en él. Siempre utilice un dispositivo detect de tensión nominal adecuado para confirmar la desenergización del equipo. Vuelva a colocar todos los dispositivos, las puertas y las cubiertas antes de volver a energizar el equipo. El incumplimiento de estas instrucciónes podrá causar la muerte o lesiones serias. This equipment is designed and tested by Square D to perfmance levels which exceed Underwriters Labaties Standards. Use of Other than Square D Circuit s May Adversely Affect User Safety and Impair Reliability. Square D disclaims all liability f damage, injury non-perfmance caused by the use failure of non-square D circuit breakers. Este equipo ha sido diseñado y probado p Square D y supera las nmas de nivel de rendimiento establecidas p Underwriters Labaties (UL). El uso de interruptes automáticos que no sean de Square D puede afectar negativamente la seguridad del usuario y deteriar la confiabilidad del equipo. Square D no asume responsabilidad alguna p daños, lesiones o funcionamiento inadecuado del equipo causado p el uso o desperfectos de interruptes automáticos que no sean de Square D. HOMELINE-SHORT CIRCUIT CURRENT RATING / Criente nominal de ctocircuito-homeline Interrupting Rating RMS Symmetrical Amperes at 40Vac Max. Val nominal de interrupción A simétricos rcm a 40V~ máx. 4,000,000 4,000,000 Interrupting Rating RMS Symmetrical Amperes at 40Vac Max. Val nominal de interrupción A simétricos rcm a 40V~ máx. 4,000 4,000 Line Side SQUARE D Circuit Fuse Class Clase de fusible o designación de catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val LH, MG, MH,MJ, PG, PJ, PA (1600), RG (000), RJ (000) MHF, Class J, R, T6, T, L () LH, MG, MH, PG, PA (1600), RG (000) MJ, MHF, PJ, RJ (000), Class R, J, T6, T, L () Line Si Circuit Fuse Class Clase de fusible o designación de catálogo de los interruptes automáticos SQUARE D del lado de línea (Max. A rating / Val,000 MJ, MHF, PJ, RJ (000),,000 at Class R, J, T6, T, 08Y/10 L () Poles Tenant SQUARE D Circuit (Integral Remote) Interrupt Automático del Usuario de SQUARE D (Ampere Max.) Designación de Catálogo (15) (15) QD (5) QD (5) QG (5) Poles Main Interrupt Automático Principal QOM1- VH None QO-SHORT CIRCUIT CURRENT RATING / Criente nominal de ctocircuito-qo, LH, MH, MHF, PA (1600), Class R, J, T LH, MG, MH, PG, PA (1600), RG (000) QO ( ) SQUARE D Circuit Interrupt Automático Designación de Catálogo 1 Pole HOM ( ) HOM ( ) 0 Current Rating Ampere Max. Criente Nominal A Máx. 15 See circuit breaker f voltage and interrupting rating. / Consulte los datos del interrupt automático para obtener los vales nominales See box label f additional sht circuit current ratings and restrictions. / Consulte la etiqueta de la caja para obtener infmación adicional sobre la criente nominal de ctocircuito y restricciones. HOM incluye los sufijos AFI, BB, EPD y GFI QO incluye los sufijos AFI, EPD, EPE, GFI y PL A Max. in load centers with 15 A Max. mains rating. / A máx. para centros de carga con val nominal en la linea principal de 15 A máx. Pole Polo 00 Tenant SQUARE D Circuit SQUARE D (Integral Remote) Circuit Interrupt Automático Interrupt Automático de del Usuario de SQUARE D SQUARE D Poles Current Rating Ampere Max. (Ampere Max.) Poles Designación Criente Nominal Designación de de Catálogo A Máx. Catálogo 1 Pole Pole Pole Polo Polo QO ( ) (15) 0 QO ( ) 00 QD (5) QG (5) S1B84910 6 00 01 Schneider Electric All Rights Reserved
4DB01R0/1 Square D Load Center Sht-Circuit Current Ratings 0/01 Data Bulletin NEC Requirements Figure 7: Example of Label Provided Two sections of the NEC address markings of series ratings: Section 110. and Section 40.86(b). Per Section 110., the equipment must be legibly marked in the field to indicate the equipment has been applied with a series combination rating. The intent of this section is to alert the installer that the circuit breakers were installed based on a series rating, and to mark the equipment with the sht circuit current rating being applied in the series combination. Schneider Electric provides a label f this purpose with all MP Meter-Pak Meter Centers and EZ Meter-Pak Meter Center Devices. The label is not applied by Schneider Electric, but is provided loose in these devices f application when series ratings are applied by the installer. SERIES COMBINATION SYSTEM RATED AMPERES. IDENTIFIED REPLACEMENT COMPONENTS REQUIRED. Additional replacement circuit breakers must be manufactured by Square D and have a sht circuit current rating equal to greater than that of the circuit breaker(s) presently installed. Refer to additional infmation provided with this equipment. Failure to do so can result in electrical explosion and fire. CAUTION / PRECAUCION SISTEMA COMBINADO EN SERIE CORRIENTE NOMINAL: A ES NECESARIO IDENTIFICAR EL COMPONENTE DE REPUESTO Los interruptes automáticos adicionales o de repuesto deben ser productos de Square D; su criente nominal de ctocircuito debe ser igual que o may que la de los interruptes automáticos actualmente instalados. Consulte la infmación adicional incluida con el equipo. El incumplimiento de esta instrucción puede causar una explosión eléctrica e incendio. Section 40.86(b) requires that the series combination of overcurrent protective devices be tested and marked on the end use equipment. This marking is applied by the manufacturers of switchboards, panelboards, load centers, etc. Schneider Electric marks load center enclosures and covers with series ratings per Figures 1 and. A series rated system is an affdable, viable alternative to a fully rated system. Series ratings can be two-tiered multi-tiered, depending on the levels of overcurrent protection tested and certified. Series ratings include circuit breaker/circuit breaker combinations and also fuse/circuit breaker combinations, but the furthest load side overcurrent protective device is always a circuit breaker. Overcurrent protective device combinations used in series rated systems should be marked on the end use equipment by the electrical distribution product manufacturer. Equipment installed as part of a series rated system must be marked in the field to indicate the sht circuit current rating being applied in the series combination. 00 01 Schneider Electric All Rights Reserved 7
Square D Load Center Sht-Circuit Current Ratings 4DB01R0/1 Data Bulletin 0/01 Schneider Electric USA, Inc. 1415 S. Roselle Road Palatine, IL 60067 USA 1-888-778-7 www.schneider-electric.us Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric f any consequences arising out of the use of this material. Square D and Schneider Electric are trademarks registered trademarks of Schneider Electric. Other trademarks used herein are the property of their respective owners. 8 00 01 Schneider Electric All Rights Reserved